Water Hose - Hitachi HES-35RD Instruction And Installation Manual

∑à Õ πÈ "
3.

WATER HOSE

1) „™â ‡ §√◊ Ë Õ ß¡◊ Õ ∑' Ë ∂ Ÿ ° µâ Õ ß„π°"√µ' ¥ µ— È ß
Use proper tools for the installation
❑
Õ¬à " ¢— π „Àâ π Á Õ µæ≈" µ' ° ·µ°
❑
¢— π πÁ Õ µæ≈" µ' ° „Àâ µ ÷ ß ‡æ◊ Ë Õ ¡' „ Àâ π È " ‰À≈´÷ ¡ ÕÕ°¡"‰¥â
❑
Never tighten the plastic nuts until they break.
❑
Tighten the plastic nuts to prevent water leakage.
§"‡µ◊ Õ π
Warning
❑
Õ¬à " ≈◊ ¡ „ à ª –‡°Á π ¬"ß ∑"ß∑à Õ πÈ " ‡¢â " πÈ " ÕÕ°
❑
‰¡à § «√„™â º â " ‡∑ªæ— π ‡°≈' ¬ «∫√' ‡ «≥∑"ßπÈ " ‡¢â " ·≈–∑"ßπÈ " ÕÕ°
❑
Àâ " ¡∑"°"√ª√— ∫ À√◊ Õ ·°â ‰ ¢™ÿ ¥ Õÿ ª °√≥å ª Ñ Õ ß°— π ·√ߥ— π πÈ " ‡°' π ‚¥¬‡¥Á ¥ ¢"¥
❑
Do not forget to put in the rubber rings on water inlet and the
water outlet hose.
❑
Do not use any tape at the inlet and outlet water tubes.
❑
Never adjust or modify the safety valve by yourself.
°"√µà Õ "¬‰øøÑ "
4.
1) °à Õ π∑' Ë ® –∑"ß"π‰øøÑ " „¥Ê µâ Õ ß — ∫ «' ∑ ™å µ — ¥ ‰øÕÕ°‡ ' ¬ °à Õ π
Before working on any electrical part, turn off the circuit breaker first.
❑
4
„™â "¬‰ø·∫∫§Ÿ à ¢ π"¥
❑
µà Õ "¬‰ø‚¥¬µ√ß®"°·ºß «' ∑ ™å ¿ "¬„π∫â " π ·≈–µ' ¥ µ— È ß «' ∑ ™å µ — ¥ ‰ø‰«â π Õ°
Àâ Õ ßÕ"∫πÈ "
❑
‡§√◊ Ë Õ ß∑"πÈ " Õÿ à π ®–µâ Õ ßµ' ¥ µ— È ß Õ¬à " ß∂"«√°— ∫ "¬‰øµà Õ ‡¢â " ‡§√◊ Ë Õ ß∑"ß «' ∑ ™å
Õߢ— È « ´÷ Ë ß ¡' ® ÿ ¥ — ¡ º— Àπâ " ∑Õߢ"«¢Õß «' ∑ ™å À à " ß°— π Õ¬à " ßπâ Õ ¬
«' ∑ ™å π ' È µ â Õ ßÕ¬Ÿ à „ π∑' Ë ‡ ÀÁ 𠉥â ß à " ¬¿"¬πÕ°Àâ Õ ßÕ"∫πÈ "
❑
Use 4 or 6 sq. mm. Wire for wiring. (See the table on page 14)
❑
Connect the wire directly from the switch-board of the house
and install a circuit breaker outside the bathroom.
❑
The shower heater must be installed permanently together
with the electric line join with 2 electrodes of circuit breaker, far
from at least 3 mm. The breaker must be seen easily outside
of bathroom.
CONNECTION OF THE WIRES
6 ( 14)
À√◊ Õ µ√.¡¡. ¥Ÿ µ "√"ßÀπâ "
(
∂Ÿ °
À— « Ωí ° ∫— «
Shower head
"¬Ωí ° ∫— «
Shower hose
MEMO
MAX
3
¡¡.
Àâ Õ ßÕ"∫πÈ "
Bathroom
º' ¥
ª–‡°Á π ¬"ß
Rubber ring
MEMO
MAX
«"≈å « ‡ªî ¥ -ªî ¥ πÈ "
Water inlet valve
«' ∑ ™å µ — ¥ ‰ø
Circuit Breaker
"¬¥' π
Earth