Disassembly/Assembly Procedures Of Deck Mechanism - Hitachi DV-PF7E Service Manual

4-2 DISASSEMBLY/ASSEMBLY PROCEDURES OF DECK
MECHANISM
Before following the procedures described below, be sure to remove the deck assembly from the cabinet.
(Refer to CABINET DISASSEMBLY INSTRUCTIONS on page 4-1.)
All the following procedures, including those for adjustment and replacement of parts, should be done in Eject
mode; see the positions of [44] and [45] in Fig. DM1H on page 4-8. When reassembling, follow the steps in
reverse order.
STEP START-
/LOC. ING
No. No.
[1] [1] Guide Holder A
Cassette Holder
[2] [1]
Assembly
[3] [2] Slider (SP)
[4] [2] Slider (TU)
[5] [4] Lock Lever
[6] [2] Cassette Plate
[7] [7] Cylinder Assembly
Loading Motor
[8] [8]
Assembly
[9] [9] ACE Head Assembly
Tape Guide Arm
[10] [2]
Assembly
[11] [10] C Door Opener
[12] [11] Pinch Arm (B)
Pinch Arm (A)
[13] [12]
Assembly
[14] [14] FE Head
[15] [15] Prism
[16] [2] Slider Shaft
[17] [16] C Drive Lever (SP)
[18] [16] C Drive Lever (TU)
[19] [19] Capstan Motor
[20] Clutch Assembly (HI)
[20]
[21] [20] Center Gear
[22] [22] F Brake Assembly (HI)
Worm Holder
[23] [22]
[24] [22] Pulley Assembly (HI)
[25] Mode Gear (LM)
[25]
[26] Mode Lever (HI)
[20],[25]
[22],[23],
[27] Cam Gear (A) (HI)
[26]
[28] [26] TR Gear C
[29] [28] TR Gear Spring
[30] [29] TR Gear A/B
[31] [31] FF Arm (HI)
[32] [26] Idler Assembly (HI)
PART
T DM3H
T DM4H
T DM5H
T DM5H
T DM5H
T DM5H
T DM1H, DM6H
T DM1H, DM7H
T DM1H, DM7H
T DM1H, DM8H-1
T DM1H, DM8H-1
DM1H, DM8H-1,
T
DM8H-2
DM1H, DM8H-1,
T
DM8H-2
T DM1H, DM9H
T DM1H, DM9H
T DM10H
T DM10H
T DM10H
B DM2H, DM11H
B DM2H, DM12H
B DM12H
B DM2H, DM12H
B DM2H, DM13H-1 (S-9), *(L-7), *(L-8)
B DM2H, DM13H-1
B DM2H, DM13H-1 (C-2)
DM2H, DM13H-1,
B
DM13H-2
DM2H, DM13H-1,
B
DM13H-2
B DM2H, DM13H-1 (C-5)
B DM13H-1
B DM13H-1
B DM1H, DM14H
B DM1H, DM14H
REMOVAL
REMOVE/*UNHOOK/
Fig. No. UNLOCK/RELEASE/
UNPLUG/DESOLDER
2(S-1)
(S-1A), *(L-1)
*(L-2)
*(L-3), *(P-1)
Desolder, 3(S-2)
Desolder, LDG Belt,
2(S-3)
(S-4)
*(P-2)
(S-4A), *(L-4)
*(P-3)
(S-5)
(S-6)
*(L-5)
(S-7), *(P-4)
3(S-8), Cap Belt
(C-1)
*(L-6)
(C-3)
(C-4)
*(L-9)
4-6
INSTALLATION
ADJUSTMENT
CONDITION
(+)Refer to
Alignment Sec.
Page 4-15