2.5 Setting the LDAPS Sever ..........23 2.5.1 Importing a Certificate ............23 2.5.2 Root Certificate Authority List..........31 Chapter 3 Mail Server ............35 3.1 Authentication Method for Users Connect to Mail Server ..............36 fi-6010N Network Scanner Associated Servers Setup Guide...
Page 4
3.2 Installing POP3 Service and SMTP Server ....37 3.2.1 Adding the Components of POP3 Service and SMTP Server................37 3.2.2 Creating Mailbox ..............39 3.3 Changing SMTP Server Settings ........41 3.3.1 Access Control ............... 41 3.3.2 Connection Control ..............44 Chapter 4 File Server ............
Introduction This manual explains the procedures for setting the associated servers used by the fi-6010N Network Scanner. The setting procedures explained in this manual are only one example. Setting contents may vary depending on the customers configuration. ■Trademarks Trademarks and Registered Trademarks Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.
This symbol alerts operators to helpful advice regarding operation. HINT ■About Maintenance The user must not perform repairs on this scanner. Contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider for repairs to this product.
Server Environment The following illustrates an example of server environment connecting to this scanner. Send e-mail SMTP Server Internet Send Fax Original Document Fax Server Scanner Scanned Data Print User Authentication Print Server FTP Server LDAP Server Network File Server Save Folder To enable use of all functions of this scanner, read the manual from Chapter 1 to set up the scanner.
2000 Server (*1) WINS ® Windows Server 2003 (*2) WINS ® Windows Server 2008 (*3) DHCP Server DHCP ® Windows 2000 Server (*1) DHCP ® Windows Server 2003 (*2) ® DHCP Windows Server 2008 (*3) fi-6010N Network Scanner Associated Servers Setup Guide...
Page 12
Server Operating system Software product NTP Server Redhat Enterprise Linux Fax Server RightFax ® Windows 2000 Server (*1) ® RightFax Windows Server 2003 (*2) RightFax ® Windows Server 2008 (*3) (*1) ® ® Microsoft Windows 2000 Server ® ® Microsoft Windows 2000 Advanced Server ®...
DNS server. 2.1 Summary........................6 2.2 Communicating to the LDAP Server ..............7 2.3 Installing Active Directory..................8 2.4 Setting Active Directory ..................16 2.5 Setting the LDAPS Sever ..................23 fi-6010N Network Scanner Associated Servers Setup Guide...
Summary The user data is managed on an LDAP server which supports the X.500 directory protocol service. This section describes the following user data. • User Name • Password • E-mail Address When using a LDAP server, set the following data on the LDAP server. Info Save in ...
LDAP server. The LDAP server searches LDAP entries using the search base (DN). If the user name has not been registered in the LDAP server, the login request is refused. fi-6010N Network Scanner Associated Servers Setup Guide...
Installing Active Directory Your computer starts to operate as a domain controller by installing Active Directory. Check the following before installing Active Directory. HINT • Check that the network information (IP address, subnet mask, default gateway, DNS server) is set. •...
Page 17
2.3 Installing Active Directory 4. Click the [Next] button. 5. Click the [Next] button. 6. Select "Domain Controller for a new domain" and click the [Next] button. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 18
7. Select "Domain in a new forest" to set the location of a new domain to be created, and click the [Next] button. 8. Specify "Full DNS name for new domain" and click the [Next] button.
Page 19
2.3 Installing Active Directory 9. Specify "Domain NetBIOS name" and click the [Next] button. 10. Specify the database of Active Directory in the "Database folder" input field. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 20
11. Specify where to store the log in the "Log folder" input field, and click the [Next] but- ton. 12. Specify the folder shared as system volume in the "Folder location" input field, and click the [Next] button.
Page 21
DNS server.", and click the [Next] button. 14. To specify an access permission level for the server applications, select "Permissions compatible only with Windows 2000 or Windows 2003 operating systems", and click the [Next] button. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 22
15. Enter a password to be specified when booting the operating system in "Directory Service Restore Mode" in the "Restore Mode Password" and "Confirm password" input fields, and click the [Next] button. ⇒ Each information you specified is displayed on the screen. 16.
Page 23
2.3 Installing Active Directory 17. Click the [Finish] button. ⇒ The message appears. 18. Follow the message to restart your computer. ⇒ Your computer starts to operate as a domain controller after the restart. fi-6010N Network Scanner Associated Servers Setup Guide...
Setting Active Directory This section describes the following settings. • Creating OU (Organization Unit) • Creating User Account • Changing User Account Properties 2.4.1 Creating OU (Organization Unit) Active Directory has OU, which is the function to classify the objects such as user, computer and group.
Page 25
2.4 Setting Active Directory 3. Specify an OU name to be created and click the [OK] button. ⇒ The specified OU name is added to the list. fi-6010N Network Scanner Associated Servers Setup Guide...
2.4.2 Creating User Account User account may be created in a domain, container, or OU. Set the search base (DN) in the scanner in accordance with the attributes ATTENTION of the LDAP database to be used for creating user data. The following shows an example of how to set the search base (DN) in accordance with the LDAP attributes.
Page 27
2.4 Setting Active Directory 3. Specify the user account information to be created, and click the [Next] button. ⇒ The dialog box to specify a password appears. 4. Specify a password. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 28
5. Clear the "User must change password at next logon" checkbox and click the [Next] button. ⇒ The confirmation screen appears. 6. Confirm the specified information and click the [Finish] button. ⇒ The icon of the created user account is added to the list.
1. Select [Start] - [Administrative Tools] - [Active Directory Users and Computers]. ⇒ The "Active Directory Users and Computers" screen appears. 2. Right-click a user account you want to change, and select [Properties]. ⇒ The properties screen appears. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 30
3. Specify "E-mail" in the [General] tab, and click the [OK] button. ⇒ The E-mail address is set for the user account.
Active Directory. The procedure for importing a certificate is as follows. 1. Select [Start] - [Run]. ⇒ The "Run" dialog box appears. 2. Specify "mmc" in the "Open" field. Click the [OK] button. ⇒ The "Console1" screen appears. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 32
4. Select [File] - [Add/Remove Snap-in]. ⇒ The "Add/Remove Snap-in" dialog box appears. 5. Click the [Add] button. ⇒ The "Add Standalone Snap-in" dialog box appears.
Page 33
2.5 Setting the LDAPS Sever 6. Select "Certificates" and click the [Add] button. ⇒ The "Certificates snap-in" dialog box appears. 7. Select "Computer account" and click the [Next] button. ⇒ The "Select Computer" dialog box appears. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 34
8. Select "Local computer: (the computer this console is running on)", and click the [Finish] button. ⇒ This returns to the "Add Standalone Snap-in" dialog box. Click the [Close] button on the "Add Standalone Snap-in" dialog box. ⇒ This returns to the "Add/Remove Snap-in" dialog box. 10.
Page 35
2.5 Setting the LDAPS Sever 11. Under Console Root, "Certificates (Local Computer)", right-click on "Personal", and select [All Tasks] - [Import]. ⇒ The "Certificate Import Wizard" starts. 12. Click the [Next] button. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 36
13. Click the [Browse] button and select the file that contains the certificate to be imported, and click the [Next] button. For more details about the root certificate authorities registered in the scanner, refer to "2.5.2 Root Certificate Authority List" (page 31).
Page 37
2.5 Setting the LDAPS Sever 15. Select the "Mark this key as exportable" checkbox, and click the [Next] button. 16. Select "Automatically select the certificate store based on the type of certificate" and click the [Next] button. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 38
17. Click the [Finish] button. ⇒ The certificate import process is completed.
Class 3 Public Primary Certification Authority 2028/8/2 Class 3P Primary CA 2019/7/7 Class 3TS Primary CA 2019/7/7 Deutsche Telekom Root CA 1 2019/7/10 Deutsche Telekom Root CA 2 2019/7/10 DST (ANX Network) CA 2018/12/10 DST (NRF) RootCA 2008/12/9 fi-6010N Network Scanner Associated Servers Setup Guide...
2008 do not include a POP3 service component. 3.1 Authentication Method for Users Connect to Mail Server ........ 36 3.2 Installing POP3 Service and SMTP Server ............37 3.3 Changing SMTP Server Settings ................. 41 fi-6010N Network Scanner Associated Servers Setup Guide...
Authentication Method for Users Connect to Mail Server The authentication method for users connecting to the mail server depends on the environment of the POP3 service. How server works Active Authentication method Active Directory Standalone for user account Directory Domain Server General Server Controller...
The "Configure Your Server Wizard" screen appears. 2. Follow the instructions on the screen and click the [Next] buttons until "Server Role" appears. 3. Select [Mail server (POP3,SMTP)] and click the [Next] button. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 46
4. Select a user authentication method. For the authentication methods, refer to "3.1 Authentication Method for Users Connect to Mail Server" (page. 36). Select "Active Directory-Integrated" for instance. 5. Specify "E-mail domain name". In Active Directory domain environment, specifying the same name as Active Directory for "E-mail domain name"...
The "POP3 Service" screen appears. 2. Select a domain for which you want to create a mailbox from the tree, and click "Add Mailbox" on the right. ⇒ The "Add Mailbox" screen appears. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 48
3. Specify a mailbox name. The name specified here is an account name for POP3. For authenticating with Active Direc- tory Integration or local account, specify the same name as the Active Directory domain name or the user logon name of the local account. If there is a user account associated with mailbox, clear the "Create asso- HINT ciated user for this mailbox"...
1. Select [Start] - [Administrative Tools] - [Internet Information Services (IIS) Manager]. ⇒ The "Internet Information Services (IIS) Manager" screen appears. 2. Right-click "Default SMTP Virtual Server", and select [Properties]. ⇒ The "Default SMTP Virtual Server Properties" screen appears. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 50
3. Click the [Authentication...] button in the [Access] tab. ⇒ The "Authentication" dialog box appears.
Page 51
If the "Basic authentication" checkbox is selected, the password will be sent in cleartext using standard commands. If the "Integrated Windows Authentication" checkbox is selected, the client and server will negotiate Windows Security Support Provider Interface. ⇒ User authentication function is set. fi-6010N Network Scanner Associated Servers Setup Guide...
3.3.2 Connection Control Connections to the SMTP server can be controlled under the following conditions. • Specified IP address • Specified computer • IP addresses grouped by subnet mask or domain. The following shows the procedure to permit connections from multiple computers by specifying subnet mask.
Page 53
3.3 Changing SMTP Server Settings 3. Click the [Connection...] button in the [Access] tab. ⇒ The "Connection" dialog box appears. 4. Select "Only the list below" and click the [Add] button. ⇒ The "Computer" dialog box appears. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 54
5. Select "Group of computers" and specify "Subnet address" and "Subnet mask". 6. Click the [OK] button. ⇒ Computers with the specified subnet mask are permitted to connect to the SMTP server.
The file server settings are for creating and publishing a shared folder on the disk of the server. This chapter describes the file server settings. 4.1 Creating a Shared Folder ..................48 4.2 FTP Server Operating Conditions ............... 51 fi-6010N Network Scanner Associated Servers Setup Guide...
Creating a Shared Folder Shared folders are created for a disk of the server. ® This chapter describes the file server settings using Windows Server 2003 as an example. ® The procedure for creating a shared folder with Windows Explorer is as follows. ®...
Page 57
2. On the [Sharing] tab, select "Share this folder", and specify the folder name to share in the "Share name" input field. 3. Click the [Permissions] button. ⇒ The "Permissions" dialog box appears. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 58
4. Set restrictions on the shared folder. The following describes the settings to give write permission to all users. • Select "Everyone" in "Group or user names". • Select the "Allow" checkbox of [Change] in the "Permissions for Everyone". For giving permission to each user or group, click the [Add] button to add a HINT desired user or group to set.
Validated Software The following software has been fully or partially validated to be compatible with this scanner sys- tem. For the latest information, contact your FUJITSU scanner dealer or an authorized FUJITSU scan- ner service provider. ■ FTP Server Software...
(1): ® Windows 2000 Server (2): ® Windows Server 2003 (3): ® Windows Server 2008 Yes: Compatibility verified Compatibility not verified — ■ FTPS Validation Certificates Certificate Type GlobalSign Windows Server self-signed certificate fi-6010N Network Scanner Associated Servers Setup Guide...
A print server provides other computers on a network access to a connected printer. This chapter describes the print server settings. 5.1 Summary........................ 56 5.2 Printer Performance ..................... 57 5.3 Printer Settings ..................... 58 fi-6010N Network Scanner Associated Servers Setup Guide...
Summary The scanned data can be output to the printer connected to the print server. To use the print server, set the following information on the print server. Info Save in ... Used to ... Printer Print server Set a printer to be used with the scanner. The scanner prints on printers connected to the print server.
Printer should allow the status of print errors to be easily checked (via a LCD control panel, or sim- ilar). 5.2.2 Compatible Printers The following printers are known to be compatible with this scanner. For the latest information updates, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider. Maker Model...
Printer Settings Specify a printer on the print server. For more details, refer to "4.7.13 Setting the Network Printers" in the "fi-6010N Network Scanner Operator’s Guide". When using a network printer, note the following. ATTENTION • This scanner can print on a printer connected to the print server. In addition, the scanner cannot print directly to a network printer.
In addition, when a DNS name resolution fails, the query can be transferred to the WINS server. ® This chapter describes the WINS server settings using Windows Server 2003 as an example. 6.1 Installing WINS Server..................60 6.2 Setting Properties of DNS Zone ................61 fi-6010N Network Scanner Associated Servers Setup Guide...
Installing WINS Server The following shows the procedure for adding the WINS server component. 1. Select [Start] - [All Programs] - [Administrative Tools] - [Configure Your Server Wiz- ard]. ⇒ The "Configure Your Server Wizard" screen appears. 2. Follow the instructions on the screen and click the [Next] button until "Server Role" appears.
The procedure for setting properties of a forward lookup zone is as follows. 1. Select [Start] - [Administrative Tools] - [DNS]. ⇒ The "dnsmgmt" screen appears. 2. Right-click on the target domain in "Forward Lookup Zones", and select "Properties". ⇒ The properties screen appears. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 70
3. Select the "Use WINS forward lookup" checkbox in the [WINS] tab. 4. Specify an IP address of WINS server for [IP address], and click the [Add] button. ⇒ The IP address is added to the list. 5. Click the [OK] button. ⇒...
The procedure for setting properties of a reverse lookup zone is as follows. 1. Select [Start] - [Administrative Tools] - [DNS]. ⇒ The "dnsmgmt" screen appears. 2. Right-click a reverse lookup zone you want to set, and select [Properties]. ⇒ The property screen appears. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 72
3. Select the "Use WINS-R lookup" checkbox in the [WINS-R] tab. 4. Specify a domain name for "Domain to append to returned name". 5. Click the [OK] button. ⇒ Properties of the reverse lookup zone are set.
This chapter describes the DHCP server settings using Windows Server 2003 as an example. 7.1 Installing DHCP Server..................66 7.2 Adding the DHCP Server Component and Creating a Scope ......67 7.3 Authorizing DHCP Server..................74 fi-6010N Network Scanner Associated Servers Setup Guide...
Installing DHCP Server ® A DHCP server can be installed manually or using the configuration wizard of Windows Server 2003 as well. After the installation, a range of IP addresses assigned to clients and other TCP/IP parameters must be specified.
3. Select [DHCP server] and click the [Next] button. ⇒ The confirmation screen appears. 4. Click the [Next] button. ⇒ The DHCP server component is added. ⇒ After adding the component, "New Scope Wizard" screen automatically appears. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 76
5. Specify "Name" and "Description", and then click the [Next] button. 6. Specify a start value in "Start IP address" and end value in "End IP address" for the range assigned to clients and click the [Next] button.
Page 77
This is the range from "Start IP address" to "End IP address" specified in Step 6. Leave these fields blank if no exclusion is necessary. 8. Click the [Next] button. 9. Specify an address lease period and click the [Next] button. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 78
10. Select "Yes, I want to configure these options now" and click the [Next] button. You can choose whether to specify TCP/IP parameters other than IP addresses and subnet mask assigned by the DHCP. 11. Specify a default gateway and click the [Add] button. ⇒...
Page 79
The IP address of the DNS server is input in the "IP address" on the right. 14. Click the [Add] button. ⇒ The IP address is added to the list. In this scanner, two DNS servers can be set. HINT 15. Click the [Next] button. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 80
16. If the WINS server is used, specify the IP address of the WINS server. To specify by host name, input the host name of the WINS server for "Server name" and click the [Resolve] button. ⇒ The IP address of the WINS server is input in the "IP address" on the right. 17.
Page 81
7.2 Adding the DHCP Server Component and Creating a Scope 19. Select "Yes, I want to activate this scope now" and click the [Next] button. ⇒ Installing DHCP server and creating scope are completed. Click the [Finish] button to complete. fi-6010N Network Scanner Associated Servers Setup Guide...
Authorizing DHCP Server The DHCP server does not function only by completing installation process. It must be authorized in the Active Directory domain environment. The procedure for authorizing the DHCP server is as follows. 1. Select [Start] - [Administrative Tools] - [DHCP]. ⇒...
This chapter shows an example of how to build an NTP server on Redhat Enterprise Linux. 8.1 Installing NTP Package ..................76 8.2 Automatic Launch of Service ................77 8.3 NTP Server Operation Settings ................78 fi-6010N Network Scanner Associated Servers Setup Guide...
Installing NTP Package In order to use the NTP server function on Redhat Enterprise Linux, the ntp package must be installed. Name 4.2.0.a.20050816 Version ntpd Service Name /usr/sbin/ntpd Daemon Program /etc/ntp.conf Configuration files /etc/init.d/ntpd Control script...
8.2 Automatic Launch of Service Automatic Launch of Service After installing the ntp package, the service is not launched automatically for security reasons. Therefore, set the service to launch automatically using chkconfig. chkconfig ntpd on fi-6010N Network Scanner Associated Servers Setup Guide...
NTP Server Operation Settings Modify /etc/ntp.conf for full-time connection environment setting, which allows communi- cation with higher level NTP servers continuously. Make the basic settings for ntpd since full-time connection environment allows the ntpd to request to the higher level NTP servers at any time. The following shows an example of /etc/ntp.conf for full-time connection environment.
2003 as an example. SMTP Server Mail Box RFAX Fax Server Original Scanned Data Document Send Fax Scanner LDAP Server File Server Print Server 9.1 Installing RightFax....................80 9.2 E-mail Gateway Settings ..................81 fi-6010N Network Scanner Associated Servers Setup Guide...
Installing RightFax For information on installing RightFax, refer to a manual that describes RightFax installation. This scanner uses RightFax E-mail Gateway functions for SMTP/POP3 (henceforth referred to "E- mail Gateway"). The E-mail Gateway monitors specified mailboxes of a mail server. If an e-mail is received, it is accessed by using POP3, imported to the RightFax server, and sent by fax.
Gateway configuration program by double-clicking the RightFax E-mail Gateway service in Enterprise Fax Manager. ⇒The "E-mail Configuration" dialog box opens. 2. Add a new E-mail Gateway. Click the [Add Gateway...] button and select "SMTP/POP3". fi-6010N Network Scanner Associated Servers Setup Guide...
Page 90
For "E-mail delivery direction", set "Both", "Outbound with Notifications", or "Outbound without Notifications". The following explains the available settings for "E-mail delivery HINT direction". • "Both" Sending and receiving with notification • "Inbound Only" Receiving with notification • "Outbound with Notifications" Sending with notification •...
Page 91
3. Startup the E-mail Gateway service. For the service list on the bottom-right of the "RightFax Enterprise Fax Manager" win- dow, right-click "RightFax E-mail Gateway Module", and select "Start Service", to start the service. fi-6010N Network Scanner Associated Servers Setup Guide...
Page 92
Set the fax server e-mail address. Enter the value set in "FROM message" from "Step 2. Add a new E-mail Gateway." (page 81). For more details, refer to "4.7.12 Setting the Fax Server" in the "fi-6010N Network Scanner Operator's Guide".
Page 93
Network Scanner Associated Servers Setup Guide P3PC-2401-01ENZ0 Date of issuance: July 2008 Issuance responsibility: PFU LIMITED Copying of the contents of this manual in whole or in part and copying of the scanner application is forbidden under the copyright law.