Panasonic DMP-BD80 Operating Instructions Manual page 34

Changing the unit's settings
"Display" (continued)
.
( - " To select these options, perform steps
0-0
(Q 32)
I Underlined items are the factory presets.
!
FL Oisplay e Bright
Changes the brightness of the unit's display.
eOim:
The display is dimmed.
eAuto: The display is dimmed during playback and bright
except playback.
SO Card LEO Control fs'Ciiio 1
eOn eOff
Set the lighting method forthe'lamp on the SO card slot. eSO inserted: When this unit is turned on and SO card is inserted, the
lamp is lighted.
License Information about the software used by this unit is displayed.
"TV I Device Connection"
In thiS unit, a P4HO (q 51) Video processor IS used to proVide Video of optimal resolution to the connected TV.
TV Aspect
When connected to a 4:3 aspect television:
Set to match the type of television connected. e4:3 Pan & Scan: Video recorded for a widescreen is played as Pan & Scan
(unless prohibited by the producer of the disc). When playing
BO-Video, video is output as "4:3 Lellerbox".
-4:3 Lellerbox: Video recorded for a widescreen is piayed in the ietterbox style.
When connected to a 16:9 widescreen television:
-16:9: Video recorded for 4:3 aspect screen is displayed as a 4:3 ratio
image in the center of the screen.
e16:9 Full: Video recorded for 4:3 aspect screen is displayed as a
horizontally stretched 16:9 image.
HOMI Connection
ePress [OK] to show the following settings.
HOMI Video Mode eOn: Images are output from the HOMI terminal in the resolution set in "HDMI
Select "On" when video is output from HOM I AV OUT Resolution". Video from COMPONENT VIDEO OUT terminal is output as "480i".
terminal.
eOff Images are output in the resolution set in "Component Video Resolution".
HOMI Resolution*
-Auto:
Automatically selects the output resolution best suited to the
The items supported by the connected devices are connected television (1080p, 1080i, nop or 480p).
indicated on the screen as
"*".
When any item without e480p enop
"*"
is selected, the images may be distorted.
-1080i e1080p
- When outputting 1080p signal, we recommend using High Speed HOMI Cables
that have the HOMIIogo (as shown on the cover) and are less than 5.0 meters to
prevent video distortion etc.
-When the unit is connected to an amplifier/receiver that does not support the
resolution set on the unit, the video cannot be output properly. In this case, use
the HOMI cable to connect the unit to the TV and then connect the unit to the
amplifier/receiver using a cable other than HOMI.
- To enjoy high definition video up-converted to 1080p, you need to connect the unit directly
to 1080p compatible HOTV (High Definition Television). If this unit is connected to an
HDTV through other equipment, it must also be 1080p compatible.
24p Output
I:mI.'J
~
-On: Images in 24p are output in 24p as they are.
When this unit is connected to a TV supporting 1080/24p output However,
via an HDMI cable, this unit displays each frame at 1/24 second
-when video is being output at 24 frames, images from any other terminal
intervals - the same interval originally shot with the film camera.
than the HOM I terminal may not be output properly.
e When playing OVO-Video, set to "On" and then set "24p"
-ImI!I:
when images other than 24p are played, images are output at 60p.
in "Video" (q 31) to "On"
-Off
HOMI RGB Output Range
eStandard: The video is output as it is.
Effective when connected to a device that only supports eEnhanced: When the black and white contrast of a video is low, the signal
RGB output.
is enhanced to reproduce clear video.
HOMI Audio Output
-On:
This setting selects whether or not to output audio from -Off: When the TV is connected to this unit using an HOMI cable, and this unit
HOMI.
is also connected to other devices, such as an amplifier/receiver using an
optical digital audio cable or a coaxial cable
I
B080
I.
VIERA Link
eOn:
Set to use "HOAVI Control" function when connected with
-Off:
Select when you do not want to use "HOAVI Control".
an HOMI cable to a device that supports "HOAVI Control".
Component Video Resolution*
-480i
e480p enop e1080i
This sets the video output resolution when using the Even if you select "nOp" or "1080i", the video output resolution is restricted to "480p" when
component video terminal.
images of OVD-Video discs are output from the COMPONENT VIDEO OUT tenninals.
Analog Audio Output IBosoi
e 2ch (Oownmixl
+
5.1 ch: When connecting to 2ch AUDIO OUT or 5.1ch AUDIO
When connected with AUDIO OUT terminals, you can set OUT. (q 37)
the unit to output the best possible sound for your speakers.
e7.1ch: When connecting to 7.1ch AUDIO OUT. (q 37)
*
I
~
R QT9378