1. Manuals
  2. Brands
  3. Huawei Manuals
  4. Gateway
  5. EchoLife HG510
  6. User manual

Huawei EchoLife HG510 Home Gateway User Manual

Echolife hg510 home gateway
Hide thumbs Also See for EchoLife HG510 Home Gateway:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual
EchoLife HG510 Home Gateway
User Manual

Advertisement

Table of Contents
loading

Related Manuals for Huawei EchoLife HG510 Home Gateway

Summary of Contents for Huawei EchoLife HG510 Home Gateway

  • Page 1 EchoLife HG510 Home Gateway User Manual...
  • Page 2 HUAWEI EchoLife HG510 Home Gateway User Manual V100R001 Huawei Technologies Proprietary...
  • Page 3 Please feel free to contact our local office or company headquarters. Huawei Technologies Co., Ltd. Address: Administration Building, Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, P. R. China Postal Code: 518129 Website: http://www.huawei.com Email: support@huawei.com...
  • Page 4 Copyright © 2005 Huawei Technologies Co., Ltd. All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks , HUAWEI are trademarks of Huawei Technologies Co., Ltd.

  • Page 5: About This Manual

    This manual applies to HG510 V100R001. Related Manuals The related manuals are listed in the following table. Manual Content EchoLife HG510 Home It is used for assisting you in data Gateway User Manual configurations and typical applications. EchoLife HG510 Home...

  • Page 6: Intended Audience

    The manual is intended for the following readers: Technical marketing specialists Installation engineers and technicians Operation and maintenance personnel Conventions The manual uses the following conventions: I. General conventions Convention Description Arial Normal paragraphs are in Arial. Boldface Headings are in Boldface. Huawei Technologies Proprietary...
  • Page 7 Eye-catching symbols are also used in this manual to highlight the points worthy of special attention during the operation. They are defined as follows: Caution, Warning, Danger: Means reader be extremely careful during the operation. Note, Comment, Tip, Knowhow, Thought: Means a complementary description. Huawei Technologies Proprietary...
  • Page 8 Environmental Protection This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed. Huawei Technologies Proprietary...

  • Page 9: Table Of Contents

    User Manual EchoLife HG510 Home Gateway Table of Contents Table of Contents Chapter 1 System Overview ............1-1 1.1 System Features ..............1-1 1.2 System Requirements............1-1 Chapter 2 Hardware Description..........2-1 2.1 Front Panel.................2-1 2.2 Rear Panel .................2-2 2.3 Connecting the HG510 ............2-3 Chapter 3 Configuration Guide ............3-1...
  • Page 10 User Manual EchoLife HG510 Home Gateway Table of Contents 3.4.7 Configuring DSL ............3-42 3.5 Configuring Diagnostics ...........3-42 3.6 Management ..............3-43 3.6.1 Configuring Backing up/Updating/Resetting HG510 Settings................3-44 3.6.2 Viewing System Log ..........3-46 3.6.3 Configuring SNMP Agent ........3-48 3.6.4 Configuring Access Control........3-48 3.6.5 Updating Software ..........3-51...

  • Page 11: Chapter 1 System Overview

    EchoLife HG510 Home Gateway Chapter 1 System Overview Chapter 1 System Overview Welcome to purchase the EchoLife HG510 Home Gateway device(the HG510 for short). With your HG510, you can access the Internet using your high-speed ADSL connection. This User Manual will show you how to install and set up the HG510.
  • Page 12 User Manual EchoLife HG510 Home Gateway Chapter 1 System Overview For system configuration using the supplied web-based program: a web browser such as Internet Explorer V5.0 or later, or Netscape V4.7 or later Huawei Technologies Proprietary...

  • Page 13: Chapter 2 Hardware Description

    Splitter Qualitication Card EchoLife HG510 Home Gateway Quick Quide Note Each carton is deliered with one EchoLife HG510 Home Gateway User Manual. 2.1 Front Panel The front panel provides LEDs that indicate the status of the HG510. Huawei Technologies Proprietary...

  • Page 14: Rear Panel

    User Manual EchoLife HG510 Home Gateway Chapter 2 Hardware Description Table 2-1 lists the LED indicators. Label Color Function Flashes on/off rapidly during the training mode ALARM Flashes on/off slowly: No ADSL link Off: The ADSL link is established and active...

  • Page 15: Connecting The Hg510

    User Manual EchoLife HG510 Home Gateway Chapter 2 Hardware Description Label Function To reset to default settings, Hold the Reset button for more than 5 seconds and then release the button. Connects to the supplied power cable RJ-45 connector: connects the device to your...
  • Page 16 User Manual EchoLife HG510 Home Gateway Chapter 2 Hardware Description DC IN Telephone Power To PC Ethernet Switch 10/100Base-T NIC DC Power in PSTN Reset Figure 2-1 Cable connection Follow the steps listed below to install it. Stage Description See in Connect the ADSL line.
  • Page 17 User Manual EchoLife HG510 Home Gateway Chapter 2 Hardware Description Connect the ADSL line. Method one: Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of the HG510 and insert the other end into the wall socket.
  • Page 18 User Manual EchoLife HG510 Home Gateway Chapter 2 Hardware Description III. Attach the power adapter. Connect the AC power adapter to the PWR connector on the back of the device and plug in the adapter to a wall outlet or power strip.

  • Page 19: Chapter 3 Configuration Guide

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Chapter 3 Configuration Guide 3.1 Preparing Configuration Connect the HG510 and computer with a cross-over/ straight-through Ethernet cable. Power on the HG510. The default IP of the HG510 is 192.168.1.1.
  • Page 20 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-1 Authentication Then click <OK>. If the authentication passes, the home page “Device Info - Summary” will be displayed on the browser. Refer to Figure 3-2. Huawei Technologies Proprietary...

  • Page 21: Configuring The Hg510

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-2 HG510 home page 3.3 Configuring the HG510 The system administrator can configure the HG510 remotely or locally through a Web Browser. Network configuration need to be planned and decided before starting the configuration procedure.

  • Page 22: Configuring Pppoe

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide 3.3.1 Configuring PPPoE Click<Quick Setup> in the left frame, and follow the steps below to create a PPPoE connection. Follow the steps listed below to configure. Stage Description See in Configure ATM PVC 3.3.1 I.
  • Page 23 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Configure ATM PVC Figure 3-3 Quick Setup – ATM PVC Configuration Enter the VPI/VCI values. The actual parameter is provided by your ISPs,you can contact them to get the detailed information.
  • Page 24 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Select Connection Type and Encapsulation Mode Figure 3-4 Quick Setup – Connection Type and Encapsulation Mode Select Connection type ”PPP over Ethernet (PPPoE)”, and select the appropriate “Encapsulation Mode”. Click<Next> to go to next step.
  • Page 25 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide III. Configure PPP Username and Password Figure 3-5 Quick Setup – PPP Username and Password Enter “PPP Username”, “PPP Password”, “PPPoE Service Name”, select “Authentication Method” (AUTO/PAP/CHAP/MSCHAP). The actual parameter is provided by your ISP,you can contact them to get the detailed information.
  • Page 26 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Click<Next> to go to next step. Enable IGMP Multicast and WAN service Figure 3-6 Quick Setup – IGMP Multicast, WAN service Check Enable/Disable IGMP Multicast and WAN Service. Click<Next> to go to next step.
  • Page 27 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Configure LAN Service Figure 3-7 Quick Setup – Device Setup Enter the IP (LAN IP, default 192.168.1.1) address and Subnet Mask (default 255.255.255.0). Select Disable/Enable DHCP Server, if enable DHCP Server , configure the DHCP server parameters.If select...
  • Page 28 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Note: NAT function is by default enabled and is not showing on the page to prevent it from being disabled WAN Setup – Summery Figure 3-8 Quick Setup – WAN Setup – Summary The last page gives a summary of previous steps.

  • Page 29: Configuring Ipoa

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide 3.3.2 Configuring IPoA Click<Quick Setup> in the left frame, and follow the steps below to create a IPoA connection. Follow the steps listed below to configure. Stage Description See in Configure ATM PVC 3.3.2 I.

  • Page 30: Configure Atm Pvc

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Configure ATM PVC Figure 3-9 Quick Setup – ATM PVC Configuration Enter the VPI/VCI values. The actual parameter is provided by your ISPs,you can contact them to get the detailed information.

  • Page 31: Select Connection Type

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Select Connection Type Figure 3-10 Quick Setup – Connection Type and Encapsulation Mode Select “IP over ATM (IPoA)”, and the “Encapsulation Mode”. The actual parameter is provided by your ISPs,you can contact them to get the detailed information.

  • Page 32: Configure Wan Ip Settings

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide III. Configure WAN IP Settings Figure 3-11 Quick Setup– WAN IP Settings Obtain the WAN IP/Subnet Mask, Default Gateway and DNS Server automatically or set them manually.The actual parameter is provided by your ISPs,you can contact them to get the detailed information..

  • Page 33: Enable Nat, Igmp Multicast, And Wan Service

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Enable NAT, IGMP Multicast, and WAN Service Figure 3-12 Quick Setup – IPoA – NAT, IGMP Multicast, WAN service Check Enable/Disable NAT and Firewall functions. Use Advanced Setup/Firewall to assign filter rules.

  • Page 34: Configure Lan Service

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Configure LAN Service Figure 3-13 Quick Setup – Device Setup Enter the IP (LAN IP, default 192.168.1.1) address and Subnet Mask (default 255.255.255.0) . Select Disable/Enable DHCP Server, if enable DHCP Server , configure the DHCP server parameters.If select...

  • Page 35: Configuring Bridge

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide WAN Setup – Summary Figure 3-14 Quick Setup – WAN Setup – Summary The last page gives a summary of previous steps. Make sure that the settings match the settings provided by ISPs, and then Click<Save/Reboot>...
  • Page 36 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Stage Description See in Configure WAN service 3.3.3 III. Configure IP Address 3.3.3 IV. WAN setup-Summary 3.3.3 V. Configure ATM PVC Figure 3-15 Quick Setup – ATM PVC Configuration Enter the VPI/VCI values. The actual parameter is provided by your ISPs,you can contact them to get the detailed information..
  • Page 37 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Select Connection Type Figure 3-16 Quick Setup – Connection Type and Encapsulation Mode Select “Bridging”, and the “Encapsulation Mode”. The actual parameter is provided by your ISPs,you can contact them to get the detailed information..
  • Page 38 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide III. Configure WAN Service Figure 3-17 Quick Setup – WAN Service Enter a service name (default setting is br_0_33) and check the box to enable this WAN service. Click<Next> to go to next step.
  • Page 39 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Configure IP Address Figure 3-18 Quick Setup – Device Setup Enter the LAN IP (default 192.168.1.1) address and Subnet Mask (default 255.255.255.0). Click<Next> to go to next step. Huawei Technologies Proprietary...

  • Page 40: Configuring Mer

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide WAN Setup – Summery Figure 3-19 Quick Setup – WAN Setup – Summary The last page gives a summary of previous steps. Make sure that the settings match the settings provided by ISPS, and then Click<Save/Reboot>...
  • Page 41 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Stage Description See in Configure Connection type and 3.3.4 II. Encapsulation Mode Configure WAN IP settings 3.3.4 III. Enable NAT, IGMP Multicast, and WAN 3.3.4 IV. service Configure LAN Service 3.3.4 V.

  • Page 42: Configure Connection Type And Encapsulation Mode

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Enter the VPI/VCI values. The actual parameter is provided by your ISPs,you can contact them to get the detailed information.. Click<Next> to go to next step. Configure Connection Type and Encapsulation Mode Figure 3-21 Quick Setup –...

  • Page 43: Configure Wan Ip Settings

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide III. Configure WAN IP Settings Figure 3-22 Quick Setup – WAN IP Settings Obtained automatically or set manually the WAN IP/Subnet Mask, Default Gateway and DNS Server. Click<Next> to go to next step.

  • Page 44: Configuring Pppoa

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide WAN Setup – Summery The last page gives a summary of previous steps. Make sure that the settings match the settings provided by ISPS, and then Click<Save/Reboot> to complete the configuration procedure. Refer to “3.3.2 VI.
  • Page 45 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Select Connection Type Select “PPP over ATM (PPPoA)”. Refer to “3.3.1 II. Select Connection Type and Encapsulation Mode”. III. Configure PPP Username and Password Enter PPP Username, PPP Password, and select “Authentication Method”...

  • Page 46: Advanced Setup

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide 3.4 Advanced Setup Advanced Setup allows system administrator to configure the following: Security Routing 3.4.1 Configuring WAN Figure 3-23 Advanced Setup – WAN This page shows the current existing WAN interfaces in the system.

  • Page 47: Configuring Lan

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide 3.4.2 Configuring LAN Figure 3-24 Advanced Setup – LAN Enter the IP address and Subnet Mask, enable/ disable DHCP Server. Configure the second IP Address and Subnet Mask for LAN interface.
  • Page 48 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Virtual Servers Figure 3-25 Advanced Setup – NAT – Virtual Servers Virtual Server allows you to direct incoming traffic from WAN side (identified by Protocol and External port) to the internal server with private IP address on the LAN side.
  • Page 49 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-26 Advanced Setup – NAT – Add new Virtual Server Port Triggering Figure 3-27 Advanced Setup – NAT – Port Triggering Huawei Technologies Proprietary 3-31...
  • Page 50 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Some applications require that specific ports in the Router's firewall shall be opened for access by the remote parties. Port Trigger dynamically opens up the “Open Ports” in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the “Triggering Ports”.

  • Page 51: Configuring Security

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide III. DMZ Host Figure 3-29 Advanced Setup – NAT – DMZ Host The DSL router will forward IP packets from the WAN that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer.
  • Page 52 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Outgoing IP Filtering Figure 3-30 Advanced Setup – Firewall – Outgoing IP Filtering Setup By default, all outgoing IP traffic from LAN is allowed, but some IP traffic can be blocked by setting up filters.
  • Page 53 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-31 Advanced Setup – Firewall – Add new Outgoing IP Filter Click<Add> to create a filter to identify the outgoing IP traffic by specifying at least one condition below. If multiple conditions are...
  • Page 54 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide III. MAC Filtering MAC Filtering is only effective on ATM PVCs configured in Bridge mode. FORWARD means that all MAC layer frames will be forwarded except those matching with any of the specified rules in the following table.

  • Page 55: Configuring Routing

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-33 Advanced Setup – Firewall – Add new MAC Filter 3.4.5 Configuring Routing Three options related to routing information are included. Default Gateway If Enable Automatic Assigned Default Gateway checkbox is...
  • Page 56 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Note: To change the Automatic Assigned Default Gateway from unselected to selected, You need to reboot the router to get the automatic assigned default gateway. Figure 3-34 Advanced Setup – Routing – Default Gateway...
  • Page 57 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Static Route Setup Figure 3-35 Advanced Setup – Routing – Static Route Click<Add> to create a new Static Route. Enter the destination network address, subnet mask, gateway AND/OR available WAN interface and click <Save/Apply> to add the entry to the routing table.
  • Page 58 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide III. RIP Setup Figure 3-37 Advanced Setup – Routing – RIP To activate RIP for the device, select the “Enabled” radio for Global RIP Mode. To configure an individual interface, select the desired RIP version and operation, followed by placing a check in the “Enabled”...

  • Page 59: Configuring Dns Server

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide 3.4.6 Configuring DNS Server Figure 3-38 Advanced Setup – DNS Server If Enable Automatic Assigned DNS checkbox is selected, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment.

  • Page 60: Configuring Dsl

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide 3.4.7 Configuring DSL Figure 3-39 Advanced Setup – DNS Server This page allows you to select the DSL modulation support, telephone cable pair setting, and DSL capability. DSL knowledge is required to configure these settings. Consult your ISPs and make sure that the settings match the settings provided by it.

  • Page 61: Management

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide If a test displays a failure status, click <Test> again to make sure the failure status is consistent. If the test continues to fail, click <Help> to follow the troubleshooting procedure.

  • Page 62: Configuring Backing Up/Updating/Resetting Hg510

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide 3.6.1 Configuring Backing up/Updating/Resetting HG510 Settings System Administrator can back up, update and restore the HG510 settings here. The settings can be saved from the HG510 to computer. The saved setting file can also be loaded from computer to the HG510.
  • Page 63 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Click <Backup Settings> to save the settings to a file on the local computer. Figure 3-42 Management-Setting-Update Click <Browse> to locate the setting file saved on the Local computer. Click <Update Settings> to apply the settings to the HG510 according to the setting file.

  • Page 64: Viewing System Log

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-43 Management-Setting-Restore Default Click <Restore Default Settings> and then confirm the action. 3.6.2 Viewing System Log This allows System Administrator to view the System Log and configure the System Log options.
  • Page 65 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-44 Management-System Log Configure the System Log option. There’re 8 levels of Log Level and Display Level: Emergency, Alert, Critical, Error, Warning, Notice, Informational, and Debugging. The Log Level implies that what log level is applied to the HG510 to keep the log.

  • Page 66: Configuring Snmp Agent

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide 3.6.3 Configuring SNMP Agent System Administrator can enable or disable the embedded SNMP Agent here. SNMP Agent will allow a management application to retrieve statistics and status from the HG510.
  • Page 67 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-46 Management-Access Control-Services Enable the WAN and LAN for each service. FTP, HTTP, ICMP, SNMP, TELNET are supported in the HG510. The IP Address Access Control mode, if enabled, permits access to local management services from IP addresses contained in the Access Control List.
  • Page 68 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-47 Management-Access Control-IP Address Click <Add> to add an IP address to the Access Control List. Mark the Remove option of the specified IP address, then click <Remove> to remove the IP address from the ACL.

  • Page 69: Updating Software

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-48 Management-Access Control-Passwords 3.6.5 Updating Software The new released software can be updated through HTTP. Click <Browse> to locate the new software image file in the computer. Then, click<Update Software> to proceed the software update.

  • Page 70: Save / Reboot

    User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-49 Management-Update Software 3.6.6 Save / Reboot Click <Save/Reboot> to reboot the HG510. The HG510 will automatically save the configuration before reboot, so that modified settings will take effect after reboot.
  • Page 71 User Manual EchoLife HG510 Home Gateway Chapter 3 Configuration Guide Figure 3-50 Management-Save/Reboot Huawei Technologies Proprietary 3-53...

  • Page 72: Chapter 4 Appendix

    User Manual EchoLife HG510 Home Gateway Chapter 4 Appendix Chapter 4 Appendix ADSL Asymmetric Digital Subscriber Line Asynchronous Transfer Mode DHCP Dynamic Host Configuration Protocol Domain Name Server DSLAM Digital Subscriber Line Access Multiplex HTML Hypertext Markup Language Internet Protocols...
  • Page 73 User Manual EchoLife HG510 Home Gateway Chapter 4 Appendix Point to Point Protocol PPPoA PPP over ATM PPPoE PPP over Ethernet Permanent Virtual Connection Routing Information Protocol SNMP Simple Network Management Protocol Transfer Control Protocol Virtual Channel Identifier Virtual Path Identifier...
  • Page 74 Huawei Technologies Co., Ltd. Administration Building, Huawei Technologies Co., Ltd., Bantian, Longgang District, Shenzhen, P. R. China Postal Code: 518129 Website: http://www.huawei.com...

Table of Contents