Toshiba MV13K1 Service Manual page 32

2-12: SUB TINT (AV)
1. Receive the color bar pattern. (Audio Video Input)
2. Connect the synchro scope to TP803.
3. Using the remote control, set the brightness, contrast,
color and tint to normal position.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (4) on the remote control.
The Fig. 2-3 appears on the display.
5. Press the channel button (4) on the remote control.
6. Press the VOL. UP/DOWN button on the remote control
until the section "A" becomes a straight line.
(Refer to Fig. 2-5)
2-13: HORIZONTAL PHASE
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (1) on the remote control.
The Fig. 2-6 appears on the display.
4. Press the channel button (1) on the remote control.
5. Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on right and
left becomes minimum.
1. H. PHASE
2. H. BLK
3. V. SIZE
4. V. POSI
5. V. LIN
6. V. SC
7. V. COMP
8. (H FREQ)
2-14: VERTICAL SIZE
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (1) on the remote control.
The Fig. 2-6 appears on the display.
4. Press the channel button (3) on the remote control.
5. Press the VOL. UP/DOWN button on the remote control
until the horizontal over scan is equal to the vertical over
scan.
ELECTRICAL ADJUSTMENTS
"A"
0. RETURN
2-15: VERTICAL LINEARITY
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (1) on the remote control.
The Fig. 2-6 appears on the display.
4. Press the channel button (5) on the remote control.
5. Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside
and downside becomes minimum.
2-16: VERTICAL POSITION
Fig. 2-5
1. Receive the color bar pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (1) on the remote control.
The Fig. 2-6 appears on the display.
4. Press the channel button (4) on the remote control.
5. Press the VOL. UP/DOWN button on the remote control
until the horizontal line of the color bar comes to
approximate center of the CRT.
2-17: OSD HORIZONTAL
1. Receive monoscope pattern.
2. Using the remote control, set brightness and contrast to
normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (5) on the remote control.
The Fig. 2-2 appears on the display.
4. Press the channel button (4) on the remote control.
5. Press the VOL. UP/DOWN on the remote control until
the difference of A and B becomes minimum.
(Refer to Fig. 2-7)
2-18: WHITE BALANCE
Place the set with Aging Test for more than 15 minutes.
1.
2. Receive the color bar pattern.
Fig. 2-6
Activate the adjustment mode display of Fig. 1-1 and
3.
press the channel button (2) on the remote control.
The Fig. 2-8 appears on the display.
Adjust the adjustment mode display of Fig. 2-8 until the
4.
white color is loocked like a white.
[ TV ]
OSD H
A
1. AKB AUTO
2. R.BIAS
3. G.BIAS
4. B.BIAS
5. R.DRIVE
6. G.DRIVE
7. B.DRIVE
8. AGC AUTO 0. RETURN
B Fig. 2-7
Fig. 2-8