LG LRH7160D Series Owner's Manual page 67

NOTE
• ATM/POS Recording Information.
Option setting
Recording is started automatically
When the Transaction when the Transaction start data is
Start and Transaction End detected. When the Transaction
options are set. end data is detected, the recording
is stopped after post-alarm time.
Recording is started automatically
when the transaction data is
When the Transaction detected. When the transaction
Start and Transaction End data is not detected, the recording
option is not set. is stopped after post-alarm time
and the time you set in the Time
Out option.
Event Popup
• Spot Monitor: Select the event type for the spot monitor display
when the event is activated.
Mail
1. Click the [Setup] button.
2. Set the below options.
• Notification: Mark up to be notified the unit's operating
information according to notification settings by e-mail.
If notification option is not set, the other options cannot be
set.
- SMTP Server: Enter the SMTP Server address.
- SMTP Port: Enter the SMTP Port Number. Typically the
port used for SMTP is 25. However in some cases it is
better to change this port number for added flexibility
or security. You can edit this port between 1 and 65 535.
-
User Name: Enter the user name.
- Password: Enter the password.
• TLS: Mark up if you want to use the TLS (Transport Layer
Security) function.
- Mail Address (1 to 3): Enter the mail address.
You can input up to 3 e-mail addresses.
- Sender : Enter the sender.
• JPEG Attachment: Click the check box to send a mail which
want to attach a JPEG file.
NOTE
• The SMTP server, SMTP port no., user name or password
settings are optional. The DVR can send e-mail directly without
the use of an SMTP server or MTA (message transfer agent).
In certain cases all e-mail should be forwarded to a specific
SMTP server. Specify the server host name or IP address in
such a case. For more detail on SMTP setup, ask your network
administrator and/or mail service provider.
• [JPEG Attachment] option is operated when event of [Sensor
On], [Motion Detection] and [Text In] is occurred.
• In case of an IP Camera, ONVIF JPEG Snapshot feature must be
supported to attach a JPEG file.
3. Click the [OK] button to confirm the settings.
ATM/POS Recording Action
Notification
Mark up when you want to activate the selected option. If the
selected notification option is activate, notify the user about the
information of selected option by E-mail.
• Sensor On: Sends an e-mail when a sensor has occurred.
• Motion Detection: Sends an e-mail when an motion detection
has occurred.
• Text In: Sends an E-mail when the text input is detected.
• Admin PW Changed: Sends an e-mail when the administrator
password has been changed.
• Video Loss: Sends an e-mail when a video signal from the
camera has stopped because of a cable disconnection or
malfunction of a camera.
• Power On/Off: Sends an e-mail when power is on or off.
• Disk Full: Sends an e-mail when the HDD has fully recorded.
Buzzer
Mark up when you want to activate the selected option.
• Sensor: Makes a sound when a sensor occurs.
• Motion : Makes a sound when a motion is detected.
• Text: Makes a sound when the DVR detects text input .
• System: Makes a sound when a cooling fan is not activated or
the HDD has bad sector.
NOTE
• Data cannot be saved in HDD which is occurred bad sector.
But if HDD is installed more than 2 on this unit, data is saved in
other normal HDD.
• When HDD has bad hold, can not operate normally. Replace
the HDD immediately .
SNMP
1. Click the [Setup] button.
2. Set the below options.
• SNMP Version: Selects a SNMP version if SNMP is allowed to
access to this device.
• Port: Enter the number for SNMP port.
• Community String (V2 only): Specifies the SNMP management
community in which you want to enable this system (e.g.
lgecommunity or public).
• User (V3 only): Enter the security name for the SNMP.
• Authentication (V3 only): Select a mode for the SNMP
Authentication. (MD5 or SHA)
• Password (V3 only): Enter the password for the SNMP
Authentication.
• Privacy (V3 only): Select a privacy mode for the SNMP
Authentication. (DES or AES)
• Password (V3 only): Enter the password for the privacy mode.
• Trap IP Address: Specifies the IP address of the computer you
intend to use as your network management station and to
which SNMP traps will be sent.
• Trap Community String (V3 only): Specifies the SNMP trap
community in which you want to enable this system (e.g.
lgecommunity or public).
LG Network Client Program 67
5