Water Supply Connec on 9 Ice Maker Opera on 10 Tips & Care 10 Normal Opera ng Sounds 10 TROUBLESHOOTING & WARRANTY Ice Maker Fill Adjustment 11 Customer Service 11 Troubleshoo ng 12 Limited Warranty 13 PRODUCT REGISTRATION Thank you for purchasing our Haier product. This easy‐to‐use manual will Model Number guide you in ge ng the best use of your product. Remember to record the model and serial numbers. They are located on a label on Date of Purchase the ice maker. Staple your receipt to your manual. You will need it to obtain warranty service. PAGE 15 ● NOTES P/N 0060517641 Rev A ...
IMPORTANT SAFETY INSTRUCTIONS ! WARNING TO AVOID ELECTRICAL SHOCK, WHICH CAN CAUSE DEATH OR SEVERE PERSONAL INJURY, DISCONNECT THE POWER SUPPLY BEFORE CONNECTING A WATER SUPPLY LINE TO THE REFRIGERATOR. ! WARNING DO NOT PLACE FINGERS OR HAND ON THE AUTOMATIC ICE MAKING MECHANISM WHILE THE REFRIGERATOR IS PLUGGED IN. THIS WILL HELP PROTECT YOU FROM POSSIBLE INJURY AS WELL AS PREVENT INTERFERENCE WITH MOVING PARTS OF THE EJECTOR MECHANISM AND THE HEATING ELEMENT THAT RELEASES THE CUBES. PROFESSIONAL INSTALLATION IS RECOMMENDED. TO AVOID PROPERTY DAMAGE: Copper tubing is recommended for the water supply line. Water supply tubing should be 1/4". Plas c is not recommended since it greatly increases the poten al for water leaks. Do not install water supply tubing in areas where the temperature falls below freezing. Connect the ice maker to a drinkable water source that is not connected to a water so ening system. Chemicals from the so ener may damage the ice maker, causing it to malfunc on. SAVE THESE INSTRUCTIONS HOUSEHOLD USE ONLY PAGE 14 ● NOTES ...
− Replacement of house fuses or rese ng of circuit breakers. − Failure of the product if it is used for other than its intended purpose or used commercially. − Damage to product caused by accident, fire, floods or Acts of God. WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES. THIS LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR, INCLUDING Ice Maker Ice Bucket Water Supply Hex Head Screws THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Clamp Qty: 2 The remedy provided in this warranty is exclusive and is granted in lieu of all other remedies. This warranty does not cover incidental or consequen al damages, so the above limita ons may not apply to you. Some States do not allow limita ons on how long an implied warranty lasts, so the above limita ons may not apply to you. This warranty gives you specific legal rights, and you may have other rights, which vary, from state to state. Haier America Moun ng Screw User Manual Installa on New York, NY 10018 Washer Checklist PAGE 4 ● SET UP & CARE PAGE 13 ● TROUBLESHOOTING & WARRANTY P/N 0060517641 Rev A ...
TROUBLESHOOTING INSTALLATION INSTRUCTIONS 1. Move refrigerator away from wall and unplug. PROBLEM CAUSE/SOLUTION 2. Remove freezer shelf by li ing up and sliding it out of freezer compartment. Ensure that refrigerator is plugged in to power Freezer Shelf source Wire control arm is fully raised. See Page 9. Check that ice maker is plugged into electrical socket in rear of freezer compartment. See Pages 5‐6. No ice produced Water supply is turned off or disconnected. Disconnect refrigerator from power source, remove rear access cover, then check to see that water valve is plugged into wiring harness in rear bo om 3. Remove plas c plug above electrical socket by grasping firmly and pulling compartment. end of plug down. Check water connec ons on water valve. See Page 8. Adjust freezer temperature to colder se ng. See Refrigerator User Manual for instruc ons. Low/slow Check for leaks or kinks in water tubing on rear of ice produc on refrigerator. Increase water fill amount. See Page 11. Small ice cubes Increase water fill amount. See Page 11. Check that fill tube is aligned into fill cup on rear of ...
Page 6
2. Use a Phillips screwdriver to turn fill adjustment screw clockwise to DECREASE water fill amount. Turn screw counter‐clockwise to INCREASE water fill amount. Fill Adjustment Screw 3. Replace front cover of ice maker. 7. Re‐install electrical plug cover by pushing cover down on plug, inser ng tab CUSTOMER SERVICE into slot on rear cover and then snapping front prongs into square holes. IMPORTANT CUSTOMER SERVICE DO NOT RETURN THIS PRODUCT TO THE STORE SERVICIO If you have a problem with this product, please contact the Tab AL CLIENTE Haier Customer Sa sfac on Center at 1‐877‐337‐3639 Front Prong H o t l i n e DATED PROOF OF PURCHASE, MODEL NUMBER AND SERIAL 1-877-337-3639 Slot Square Hole NUMBER REQUIRED FOR WARRANTY SERVICE PAGE 11 ● TROUBLESHOOTING & WARRRANTY PAGE 6 ● SET UP & CARE P/N 0060517641 Rev A ...
Page 7
ICE MAKER OPERATION INSTALLATION INSTRUCTIONS CONT. 8. Posi on fill tube into slot in rear of ice maker fill cup. NOTE: It takes approximately 24 hours for the ice maker to produce ice. New plumbing may cause ice discolora on and poor flavor. Fill Tube Discard ice made in the first 24 hours. To stop the ice maker, li the wire arm un l it clicks and locks in the OFF Fill Cup (raised) posi on. The ice maker turns OFF automa cally when the ice container is full. If your model has an adjustable freezer shelf, place the shelf so that when the ice container is full, the ice will hit the wire control arm. TIPS & CARE Water quality determines ice quality. Do not connect the ice maker to water that is so ened. Chemicals from a malfunc oning so ener can damage the ice maker. 9. Hang ice maker from moun ng posts. Ice stored too long may develop an odd flavor. Empty the container and make sure the wire arm is in the ON (lowered) posi on. The ice maker will then produce ice. ...
Page 8
INSTALLATION INSTRUCTIONS CONT. WATER SUPPLY CONNECTION 13. Re‐install freezer shelf on lowest rail as shown and place ice bucket under ! WARNING the ice maker. Raise wire control arm on ice maker to OFF posi on. Wire Control Arm This water supply installa on is not covered under warranty by the refrigerator or ice maker manufacturer(s). Follow these instruc ons carefully to minimize the risk of expensive water damage. Supplies Required for Installa on: Access to a household cold water line with water pressure between 20psi and 120psi. Lowest Rail A water supply line made of 1/4‐inch Outside Diameter, copper tubing. To determine the length of the copper tubing needed, you will need to measure the distance from the ice maker water valve at the back of the refrigerator to your cold water line. Then add approximately 7 feet for the refrigerator to be moved out for cleaning and service. A shut‐off valve to connect the water supply line to your household water system. NOTE: Do not use a self‐piercing type shut‐off valve. A compression nut and ferrule (sleeve) for connec ng the water supply line to the ice 14. Locate water valve on rear of refrigerator. Valve protrudes slightly through maker inlet valve. See page 4 for picture. rear compartment cover. 1. Turn off water supply at shut‐off valve. 2. Connect copper water supply line to household water system. 3. Turn ON water supply and ...