75 ohm external antenna terminal for VHF/UHF The ( ) SRS (SOUND RETRIEVAL SYSTEM) is manu- factured by Sony Corporation under license from SRS Labs, Supplied accessories Inc. It is covered by U.S. Patent No. 4,748,669. Other U.S. Remote control RM-Y154 and foreign patents pending.
SONT D'UNEIMPORTANCE CRITIQUE POUR LA SECURITE DU FONCTIONNEMENT. THESE COMPONENTS WITH SONY PARTS WHOSE PART NE LES REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE NUMERO DE NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN PIECE EST INDIQUE DANS LE PRESENT MANUEL OU DANS DES SUPPLEMENTS...
Page 4
KV-32V68/35V68 SAFETY CHECK-OUT After correcting the original service problem, perform the LEAKAGE TEST following safety checks before releasing the set to the The AC leakage from any exposed metal part to earth ground and customer: from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampere).
Connecting and Installing the TV Welcome! Precautions Using This Manual Making Connections Thank you for purchasing the Sony Trinitron ® Safety This manual is divided into five major sections. Color TV. Before reading this manual, check the We recommend that you review the contents of Refer to the table below, it will direct you to the diagram suitable to the components you will be •...
Page 6
Connecting and Installing the TV (continued) DBS Connections For optimum picture quality, use Cable/Antenna (Rear of TV) Additional Connections VIDEO 1 VIDEO 3 S VIDEO instead of the yellow A/V S VIDEO cable. S Video does not provide sound, MONITOR AUDIO (VAR/FIX) (Rear of TV) Connecting a DBS (Direct Broadcast...
Page 7
• To reset your TV to factory settings, turn the TV CH +, CH – or VOL +. that all available channels will be broadcasting and available in your area, please contact the Sony on. Then, while pressing the RESET button on receivable.
Using Your New TV (continued) POWER MUTING VTR/ CABLE DBS/ SYSTEM VTR/ FUNCTION DBS/ CABLE VCR+ Using the GUIDE Plus+ Feature Using the GUIDE Plus+ Feature TV/VTR FREEZE SWAP POSITION AUDIO TV/VIDEO – SLEEP DISPLAY TV/VIDEO The video window allows you to view a program while in the Program Grid. Pressing the button while using the GUIDE Plus+ Video Window The GUIDE Plus+ feature allows you to see local...
Page 9
Using Your New TV (continued) Press v to highlight the desired program (in Press to select the program. Learning to schedule viewing Learning to view a program JUMP Press the blue action button to select this case "Spin City"). and recording using the using the GUIDE Plus+ feature WATCH.
VCR mode. Your VCR power will remain on. the GUIDE Plus+ feature, the same picture will other errors instead of intended text. appear in both the main picture and window SYSTEM The SYSTEM OFF button allows you to power off all Sony equipment at once. picture.
Page 11
Using Your Menus Press V or v to move to the desired option. When you are finished making changes to the Learning menu selection Quick start to the menus The VIDEO menu allows you to make adjustments to your picture settings. VIDEO selected menu, choose MENU to return to the...
Page 12
Using Your Menus (continued) Using the TIMER menu DAYLIGHT Set DAYLIGHT SAVING time before setting the clock. Using the SET UP menu SAVING Spring: Select YES to compensate for Daylight Saving Time. CHANNEL With the CHANNEL SET UP menu open: CHANNEL SET UP Press V or v to access a feature, then press TIMER...
(see page 31) If, after reading these operating instructions, you have additional questions related to the use of your Sony television, please call our Direct Response Center at 1-800-222-SONY • Use AUTO PROGRAM to add receivable channels that (7669) (U.S. residents only) or (416) 499-SONY (7669) (customers in Canada only)
KV-32V68/35V68 2-5. PICTURE TUBE REMOVAL WARNING -- Before removing anode-cap: Four screws (Tapping screw 7) G board High voltage remains in the CRT even after the power is disconnected. Chassis To avoid electrical shock, discharge CRT before attempting to remove the anode- Picture tube cap.
SECTION 3 KV-32V68/35V68 SET-UP ADJUSTMENTS The following adjustments should be made when a Perform the adjustments in order as follows: complete realignment is required or a new picture tube is installed. Beam Landing 2. Convergence These adjustments should be performed with rated Focus power supply voltage unless otherwise noted.
KV-32V68/35V68 3-2. CONVERGENCE Preparation: • Before starting, perform FOCUS, V. LIN and V. SIZE adjustments. • Set BRIGHTNESS control to minimum. • Input dot pattern. (1) Vertical and Horizontal Static Convergence Operation of BMC (Hexapole) Magnet The respective dot positions resulting from moving each 1.
Increase the voltage gradually and confirm that the above steps. holdown works (raster disappears) at lower than the voltage recorded in Step 3. Lower than 26.95 + (-0.05) V DC (KV-32V68), 22.05 + (-0.05) V DC (KV-35V68). At AC input: 120.0 ± 2.0 VAC — 20 —...
KV-32V68/35V68 SECTION 5 CIRCUIT ADJUSTMENTS ELECTRICAL ADJUSTMENT BY REMOTE COMMANDER Use Remote Commander (RM-Y154) to perform the following circuit adjustments: NOTE : Test Equipment Required: 1. Pattern Generator 2. Frequency Counter 3. Digital Multimeter 4. Audio OSC (1) Method of Setting the Service...
Page 22
0:-7 Steps, 15: +8 steps STRE Sub Treble 0-15 Fix by model 0:-7 Steps, 15: +8 steps AP MM1313 AUSW Audio Att Sw 0:-6dB, 1:0dB (Only for VIDEO input) **AVERAGE DATA MODEL GROUPINGS: 32" A: KV-32V68 35" B: KV-35V68 — 22 —...
Page 23
CC Data start delay 0-31 Fixed value only CCDS CC Caption data threshold 0-31 Fixed value only CHMK CC P8_HMASK 0-63 Hmask CHSY CC P8_HSYC 0-255 Hsyc **AVERAGE DATA MODEL GROUPINGS: 32" A: KV-32V68 35" B: KV-35V68 — 23 —...
Page 24
0-255 Fix by model See ID map ID-7 ID-7 (Special Models/etc) 0-255 Fix by model See ID map **AVERAGE DATA MODEL GROUPINGS: 32" A: KV-32V68 35" B: KV-35V68 SERVICE Note: Items 1-124 show adjustment order (5) Feature ID Map ID 0 ID 1...
Page 25
KV-32V68/35V68 SUB BRIGHT ADJUSTMENT (SBRT) 10. Return the following back to normal after adjustment. 1. Set to Service adjustment Mode. PICTURE ... MAX 2. Input a gray scale pattern signal.
Page 26
KV-32V68/35V68 PIN AMP (PAMP) V. SIZE ADJUSTMENT ( VSIZ) 1. Input a cross-hatch signal. 2. Set to Service adjustment mode. 3. Select VSIZ with PIN PHASE (PPHA) 4. Adjust with for the best vertical size. 5. Write into the memory by pressing then V.
6-3. CIRCUIT BOARDS LOCATION KV-32V68 KV-35V68 6-4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • All voltages are in V. • All capacitors are in µF unless otherwise noted. pF : µµF 50WV or less are not S : Measurement impossibility.
Page 28
Q3301 Q3314 TO WA BOARD PIN 1 O-TVBLK CN941 KV-35V68 BUFF VM OUT Q357 PIP ENCODE TO WB BOARD PIN 1 CHROMA DECODE O-BBE CN2941 KV-32V68 BOARD (2/2) VTIM MAIN.V.P M.VSYNC CN271 PIN6 BOARD RM CN MAIN.H.P I-HP M.HSYNC (2/2)
Page 29
VM DRIVE BOARD MAIN-Y YOUT1 GEMSTAR (1/2) Q2943-2945 Q2965,2966 Q2946,2947 LINK CN270 MAIN-C COUT1 FROM (2/2) IC102 IC100 FOR KV-32V68 ONLY CN1804 FROM IC103 AUDIO AUDIO (SYSTEM CONTROL) FBT 15V-P 15V-P SUB-V/IR BLASTER VOUT2 BOARD SRS/AUDIO PROCESSOR PROCESSOR GLINK (1/2) VELOCITY MOD.
Page 30
TO UV BOARD CN3001 TO P BOARD CN1802 CN270 CN271 TO KG BOARD CN1231 TO HV BOARD CN2231 TO UV BOARD CN262 CN264 CN3301 :BTOB-P :BTOB-P :BTOB-P CN801 CN802 :S-MICRO TO HS BOARD CN2102 CN1801 HS BOARD CN2101 TO C BOARD CN1001 :S-MICRO CN1803...
Page 32
A BOARD IC VOLTAGE LIST IC001 IC351 volt volt IC501 volt -16.1 0.08 0.07 -15.9 13.0 IC561 volt IC002 volt 11.8 -14.0 -16.2 -0.7 12.8 All voltages are in V...
Page 34
AV BOARD TRANSISTOR AV BOARD IC VOLTAGE LIST VOLTAGE LIST IC101 IC1902 Q101 volt volt Q103 Q104 Q105 11.0 Q106 IC1901 Q1901 volt Q1902 All voltages are in V All voltages are in V...
Page 35
AV BOARD IC VOLTAGE LIST IC1902 volt -0.1 IC1901 volt All voltages are in V...
Page 36
TO AV BOARD CN102 VIDEO VIDEO CN3502 2-DET VIDEO IC3503 L3504 L7805CV C3548 VIDEO M-IN1 5V REG M-IN3 B:CHIP M-OUT IC3502 C3553 C3503 C3545 CXD2073S 0.01 C3523 COMB FILTER B:CHIP 0.01 B:CHIP B:CHIP PLVD C3544 STBY 5V C3543 C3522 R3507 2.2k R3508 R3578...
B BOARD IC VOLTAGE LIST B BOARD TRANSISTOR IC3501 IC3502 IC3503 VOLTAGE LIST volt volt volt Q3501 Q3502 Q3503 All voltages in V Q3504 Q3505 Q3506 Q3507 Q3509 Q3510 Q3516 Q3555 All voltages are in V...
Page 41
BOARD JW2001-JW2008 BOARD BOARD CN1001 CN1231 SIRCS FRONT STBY FRONT FRONT-SW TIMER FRONT FRONT LUMIPON POWER FRONT CN2102 CN2101 :S-MICRO BOARD JW2231-JW2237 B-#SV6764<GEM..>HS..
Page 42
D641 R666 D10SBS4F 0.47 :FPRD AUDIO-RECT 2 4 V B O A R D C691 C N 1 6 4 1 B O A R D C690 R674 R667 1000p C N 1 0 6 0.47 1000p 500V JW(5) 500V :FPRD R603 R670...
G BOARD TRANSISTOR VOLTAGE LIST G BOARD IC VOLTAGE LIST Q622 IC601 Q644 11.1 volt Q645 11.1 Q646 Q647 11.1 -153 Q648 0.09 All voltages are in V -151 G BOARD TRANSISTOR IC622 VOLTAGE LIST volt Q621 All voltages are in V IC641 volt 11.1...
The components identified by shading and "¡ ¡ ¡ ¡ ¡ " mark are critiques pour la securite. Ne les remplacer que par une piece critical for safety. Replace only with specified part number. portant le numero specifie. 7-2. PICTURE TUBE (KV-32V68 only) REF.NO. PART NO. DESCRIPTION REMARK...
Page 61
KV-32V68/35V68 Note: Note: Les composants identifies per un trame et une marque The components identified by shading sont critiques pour la securite. Ne les remplacer and mark are critical for safety. Replace only with par t number specified. que par une piece portant le numero specifie.
Page 62
KV-32V68/35V68 Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. sont critiques pour la securite. Ne les remplacer Replace only with part number specified. que par une piece portant le numero specifie.
Page 65
KV-32V68/35V68 A AV Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. sont critiques pour la securite. Ne les remplacer Replace only with part number specified. que par une piece portant le numero specifie.
Page 69
KV-32V68/35V68 Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. Replace sont critiques pour la securite. Ne les remplacer que par une piece portant le numero specifie.
Page 70
KV-32V68/35V68 G HS HV K Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. sont critiques pour la securite. Ne les remplacer que par une piece portant le numero specifie.
Page 71
KV-32V68/35V68 K KG Note: Note: The components identified by shading Les composants identifies per un trame et une marque and mark are critical for safety. sont critiques pour la securite. Ne les remplacer que Replace only with part number specified.