Sony TRINITRON KV-32V68 Service Manual page 6

Connecting and Installing the TV (continued)
DBS Connections For optimum picture quality, use
S VIDEO instead of the yellow A/V
cable. S Video does not provide sound,
Connecting a DBS (Direct Broadcast
your audio connectors must still be
Satellite) receiver
connected.
1
Connect the cable from your satellite antenna
to SATELLITE IN on your DBS receiver.
2
Connect your cable or antenna to VHF/UHF
on your TV.
3
Using A/V connectors, connect AUDIO and
VIDEO OUT on your DBS receiver to
AUDIO and VIDEO IN on your TV.
Connecting a DBS (Direct Broadcast
Satellite) receiver and a VCR
1
Connect the cable from your satellite antenna
For superior picture quality, use an A/V cable
to SATELLITE IN on your DBS receiver.
instead of the VHF/UHF connection.
2
Connect your cable or antenna to VHF/UHF
IN on your VCR.
1
3
4
Using a coaxial connector, connect VHF/UHF
OUT on your VCR to VHF/UHF on your TV.
4
Using A/V connectors, connect AUDIO and
SATELLITE IN
VIDEO OUT on your DBS receiver to AUDIO
AUDIO R AUDIO L VIDEO
and VIDEO IN on your VCR.
LINE OUT
5
Using A/V connectors, connect AUDIO and
DBS receiver
VIDEO OUT on your VCR to AUDIO and
VIDEO IN on your TV.
Pressing TV/VIDEO on the
remote control will allow you
to view from the DBS or VCR.
6
Connecting and Installing the TV (continued)
Connecting an A/V receiver
1
Using A/V cables, connect TV OUT on your
TV to TV IN on your A/V receiver.
2
Using a single video connector, connect
MONITOR OUT on your A/V receiver to
VIDEO 1 IN on your TV.
Note
• When you are in a video mode (VIDEO 1, 2, or 3),
you will not be able to access the GUIDE Plus+
feature.
Connecting two VCRs for editing
MONITOR OUT gives you the ability to use a
second VCR to record a program being played
by the primary VCR or to perform tape editing
and dubbing.
1
Connect the VCR intended for playback using
the setup instructions on page 5 of this
manual.
2
Using A/V connectors, connect AUDIO and
VIDEO IN on your VCR intended for
recording to MONITOR AUDIO and VIDEO
OUT on your TV.
8
Cable/Antenna
VIDEO 1 VIDEO 3
AUX
2
TO
CONVERTER
VHF/UHF
DBS receiver
1
SATELLITE IN
VHF/UHF
AUDIO R AUDIO L VIDEO S VIDEO IN
Satellite
OUT
antenna LINE OUT
cable
3
VMC-810S/820S (not supplied)
Cable/Antenna
VMC-810S/820S (not supplied)
VIDEO 1 VIDEO 3
AUX
TO
CONVERTER
VCR
VHF/UHF
VHF/UHF
S VIDEO 2
AUDIO R AUDIO L VIDEO
S VIDEO IN
OUT VHF/UHF
LINE IN
IN
OUT
LINE OUT
3
5
VMC-810S/820S (not supplied)
2
VMC-10HG/30HG (not supplied)
VIDEO (yellow)
IN
(Rear of TV)
VIDEO 1 VIDEO 3
OUT
S VIDEO
MONITOR AUDIO
TV
(VAR/FIX)
VIDEO
L
(MONO)
AUDIO
R
S-LINK G-LINK S-LINK
VIDEO (yellow)
AUDIO-L (white)
AUDIO-R (red)
1
VMC-810S/820S (not supplied)
You should not change video
inputs while editing using
MONITOR OUT.
IN (Rear of TV)
VIDEO 1 VIDEO 3
OUT
S VIDEO
MONITOR AUDIO
TV
(VAR/FIX)
VIDEO
L
(MONO)
AUDIO
VCR (for playback)
R
AUDIO R AUDIO L VIDEO
OUT S-LINK G-LINK S-LINK
LINE
IN
OUT
VIDEO (yellow)
1
AUDIO-L (white)
AUDIO-R (red)
2
VMC-810S/820S (not supplied)
VMC-810S/820S (not supplied)
IN (Rear of TV)
Additional Connections
S VIDEO OUT
MONITOR AUDIO
TV (VAR/FIX)
The following connections are for accessories
VIDEO
that will enhance your viewing options.
L
(MONO)
AUDIO
R Connecting a DVD Player
S-LINK G-LINK S-LINK
1
Using audio connectors, connect AUDIO-R
and AUDIO-L OUT from LINE OUT on your
AUDIO-R (red)
DVD to AUDIO-R and AUDIO-L IN from
AUDIO-L (white)
VIDEO (yellow) VIDEO IN on your TV.
2
Connect S-Video from your DVD player to
your TV.
Connecting an audio system
(Rear of TV)
IN
For enhanced sound, connect your audio system
S VIDEO OUT
MONITOR AUDIO
TV (VAR/FIX)
to your TV.
VIDEO
L
1
(MONO) Using AUDIO connectors, connect AUDIO
AUDIO
R
OUT on your TV to one of the unused line
S-LINK G-LINK S-LINK inputs (e.g. TV, AUX, TAPE 2) on your stereo.
2
AUDIO-R (red) Set your stereo to the chosen line input. Refer
AUDIO-L (white)
to page 29 of this manual for additional audio
VIDEO (yellow)
setup instructions.
Connecting a camcorder
This connection is convenient for viewing a picture
directly from your camcorder.
Using A/V connectors, connect AUDIO and VIDEO
OUT on your camcorder to AUDIO and VIDEO IN
on your TV.
A/V outputs
Connection can also be made directly to your A/V
input located on the rear of your TV.
Note
A/V receiver
• If you are connecting a monaural camcorder,
HRD
connect only the single white audio output to the
left input on your TV.
A/V inputs
Connecting the IR Blaster (G-Link)
You must connect your IR Blaster to automatically
control your VCR and/or cable box with the GUIDE
Plus+ feature.
1
Connect the IR Blaster to the TV's G-Link
jack.
2
Place the IR Blaster on top of (or below) and
overhanging the front of the VCR and/or
cable box, about 1/2" to 1". For best results,
place the IR Blaster directly above (or below)
the VCR's and/or cable box's IR receiving
VCR (for recording)
area.
AUDIO R AUDIO L VIDEO
OUT
LINE 3
IN Set the manufacturer and code type of your
IN
VCR/cable box, using the GUIDE PLUS+
SET UP menu (see page 31). This code must
be set for the GUIDE Plus+ feature to
function properly.
IN
(Rear of TV)
VIDEO 1 VIDEO 3
2
S VIDEO
TV
(Rear of DVD player)
VIDEO
L
LINE OUT (MONO)
AUDIO
AUDIO R AUDIO L VIDEO S VIDEO
R
1 S-LINK G-LINK
AUDIO-R (red)
AUDIO-L (white)
S Video
Connection
VMC-810S/820S (not supplied)
IN
(Rear of TV)
VIDEO 1 VIDEO 3
1
S VIDEO OUT
MONITOR AUDIO
TV
(VAR/FIX) AUDIO-L
RK-74A
(white)
VIDEO
(not supplied)
L
(MONO)
AUDIO
R
AUDIO-R
S-LINK G-LINK S-LINK (red)
Line
input
2
If you have an S VIDEO equipped (Front of TV)
camcorder, you can use an S Video
S VIDEO VIDEO 2 INPUT
cable for optimum picture quality.
VIDEO L(MONO)-AUDIO-R
STAND BY
TIMER
STEREO
S VIDEO VIDEO L (MONO)
VIDEO 2 INPUT
VIDEO (yellow)
AV output
VMC-810S/820S
(not supplied)
(Rear of TV)
IN
VIDEO 1 VIDEO 3
S VIDEO OUT
TV MONITOR AUDIO
(VAR/FIX)
VIDEO
L
(MONO)
AUDIO
R
OUT AUDIO R AUDIO L VIDEO
LINE
S-LINK G-LINK S-LINK IN OUT
IR Blaster
OUT
IN
OUT
MONITOR AUDIO
(VAR/FIX)
S-LINK
HRD
7
-AUDIO-R
AUDIO-R (red)
AUDIO-L (white)
VCR
S VIDEO
Cable Box
9