Video Plus+ Timer Programming - JVC DR-MV1B Instructions Manual

Filename [DR-MV1SEK_07VCR Operation.fm]
DR-MV1SEK_00.book Page 56 Thursday, April 15, 2004 3:30 PM
OPERATIONS ON VCR DECK
56
EN
VIDEO Plus+ Timer Programming
®
You can programme this unit to timer-record as many as
8 programmes.
With the VIDEO Plus+ system, timer programming is greatly
simplified because each TV programme has a corresponding code
number which your unit is able to recognise.
You can use the remote control to enter the PlusCode number.
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
VCR TIMER (#)
VCR/DVD
1
4
7
CANCEL (&)
VIDEO Plus+
ENTER
REC MODE
1
Load a cassette with the record safety tab intact.
2
Press VCR/DVD repeatedly so that the VCR lamp lights up on
the unit.
3
Press VIDEO Plus+ to access the VIDEO Plus+ screen.
4
Press the number keys to enter
the PlusCode number of a programme
you wish to record, then press
ENTER.
If you have made a mistake, press
CANCEL (&) and input the correct
number before you press ENTER.
If the number you entered is invalid,
"ERROR" appears on the TV screen
and "Err" appears on the front display
panel. Press CANCEL (&) and input a valid PlusCode number.
5
The PlusCode number you entered
and the matching timer-recording
information are displayed on the TV
screen. Check the programme data.
To cancel this setting, press VIDEO
Plus+ or PROG/CHECK.
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see "VIDEO Plus+
set the Guide Program number correctly.
Page 56
SAT
2 3
0 – 9
5 6
8 9
0
PROG/CHECK
rtw e
RETURN
[0 – 9] [ENTER]
[&] : DELETE
[VIDEO PLUS+] : EXIT
VIDEO PLUS+ SYSTEM
® System Setup" ( pg. 83) and
6
Press REC MODE to select the desired recording mode. Or
press w e to select "SP/LP", then press rt to select the desired
recording mode.
7
Press the number keys to set "VPS/PDC" to "ON" or "OFF".
* VPS (Video Programme System) recording is not currently available
in the U.K. and not possible with this unit.
8
Press ENTER to complete timer programming.
To programme another timer, repeat steps 3 – 8.
If "PROGRAM OVERLAPPED" appears on the TV screen, see
page 58.
9
Press VCR TIMER (#) to engage the unit's timer mode. The
VCR timer lamp lights up on the unit and the DVD deck is
automatically selected. Press 1 to turn off the unit. When the
DVD deck is in timer standby mode, the unit is automatically turned
off.
To disengage the timer mode, press VCR TIMER (#) again.
IMPORTANT:
If you have moved to a different area or if a broadcasting station's
programme number has been changed, the wrong programme
number will be displayed on the VIDEO Plus+ programme screen in
step 5. When this happens, set the correct Guide Program number
for that station. ( pg. 83, "VIDEO Plus+
NOTES:
To Timer-Record Weekly Or Daily Serials:
— in step 5, press number key "9" for weekly serials or number key
"8" for daily serials (Monday — Friday). Either "WEEKLY" or "DAILY"
appears on the TV screen. Pressing the button again makes the
corresponding indication disappear.
You can programme this unit to timer-record as many as 8
programmes. If you try to programme the unit to record a ninth,
"PROGRAMME FULL" appears on the TV screen and "FULL"
appears on the front display panel. To record the extra programme,
you must first cancel any unnecessary programmes. (
To record the programmes received by satellite receiver, record on
the DVD discs. For details, refer to "VIDEO Plus+
Programming" ( pg. 45).
Masterpage:Left+
® System Setup")
pg. 58)
® Timer
April 15, 2004 1:27 pm