Panasonic AG-EC4G Operating Instructions Manual page 6

Parts and their functions
16.W.BAL switch
PRST :
This will read out the preset value of the white
balance stored in the camera recorder.
Set to this position if there is no time to adjust the
white balance.
A or B :
This will read out the value stored in the white
balance A or B in the camera recorder.
When the 17. AWB/ABB (auto white balance/auto
black balance adjustment) switch is set to the AWB
position, the white balance is automatically adjusted,
and the value adjusted is stored in memory A or
memory B.
The white balance value corresponding to the FILTER
control position can also be stored in the memory by
setting FILTER INH to OFF. For further details, refer to
the respective pages in the Operating Instructions of
the camera recorder being used.
17.AWB/ABB (auto white balance/auto black
balance adjustment) switch
AWB: Set here for the white balance to be adjusted
automatically.
When the 16. W.BAL switch is set to A or B at
this time, the value to which the balance was
adjusted will be stored in memory A or memory
B.
ABB: Set here for the black balance to be adjusted
automatically. The value to which the balance
was adjusted will be stored in a dedicated
memory.
18.AWB/ABB LED
LED lighted:
Auto white balance / auto black balance in progress.
LED dark:
Auto white balance / auto black balance completed.
LED stops blinking and goes off:
Auto white balance / auto black balance error.
19.SAVE switch
This is a switch to select either to store or not to store
the settings made by the unit into the camera recorder.
ON: Settings made by the unit are stored into the
camera recorder.
OFF: Settings made by the unit are not stored into the
camera recorder. The settings set by the unit
will not be reflected and the previous status will
be restored when the power of the unit or the
camera recorder is turned off.
20.MENU switch
This displays the menus at the VIDEO OUT connector.
(Continued)
21.SHUTTER switch
This is used to switch operation of the shutter.
OFF: Turning off the shutter operation.
FIX: Turning on the fixed shutter mode.
S.S: Turning on the synchro scan mode.
When the 26. AUTO IRIS switch is ON and the menu is
set not displayed, the shutter speed is set by using 22.
SETUP dial. The value of shutter speed is displayed on
the 30. Number display LED.
22.SETUP dial
This is used to set the SETUP menus. After a menu
has been selected using the dial, press the dial to enter
it.
23.PAINTING GAIN knob
This is the R/B/Gain volume.
24.PAINTING ENABLE switch
It enables operation by the PAINTING gain and black
volume.
25.PAINTING BLACK knob
This is the pedestal volume for the R/G/B.
26.AUTO IRIS switch
AUTO IRIS ON/OFF switch
<Note>
Set the lens manual/auto selector switch to AUTO.
27.IRIS knob
When the 26. AUTO IRIS switch is ON, this control
adds the control value to, or subtracts it from, the IRIS
LEVEL on the user menu. This addition or subtraction
is performed over a range of -2 steps to +2 steps.
When the 26. AUTO IRIS switch is OFF, it is used to
adjust the iris finely.
28.EXT INDICATOR
This lights when a lens extender is used.
29.M.PED knob
This is used to set the master pedestal.
30.Number display LED
The iris value and the gain, shutter speed or filter
positions are displayed on this LED. Normally, the iris
value is shown but when the gain value, shutter speed
or filter position has been changed, the respective
value is displayed.
<Note>
When the 35. SHUTTER SPEED INDICATOR is ON,
the ¢¢¢¢ part of the shutter speed value 1/¢¢¢¢ is
displayed.
31.CHECK switch
The gain value, shutter speed, filter position and iris
value are displayed in this order on the number display
LED by pressing this switch. The iris display is restored
after a prescribed period of time has elapsed.
E-5