Hitachi CG 24EBS Handling Instructions Manual
Grass trimmer/ brush cutter
Hide thumbs
Also See for CG 24EBS:
- Handling instructions manual (140 pages) ,
- Service manual (88 pages) ,
- Handling instructions manual (72 pages)
Advertisement
Quick Links
Download this manual
See also:
Service Manual
Grass Trimmer/Brush Cutter
Model CG 24EBS (SL) / CG 24EBS (S)
CG 24EBD (SL) / CG 24EBD (SLN)
CG 27EBS (SL) / CG 27EBS (S)
CG 27EBD (SL) / CG 27EBD (SLN)
Handling instructions
Note:
Before using this machine, carefully read through these HANDLING INSTRUCTIONS to ensure
effi cient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as
an important reference when using this machine.
CG24EBS (SL)
Advertisement
Related Manuals for Hitachi CG 24EBS
Summary of Contents for Hitachi CG 24EBS
- Page 1 Grass Trimmer/Brush Cutter Model CG 24EBS (SL) / CG 24EBS (S) CG 24EBD (SL) / CG 24EBD (SLN) CG 27EBS (SL) / CG 27EBS (S) CG 27EBD (SL) / CG 27EBD (SLN) Handling instructions CG24EBS (SL) Note: Before using this machine, carefully read through these HANDLING INSTRUCTIONS to ensure effi...
-
Page 2: Table Of Contents
MEANINGS OF SYMBOLS NOTE: Some units do not carry them. Symbols WARNING The following show symbols used for the machine. Be sure that you understand their meaning before use. Choke - Run position (Open) It is important that you read, fully understand and observe the following safety precautions and warnings. -
Page 3: What Is What
WHAT IS WHAT Since this manual covers several models, there may be some diff erence between pictures and your unit. Use the instructions that apply to your unit. Fuel cap 2. Throttle trigger 3. Starter handle 4. Cutting attachment guard 5. -
Page 4: Warnings And Safety Instructions
○ Keep others away when making carburetor adjustments. ○ Use only genuine Hitachi replacement parts as recommended Unit/machine safety by the manufacturer. ○ Inspect the entire unit/machine before each use. Replace damaged parts. -
Page 5: Specifications
CAUTION Do not disassemble the recoil starter. You may get a possibility of personal injury with recoil spring. SPECIFICATIONS CG24EBS CG24EBD Model (SL) (SL) (SLN) Engine Displacement (cm 23.9 23.9 23.9 23.9 Spark plug NGK BMR7A NGK BMR7A NGK BMR7A NGK BMR7A Idling speed (min 2800 –... -
Page 6: Assembly Procedures
CG27EBS CG27EBD Model (SL) (SL) (SLN) Engine Displacement (cm 26.9 26.9 26.9 26.9 Spark plug NGK BMR7A NGK BMR7A NGK BMR7A NGK BMR7A Idling speed (min 2800 – 3200 2800 – 3200 2800 – 3200 2800 – 3200 Speed of output shaft (min 7600 7600 7600... -
Page 7: Connect Stop Cords. (Fig
Installation of handle WARNING Always use a barrier bar (6) and shoulder harness with the loop handle. (Fig. 3) Fig. 6 Fig. 3 Attach the handle to the drive shaft tube with the angle towards the engine. Fig. 7 Adjust the location to the most comfortable position before operation. - Page 8 Fig. 13 ○ The cutting head must be securely mounted to the unit’s gear case. ○ For outstanding performance and reliability, always use Hitachi nylon cutting line. Never use wire or other materials that could become a dangerous projectile. ○ If the cutting head does not feed cutting line properly, check that the nylon line and all components are properly installed.
-
Page 9: Operating Procedures
○ Use genuine two-cycle oil or use a mix between 25:1 to 50:1, Installation of cutting blade (Fig. 17) please consult the oil bottle for the ratio or Hitachi Authorized (If so equipped) Service Centers. When installing a cutting blade, make sure that there are no cracks ○... - Page 10 Fueling 3. Pull recoil starter briskly, taking care to keep the handle in your grasp and not allowing it to snap back. (Fig. 22) WARNING ○ Always shut off the engine before refueling. ○ Slowly open the fuel tank, when fi lling up with fuel, so that possible over-pressure disappears.
-
Page 11: Maintenance
Stopping (Fig. 27) If the cutting attachment still rotates after idle speed adjustment, Decrease engine speed and run at an idle for a few minutes, then contact Hitachi Authorized Service Centers. turn off ignition switch (24). NOTE Standard Idle rpm is 2800 – 3000 min... - Page 12 Cleaning the air fi lter Open the air fi lter cover and the fi lter (29). Rinse it in warm soap suds. Check that the fi lter is dry before reassembly. An air fi lter that has been used for some time cannot be cleaned completely. Therefore, it must regularly be replaced with a new one.
- Page 13 ○ Use a sharp blade. A dull blade is more likely to snag and thrust. Replace the fastening nut if it is damaged and hard to tighten. ○ When replacing blade, purchase one recommended by Hitachi, with a 25.4 mm (one inch) fi tting hole.
- Page 14 List of recommended accessories Specifi cation LOOP HANDLE BIKE HANDLE MULTI PURPOSE Type Name NYLON HEAD CH-100 ● ● ● ● ● ● (W/NYLON LINE) 4” Pre-Cut Line 2.2 – 3.0 NYLON HEAD ● ● ● ● ● ● CH-100 NYLON HEAD CH-300 ●...
-
Page 15: Troubleshooting
TROUBLESHOOTING Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your dealer or the Hitachi Authorized Service Center. Condition Cause Remedy Fuel tank is empty or fuel level is low... - Page 16 Set the choke lever to START position to stop the engine Engine does not stop Stop switch failure Cease use immediately and contact Hitachi Authorized Service Centers Engine stops when throttle is closed Idle speed is too low Contact Hitachi Authorized Service Centers...
- Page 24 Hitachi Koki Co., Ltd. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. E99254613 NA Printed in China...