Related Manuals for LG 3828W5U0492
Summary of Contents for LG 3828W5U0492
-
Page 1: Microwave Oven
삼 흥 정 판 MICROWAVE OVEN INSTALLATION INSTRUCTIONS PLEASE READ AND SAVE THESE INSTALLATION INSTRUCTIONS. http://us.lgservice.com P/NO.: 3828W5U0492... -
Page 2: Your Safety First
• Proper installation is the installer's responsibility! – Read the entire manual before you begin. The Model number label is located on the front of oven, behind doon See Figure 1. Mounting plate is located on back side of microwave oven. See Figure 2. - Page 3 – DO NOT place objects between the microwave oven front face and the door. – DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door. – DO NOT operate the microwave oven if it is damaged.
- Page 4 – ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud. – DO NOT mount the microwave oven to an island or peninsula cabinet. – BE SURE the upper cabinet and rear wall structures are able to support 150 lbs., plus the weight of any items you place inside the oven or upper cabinet.
-
Page 5: Parts, Tools, Materials
PARTS, TOOLS, MATERIALS THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector (for roof venting or wall venting installation) Not Actual Size (2 pieces must be assembled as shown) One power cord clamp bushing - Actual Size (for the cord hole in a metal upper cabinet) Four 1/4"... - Page 6 PARTS, TOOLS, MATERIALS You will need the following tools and materials for the installation: Carton or other heavy material for covering the counter top. Clear Tape (for taping the templates to the wall) Saber Saw (for cutting vent holes for roof or wall venting) Phillips Screwdriver Pencil...
-
Page 7: Step 1: Prepare The Electrical Connections
1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 5. NOTE: The outlet should be on a circuit dedicated to the microwave oven (120V, 60 Hz., AC only) with a 15 or 20A fused electrical supply. IMPORTANT: If you do not have the proper wall outlet, you MUST have one installed by a qualified electrician. -
Page 8: Step 2: Prepare The Venting System
STEP 2: PREPARE THE VENTING SYSTEM NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 10, page 9. THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways. Do NOT vent into a wall cavity, an attic, or an unused area. - Page 9 Standard Fittings NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper’s sticking. Duct Length The total length of the duct system, including straight duct, elbows, transitions, and wall or roof caps must not exceed the equivalent of 140 feet.
-
Page 10: Step 3: Prepare The Venting
DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in electrical shock. ● Your microwave oven is shipped with the blower assembled for room venting. If you want wall-venting or roof-vented installation, you must change the blower, as detailed below. Before You Start 1. -
Page 11: Roof-Vented Installation
Blower plate. Discard knockouts. Be careful not to distort the plate. See Figure 20. 3. Carefully lift the blower unit out of the microwave oven. 4. Rotate blower unit 90° so the exhaust ports face the top of the cabinet. See Figure 21. - Page 12 STEP 4: PREPARE THE WALL & UPPER CABINET To avoid personal injury or property damage, do not attempt to install this microwave oven if you cannot find a wall stud. Measure And Track/Tape Up The Templates 1. Using a plumb line and measuring tape, find and mark the vertical center line on the back wall, as in Figure 24.
-
Page 13: Drill The Holes In The Wall And Upper Cabinet
Align filler blocks over the two openings in the top of the microwave oven cabinet and attach to cabinet with masking tape. See Figure 27. 3. Cut or drill a 2" diameter hole at the area marked M. Power supply cord hole on the upper cabinet template. -
Page 14: Step 5: Install The Mounting Plate
STEP 5: INSTALL THE MOUNTING PLATE The Oven Must Be Connected To At Least One Wall Stud. 1. Draw a vertical line on the wall at the center of the 30 wide space. Use the mounting plate as the template for the rear wall. - Page 15 For Wall-Vented Make the box cutout for the rear wall duct. – 1 piece mounting plate: Using a pencil, put dots through slots F and G, and through holes H and I. Remove the mounting plate and draw lines extending through the points. This will give the location and size of the box cutout for the rear wall duct.
-
Page 16: Step 6: Attach The Oven To The Wall
To avoid risk of personal injury or property damage, use will need two people to install this microwave oven. 1. Carefully lift microwave oven and hang it on support tabs (See Figure 28) at the bottom of the mounting plate.Reaching through upper cabinet, thread power supply cord through the power supply cord hole in the bottom of the upper cabinet. - Page 17 Insert the end of the filter screen without ring into the opening and slide towards the side of the microwave oven. Insert ring end of filter screen into the opening and slide entire screen towards the center of the microwave until screen is securely in position.
- Page 18 MEMO...
- Page 20 Printed in Korea...