Related Manuals for DeWalt HEAVY-DUTY SDS PLUS D25123-XE
Summary of Contents for DeWalt HEAVY-DUTY SDS PLUS D25123-XE
- Page 1 INSTRUCTION MANUAL D25123-XE, D25124-XE, D25213-XE, D25314-XE, D25315-XE HEAVY-DUTY SDS PLUS ROTARY HAMMERS ® D25330-XE HEAVY-DUTY SDS PLUS CHIPPING HAMMER ®...
-
Page 3: Definitions: Safety Guidelines
SAVE THESE INSTRUCTIONS Definitions: Safety Guidelines 1) WORK AREA SAFETY The definitions below describe the level of severity for each a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. signal word. Please read the manual and pay attention to these b) Do not operate power tools in explosive atmospheres, such as in the symbols. -
Page 4: Electrical Safety
d) Remove any adjusting key or wrench before turning the power tool on. A power tool, taking into account the working conditions and the work to be wrench or a key left attached to a rotating part of the power tool may result in performed. - Page 5 Additional Safety Instructions for Rotary Hammers • Do not strike jammed bits with a hammer to dislodge them. Fragments of metal or material chips could dislodge and cause injury. • Wear ear protectors. Exposure to noise can cause hearing loss. •...
-
Page 6: Markings On Tool
Motor WARNING: Always use eye protection. All users and bystanders must wear eye protection that conforms to ASNZS1337. Your D WALT tool is powered by a D WALT-built motor. Be sure your power supply agrees with the nameplate markings. Voltage decrease of more than 10% will cause WARNING: We recommend the use of a residual current device with a residual loss of power and overheating. -
Page 7: Lock-On Button
Switch FIG. 1 FIG. 2 To start the rotary hammer, depress the trigger switch D25213-XE D25123-XE, D25124-XE (D). To stop rotary hammer, release the switch. VARIABLE SPEED TRIGGER The variable speed trigger switch (D) permits speed control. The farther the trigger switch is depressed, the higher the speed of the drill. - Page 8 Reversing Lever (Fig. 1–4) FIG. 5 DRILL-ONLY MODE D25123-XE, D25124-XE, D25213-XE, D25314-XE, D25315-XE The reversing lever is used to reverse the rotary hammer for backing out screws or jammed bits. It is located above the trigger, shown in Figure 2. CAUTION: When reversing to clear jammed bits, be ready for strong reactive torque.
-
Page 9: Operation
FIG. 6 1. Always unplug the drill when attaching or changing bits or accessories. WARNING: Burn Hazard. ALWAYS wear gloves 2. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power when changing bits. Accessible metal parts on the tool auger bits, or hole saws. -
Page 10: Maintenance
MAINTENANCE DRILLING IN METAL D25123-XE, D25124-XE, D25213-XE, D25314-XE WARNING: Shock Hazard. To reduce the risk of serious personal injury, turn An SDS Plus ® to round shank adaptor chuck is required. Ensure that tool is in drill- tool off and disconnect from power source before making any adjustments or only mode. - Page 11 MAXIMUM RECOMMENDED CAPACITIES 30 DAY NO SATISFACTION GUARANTEE If you are dissatisfied with any D WALT power tool, laser or nailer, for any reason, D25123-XE, D25124-XE simply return it to the point of purchase with your sales receipt within 30 days for a D25213-XE, D25314-XE, D25315-XE replacement unit or a full refund.
- Page 12 WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 • 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (FEB11) Part No. N079442 D25123-XE, D25124-XE, D25213-XE, D25314-XE, D25315-XE, D25330-XE Copyright © 2007, 2009, 2011 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...