Function Button Setting - Sony LMD-2451W Operating Instructions Manual

Submenu Setting
SUB INPUT Sets the input signal of the sub display.
SELECT You can select from among
COMPOSITE, Y/C, RGB,
COMPONENT, OPTION A-1, OPTION
A-2, OPTION B-1, OPTION B-2,
VIDEO WAVE and OFF.
When you select VIDEO WAVE, the
waveform and audio level are displayed.
(Audio level is displayed only when you
connect the BKM-220D/243HS/244CC/
250TG.)
The indications of the waveform and
audio level signify as illustrated below,
although the percentage of the
waveform, audio level L/R CH, units
and values of the scale do not appear on
the display.
Waveform
109%
100%
75%
50%
25%
0%
-4%
Notes
• The multi display with COMPOSITE
and Y/C, RGB and COMPONENT,
OPTION A-1 and OPTION A-2, and
OPTION B-1 and OPTION B-2 is not
displayed.
• When SUB INPUT SELECT is set to
OFF, the sub display is not displayed
even if you set MULTI DISPLAY
ENABLE to ON.
POSITION Sets the position of the sub display. You
can select from among 1 to 3 for the 4:3
display and 1 to 4 for the 16:9 display.
4:3 display
• 1: Top
• 2: Center
• 3: Bottom
16:9 display
• 1: Bottom left
• 2: Bottom right
• 3: Top right
• 4: Top left
FRAME Sets the position of the main display
when MULTI DISPLAY is set to POP
and the sub display is put on the 4:3
display.
• RIGHT: The main display is put by
the right side of the sub display.
• LEFT: The main display is put by the
left side of the sub display.
Submenu
SUB PICTURE
SIZE (LMD-
2451W/2051W)

FUNCTION BUTTON SETTING

USER CONFIG – FUNCTION BUTTON SETTING
Audio level
(dB)
Submenu
0
F1 BUTTON to F4
BUTTON
-10
-20
-30
-60
L CH R CH
About the function assigned to the
function button
SCAN
Press the button to change the scan size of the picture
according to the setting of "STANDARD" or
"FULL+NATIVE" selected in SCAN (page 26).
ASPECT
Press the button to set the aspect ratio of the picture, 4:3
or 16:9.
Note
The panel of LMD-2451W and LMD-2051W is 16:10
and the panel of LMD-1751W is 15:9.
When the 16:9 signal is displayed, black bars appear in
the upper and lower positions of the display. This is not
a malfunction. (See "Scan mode image" on page 26.)
EXT SYNC (external sync)
Press the button to operate the unit on an external sync
signal through the EXT SYNC IN connector.
EXT SYNC works when the component/RGB signals
are input.
Setting
Sets the size of the sub picture. You can
select from among 1 to 3. When the
setting is high, the size becomes large.
F 1 B U T T O N : xxxx
F 2 B U T T O N : xxxx
F 3 B U T T O N : xxxx
F 4 B U T T O N : xxxx
Setting
Assigns the function to the function
buttons of the front panel and turns the
function on or off.
You can assign the function from among
SCAN, ASPECT, EXT SYNC, BLUE
ONLY, MONO, MARKER, H/V
DELAY, MULTI DISPLAY, CLOSED
CAPTION, APA and I/P MODE.
Factory setting
• F1 button: EXT SYNC
• F2 button: SCAN
• F3 button: ASPECT
• F4 button: H/V DELAY
Adjustment Using the Menus
29