Toshiba IK-WF51R User Manual

Hide thumbs Also See for IK-WF51R:

Quick start manual and important safeguards (25 pages)

Table Of Contents

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

Table of Contents

Quick Links

Download this manual

NETWORK CAMERA

IK-WF51R

Model:

User's Manual

For information on our latest products and peripheral devices, refer to the

following Website:

http://www.toshibasecurity.com

If the URL changes, refer to the Toshiba website (http://www.toshiba.com/).

Table of Contents

Summary of Contents for Toshiba IK-WF51R

Page 1: Network Camera
NETWORK CAMERA IK-WF51R Model: User's Manual For information on our latest products and peripheral devices, refer to the following Website: http://www.toshibasecurity.com If the URL changes, refer to the Toshiba website (http://www.toshiba.com/).
Page 2: Table Of Contents
Table of Contents Introduction � �� 4 ImportantSafeguards�� 6 ImportantSafeguards(Cont�)�� 8 NotesonUseandInstallation�� 9 PrecautionsforUse�� 10 PackageContents�� 11 PhysicalDescription�� 12 PhysicalDescription�� 14 Installation�� 17 Hardware Installation ............................17 Network Deployment ............................17 Software Installation ............................. 19 Ready to Use ................................ 20 AccessingtheNetworkCamera��...
Page 3 Local storage > SD card management ....................... 122 Local storage > Content management ....................... 123 Troubleshooting�� 125 Specifications�� 126 AppearanceDiagram�� 128 TechnologyLicenseNotice � �� 129 End-userLicenseAgreementonFreeSoftwareComponentsUsedintheTOSHIBANetworkCamera�� 130 Trademarks � �� 135...
Page 4: Introduction
Introduction FCC (USA)-INFORMATION NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 5 Thank you for purchasing the IK-WF51R Network Camera. Before using the camera, read this User's Manual carefully to ensure correct usage. After reading this User's Manual, save it for future reference. The design, specifications, software, and User's Manual contents are subject to change without prior notice.
Page 6: ImportantSafeguards
Important Safeguards 1. Read Instructions Read all the safety and operating instructions before operating the product. 2. Retain Instructions Retain the safety instructions and user's manual for future reference. 3. Warnings Comply with all warnings on the product and in the user's manual. 4.
Page 7 12. Lightning For additional protection on this camera during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power supply and cable system. This will prevent damage to the camera due to lightning and power- line surges.
Page 8: Important Safeguards (Cont.)
Important Safeguards (Cont.) CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage"...
Page 9: NotesOnUseAndInstallation
Notes on Use and Installation l Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off. l Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen.
Page 10: PrecautionsForUse
Accordingly, Toshiba disclaims any and all liability arising out of the use of the product in any critical applications.
Page 11: PackageContents
For information on our latest products and peripheral devices, refer to the following Website: n http://www.toshibasecurity.com If the URL changes, refer to the Toshiba website (http://www.toshiba.com). l Mounting Plate / l Gasket / Sillica Gel and tape / Torx driver...
Page 12: PhysicalDescription
Physical Description Cover Screws Dome Cover Clear Cover Built-in Microphone IR illuminator Cover...
Page 13 CAMERA MAIN UNIT l Inner View Lens Contacts (A) Header (J7) Contacts for IR units (B) NOTE Header (J6) Align (B) to (A) when attaching Ethernet 10/100 RJ45 Socket the dome cover Gasket for RJ45 LAN Cable NOTE White gasket is for transportation.
Page 14: PhysicalDescription
Physical Description General I/O Terminal Block This Network Camera provides a general I/O terminal block which is used to connect external input / output devices. NOTE ● 3.3V DC is outputted from the terminal when connected to a power supply. The diagrams below apply when "Digital Input"...
Page 15: Status Led
Status LED The LED indicates the status of the Network Camera. Item LED Status Description Steady Power on and system booting LED off Powered off Steady + blinking Green every 1 sec. (Green LED on for Network heartbeat 1 sec and off for another) Steady Green LED off...
Page 16 SD/SDHC/SDXC Card and Capacity This network camera is compliant with Micro SD/SDHC/SDXC 64GB and other preceding standard Micro SD cards for local storage. NOTE ● There is a limit to the number of rewrites that is possible with the SD memory card. Replacing the SD memory card when performing periodic maintenance of the camera is recommended.
Page 17: Installation
Installation Hardware Installation Please verify that your product package contains all the accessories listed in the Package Contents listed on page 11. Depending on the user’s application, an Ethernet cable may be needed. The Ethernet cable should meet the specs of UTP Category 5 or higher. Hardware Installation is shown in the Quick Start Guide(QSG).
Page 18 2. In this case, if the Local Area Network (LAN) IP address of your Network Camera is 192.168.0.3, please forward the following ports for the Network Camera on the router. ■ HTTP port: default is 80 ■ RTSP port: default is 554 ■...
Page 19: Software Installation
4. After searching, the main installer window will pop up. Click on the MAC and model name which matches the MAC of the camera. IK-WR12A 0002D1714270 S/N: A1510XXXX MAC: 0002D1XXXXXX NOTE ● This Software is proprietary client software for TOSHIBA Network Camera.
Page 20: Ready To Use
Ready to Use 1. Access the Network Camera on the LAN. 2. Retrieve live video through a web browser.
Page 21: AccessingTheNetworkCamera
Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players and 3GPP-compatible mobile devices. Using Web Browsers Use Installation Wizard to access the Network Cameras on the LAN. If your network environment is not a LAN, follow these steps to access the Network Camera: ®...
Page 22 ® ► If you see a dialog box indicating that your security settings prohibit running ActiveX Controls, please enable the ActiveX ® Controls for your browser. 1. Choose Tools > Internet Options > Security > Custom Level. ® 2. Look for Download signed ActiveX controls;...
Page 23: Using Rtsp Players
Using RTSP Players To view the H.264/MPEG-4 streaming media using RTSP players, you can use players that support RTSP streaming. 1. Launch the RTSP player. 2. Choose File > Open URL. A URL dialog box will pop up. 3. The address format is rtsp://<ip address>:<rtsp port>/<RTSP streaming access name for stream1, stream2 or stream3>...
Page 24: Using 3Gpp-Compatible Mobile Devices
Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet. For more information on how to set up the Network Camera over the Internet, please refer to Setup the Network Camera over the Internet on page To utilize this feature, please check the following settings on your Network Camera: 1.
Page 25: MainPage
Main Page This chapter explains the screen elements on the main page. It is composed of the following sections: TOSHIBA Logo, Host Name, Camera Control Area, Configuration Area, and Live Video Window. TOSHIBA logo Resize Buttons Host name Camera Control...
Page 26 IMPORTANT: The Local dewarp function is designed for use with 3rd-party software that did not implement the dewarp plug-ins. A video stream can be dewarped on the camera into a regional or panoramic view before being sent to the client side. However, since the video has already been dewarped into a more viewable rectilinear view, you can not exert PTZ control or change the view angle on the client computer.
Page 27 (Original) Display mode: 1O View (Original View) When mounted on a ceiling, the panoramic camera can cover an approximately 50 m² surveillance area (hung at a height of approximately 3 meters), while still keeping details in videos with recognizable facial features of people trafficking through the area.
Page 28 Viewers can use a mouse click and swipe to quickly scroll horizontally through the surveillance area. * Note that the dividing line falls approximately on the center of the TOSHIBA logo. 2P View (Panoramic View)
Page 29 1O3R (One Original & Three Regional) Display mode: The 1O3R mode provides access to multiple live view sections within the hemisphere and the reference to their relative positions on an Original circular view. The FOV indicators (#1 ~ #3) interact with your current operation as you may zoom in/out or move the live view window to a different place.
Page 30 (Four Regional) Display mode: The view control and look and feel are identical to that as described in the 1O3R mode except the absence of the Original circular view. 4R PRO (Four Regional Proactive) Display mode: The 4R PRO mode is similar to the 4R mode except that the quad view windows consecutively rotate in correspondence to the change of view area in one window.
Page 31 Video Stream: This Network Camera supports multiple streams (stream #1 ~ #3) simultaneously. You can select any one of them for live viewing. For more information about multiple streams, please refer to page 88 for detailed information. Manual Trigger: Click to manually enable or disable an event trigger. Please configure an event setting before enabling this function.
Page 32 Camera. It is suggested that a password is applied to the Network Camera so that only the administrator can configure the Network Camera. For more information, please refer to the description for the Configuration menus on page 37. Hide Button You can click the hide button to hide the control panel or display the control panel.
Page 33 Snapshot: Click this button to capture and save still images. The captured images will be displayed in a pop-up window. Right-click the image and choose Save Picture As to save it in JPEG (*.jpg) or BMP (*.bmp) format. Pause: Pause the transmission of the streaming media. The button becomes the Resume button after clicking the Pause button.
Page 34 ■ The following window is displayed when the video mode is set to MJPEG: Video Title Time Video (HTTP-V) 2011/03/10 17:08:56 Title and Time Video 17:08:56 2011/03/10 Video Control Buttons Video Title: The video title can be configured. For more information, please refer to Audio and Video > Image on page 76.
Page 35: Client Settings
Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer. When completed with the settings on this page, click Save on the page bottom to enable the settings. H.264 / MPEG-4 Media Options H.264/MPEG-4 Media Options Select to stream video or audio data or both.
Page 36: Mp4 Saving Options
MP4 Saving Options Users can record live video as they are watching it by clicking Start MP4 Recording on the main page. Here, you can specify the storage destination and file name. Folder: Specify a storage destination for the recorded video files. File name prefix: Enter the text that will be appended to the front of the video file name.
Page 37 Click Configuration on the main page to enter the camera setting pages. Note that only Administrators can access the configuration page. TOSHIBA offers an easy-to-use user interface that helps you set up your network camera with minimal effort. To simplify the setting procedure, two types of user interfaces are available: Advanced Mode for professional users and Basic Mode for entry-level users.
Page 38: System > General Settings
Advanced Mode Navigation Area Panoramic camera Configuration List Click to switch to Basic Mode Firmware Version Each function on the configuration list will be explained in the following sections. Those functions that are displayed only in Advanced Mode are marked with Advanced Mode . If you want to set up advanced functions, please click on [Advanced Mode] at the bottom of the configuration list.
Page 39 System time Keep current date and time: Select this option to preserve the current date and time of the Network Camera. The Network Camera’s internal real-time clock maintains the date and time even when the power of the system is turned off. Synchronize with computer time: Select this option to synchronize the date and time of the Network Camera with the local computer.
Page 40: System > Homepage Layout
System > Homepage layout Advanced Mode This section explains how to set up your own customized homepage layout. General settings This column shows the settings of your hompage layout. You can manually select the background and font colors in Theme Options (the second tab on this page). The settings will be displayed automatically in this Preview field.
Page 41 Theme Options Here you can change the color of your homepage layout. There are three types of preset patterns for you to choose from. The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings. Font Color of the Video Title Font Color...
Page 42 ■ Follow the steps below to set up a custom homepage: 1. Click Custom on the left column. 2. Click to select a color on on the right column. Color Selector Custom Pattern 3. The palette window will pop up as shown below. 4.
Page 43: System > Logs
System > Logs Advanced Mode This section explains how to configure the Network Camera to backup the system log to a remote server. Log server settings Follow the steps below to set up the remote log: 1. Select Enable remote log. 2.
Page 44: System > Parameters
Access log Access log displays the access time and IP address of all viewers (including operators and administrators) in chronological order. The access log is stored in the Network Camera’s buffer and older events will be overwritten when the number of events reaches a limit. The access log messages stored in the Network Camera will be all cleared after reboot or power down the Network Camera.
Page 45: System > Maintenance
Note: Do not power off the Network Camera during the upgrade! Follow the steps below to upgrade the firmware: 1. Download the latest firmware file from the TOSHIBA website. The file is in .pkg file format. 2. Click Browse… and specify the firmware file.
Page 46 General settings > Restore This feature allows you to restore the Network Camera to factory default settings. Network: Select this option to retain the Network Type settings (please refer to Network Type on page 60). Daylight Saving Time: Select this option to retain the Daylight Saving Time settings (please refer to Import/Export files below on this page).
Page 47 3. Open the file with text editor and locate your time zone; set the start and end time of DST. When completed, save the file. In the example below, DST begins each year at 2:00 a.m. on the second Sunday in March and ends at 2:00 a.m.
Page 48 The following message is displayed when attempting to upload an incorrect file format. Export configuration file: Click to export all parameters for the device and user-defined scripts. Update configuration file: Click Browse… to update a configuration file. Please note that the model and firmware version of the device should be the same as the configuration file.
Page 49: Security > User Account
Security > User Account This section explains how to enable password protection and create multiple accounts. Root Password The administrator account name is “root”, which is permanent and can not be deleted. If you want to add more accounts in the Manage User column, please apply the password for the “root” account first. 1.
Page 50: Security > Https (Hypertext Transfer Protocol Over Ssl)
Security > HTTPS (Hypertext Transfer Protocol over SSL) Advanced Mode This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer). It helps protect streaming data transmission over the Internet on higher security level. Create and Install Certificate Method Before using HTTPS for communication with the Network Camera, a Certificate must be created first.
Page 51 5. Click Home to return to the main page. Change the address from “http://” to “https://“ in the address bar and press Enter on your keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to enable HTTPS. https:// https://192.168.5.151/index.html...
Page 52 Create certificate request and install : Select this option if you want to create a certificate from a certificate authority. 1. Select this option from a method pull-down menu. 2. Click Create certificate to generate the certificate.
Page 53 3. If you see the following Information bar, click OK and click on the Information bar at the top of the page to allow pop-ups. 4. The pop-up window shows an example of a certificate request. 5. Look for a trusted certificate authority that issues digital certificates. Enroll the Network Camera. Wait for the certificate authority to issue a SSL certificate;...
Page 54 NOTE ● 1. How do I cancel the HTTPS settings? 1-1. Click on the Remove certificate button. 1-2. The webpage will redirect to a non-HTTPS page automatically. ● 2. If you want to create and install other certificates, please remove the existing one. Enable HTTPS Check this item to enable HTTPS communication, then select a connection option: ”HTTP &...
Page 55: Security > Access List
Security > Access List This section explains how to control access permission by verifying the client PC’s IP address. General Settings Maximum number of concurrent streaming: Simultaneous live viewing for 1~10 clients (including stream 1 to stream 3). The default value is 10. If you modify the value and click Save, all current connections will be disconnected and automatically attempt to re-link.
Page 56 ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access. Please note that those checked connections will only be disconnected temporarily and will automatically try to re-link again (IE Explore or Quick Time Player).
Page 57 There are three types of rules: Single: This rule allows the user to add an IP address to the Allowed/Denied list. For example: 192.168.2.1 Network: This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List.
Page 58 Security > IEEE 802.1x Advanced Mode Enable this function if your network environment uses IEEE 802.1x, which is a port-based network access control. The network devices, intermediary switch/access point/hub, and RADIUS server must support and enable 802.1x settings. The 802.1x standard is designed to enhance the security of local area networks, which provides authentication to network devices (clients) attached to a network port (wired or wireless).
Page 59 3. When all settings are complete, move the Network Camera to the protected LAN by connecting it to an 802.1x enabled switch. The devices will then start the authentication automatically. NOTE ● The maximum length of password is 200 symbols. ●...
Page 60: Network > General Settings
Network > General settings This section explains how to configure a wired network connection for the Network Camera. Network Type Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers. The default setting for the Network Type is LAN. Rememer to click Save when you complete the Network setting.
Page 61 Primary DNS: The primary domain name server that translates hostnames into IP addresses. Secondary DNS: Secondary domain name server that backups the Primary DNS. Primary WINS server: The primary WINS server that maintains the database of computer name and IP address.
Page 62 NOTE ● If the default ports are already used by other devices connected to the same router, the Network Camera will select other ports for the Network Camera. ● If UPnP is not supported by your router, you will see the following message: Error: Router does not support UPnP port forwarding.
Page 63 4. In the Networking Services dialog box, select Universal Plug and Play and click OK. 5. Click Next in the following window. 6. Click Finish. UPnP is enabled. ● How does UPnP work? UPnP networking technology provides automatic IP configuration and dynamic discovery of devices added to a network.
Page 64 Enable IPv6 Select this option and click Save to enable IPv6 settings. Please note that this only works if your network environment and hardware equipment support IPv6. The ® browser should be Microsoft Internet Explorer 6.5 or above. When IPv6 is enabled, by default, the network camera will listen to router advertisements and be assigned with a link-local IPv6 address accordingly.
Page 65 Please follow the steps below to link to an IPv6 address: 1. Open your web browser. 2. Enter the link-global or link-local IPv6 address in the address bar of your web browser. 3. The format should be: http://[2001:0c08:2500:0002:0202:d1ff:fe04:65f4]/ IPv6 address 4.
Page 66 Port HTTPS port: By default, the HTTPS port is set to 443. It can also be assigned to another port number between 1025 and 65535. Two way audio port: By default, the two way audio port is set to 5060. Also, it can also be assigned to another port number between 1025 and 65535.
Page 67 FTP port: The FTP server allows the user to save recorded video clips. You can use TOSHIBA Installation Wizard software to upgrade the firmware via FTP server. By default, the FTP port is set to 21. It also can...
Page 68: Network > Streaming Protocols
Network > Streaming protocols Advanced Mode HTTP streaming To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security > User account on page 49 for details. Authentication: Depending on your network security requirements, the Network Camera provides two types of security settings for an HTTP transaction: basic and digest.
Page 69 RTSP Streaming To utilize RTSP streaming authentication, make sure that you have set a password for the Network Camera first; please refer to Security > User account on page 49 for details.
Page 70 Authentication: Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic, and digest. basic authentication is selected, the password is sent in plain text format, but there can be potential risks of it being intercepted.
Page 71 Multicast settings for stream 1 ~ 3: Click the items to display the detailed configuration information. Select the Always multicast option to enable multicast for stream 1 ~ 3. Unicast video transmission delivers a stream through point-to-point transmission; multicast, on the other hand, sends a stream to the multicast group address and allows multiple clients to acquire the stream at the same time by requesting a copy from the multicast group address.
Page 72 DDNS. ChangeIP.com http://www.changeip.com/toshiba/ No-IP.com http://www.no-ip.com/ext/toshiba.php Host Name: If the User wants to use a DDNS service, enter the camera name that is registered at the DDNS server.
Page 73 Network > QoS (Quality of Service) Advanced Mode Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality to different services on the network. Quality of service guarantees are important if the network capacity is insufficient, especially for real-time streaming multimedia applications. Quality can be defined as, for instance, a maintained level of bit rate, low latency, no packet dropping, etc.
Page 74 QoS/DSCP (the DiffServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer). The Differentiated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a field to the IP header, called the DSCP (Differentiated Services Codepoint). This is a 6-bit field that provides 64 different class IDs.
Page 75: Network > Snmp (Simple Network Management Protocol)
Network > SNMP (Simple Network Management Protocol) Advanced Mode This section explains how to use the SNMP on the network camera. The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices. It helps network administrators to remotely manage network devices and find, solve network problems with ease.
Page 76: Audio And Video > Image
Audio and Video > Image Advanced Mode This section explains how to configure the image settings of the Network Camera. It is composed of the following four columns: General settings, Preference, Exposure, Zoom and Focus, and Privacy mask. General settings Video title: Enter a name that will be displayed on the title bar of the live video as the picture shown below.
Page 77 Video orientation: Flip - vertically reflect the display of the live video; Mirror - horizontally reflect the display of the live video. Select both options if the Network Camera is installed upside-down (e.g., on the ceiling) to correct the image orientation. Please note that if you have preset locations, those locations will be cleared after flip/mirror setting.
Page 78 Day/Night Switch to B/W in night mode Select this checkbox to enable the Network Camera to automatically switch to Black & White display during the night mode. Turn on external IR illuminator in night mode Select this to turn on an external IR illuminator (connected via Digital Output lines) when the camera detects low light condition and enters the night mode.
Page 79 Preference On this page, you can tune the White balance, Image adjustment, WDR enhancement and 3D Noise reduction parameters. You can configure two sets of preferred settings: one for normal situations, the other for special situations, such as day/night/schedule mode. Sensor Setting 1: For normal situations Sensor Setting 2:...
Page 80 ■ Enable low light compensation: Select this option in low light mode, and the values of sharpness and brightness will change automatically as the noise reduction function. NOTE: Sharpness may be temporarily emphasized as it becomes dark. WDR enhancement This function allows users to identify more image details with an extreme contrast from an object of interest with one shadowed side against a bright background, e.g., an entrance.
Page 81 If you want to configure another sensor setting for day/night/schedule mode, please click Profile to open the Profile Settings page as shown below. Please follow the steps below to setup a profile: 1. Check Enable and apply this profile. 2. Select the applied mode: Day mode, Night mode, or Schedule mode. Please manually enter a range of time if you choose Schedule mode.
Page 82 Exposure Advanced Mode On this page, you can set the Exposure measurement window, Exposure level, and Exposure control, You can configure two sets of Exposure settings: one for normal situations, the other for special situations, such as day/night/schedule mode. Sensor Setting 1: For normal situations Sensor Setting 2: For special situations...
Page 83 The inclusive window refers to “weighted window“; the exclusive window refers to “ignored window“. It adopts the weighted averages method to calculate the value. Include Weighted region Ignored region Exclude ■ BLC (Back Light Compensation): This option will automatically add a “weighted region“ in the middle of the window and give the necessary light compensation.
Page 84 If you want to configure another sensor setting for day/night/schedule mode, please click Profile to open the Profile settings page as shown below. Please follow the steps below to setup a profile: 1. Check Enable and apply this profile. 2. Select the applied mode: Day mode, Night mode, or Schedule mode. Please manually enter a range of time through which you want the Schedule mode to apply.
Page 85 Privacy mask Advanced Mode Click Privacy Mask to open the settings page. On this page, you can block out certain sensitive zones to address privacy concerns. ■ To set the privacy mask windows, follow the steps below: 1. Click New to add a new window. A text box will appear allowing you to enter a name for the mask. 2.
Page 86 Pixel Calculator Click the Start button at the lower screen to create a pixel calculator window. Place your cursor on the window to move it to an area of your interest, and change the size of window to fit the area of interest. Once they are drawn, the numbers of pixels on the sides of windows will appear.
Page 87: Audio And Video > Stream
Audio and Video > Stream FOV (Field of View) The Field of View window allows you to select either the Hemispheric View or a 1080P Full HD mode. The 1080P Full HD mode provides a dewarpped section (1920x1080 pixels) out of the 175 degrees hemispheric view.
Page 88 Advanced Mode Stream settings Local dewarp mode: You can set up different local dewarp mode from drop down list in stream 1 and stream 2. If you disable this function, select 1O from the list. This Network Camera supports multiple streams with frame size ranging from 192 x 192 to 1920 x 1920 pixels.
Page 89 Click the stream item to display the detailed information. This Network Camera offers real-time H.264, MPEG-4 and MJPEG compression standards (Triple Codec) for real-time viewing. H.264 MPEG-4 mode is selected, the video is streamed via RTSP protocol. There are several parameters for you to adjust the video performance: ■...
Page 90 ■ Intra frame period Determine how often to plant an I frame. The shorter the duration, the more likely you will get better video quality, but at the cost of higher network bandwidth consumption. Select the intra frame period from the following durations: 1/4 second, 1/2 second, 1 second, 2 seconds, 3 seconds, and 4 seconds. ■...
Page 91 JPEG mode is selected, the Network Camera continuously sends JPEG images to the client, producing a moving effect similar to a filmstrip. Every single JPEG image transmitted guarantees the same image quality, which in turn comes at the expense of variable bandwidth usage. Because the media contents are a combination of JPEG images, no audio data is transmitted to the client.
Page 92: Audio And Video > Audio
Audio and Video > Audio Audio Settings Mute: Select this option to disable audio transmission from the Network Camera to all clients. Note that if muted, no audio data will be transmitted even if audio transmission is enabled on the Client Settings page.
Page 93: Ptz > Ptz Settings
PTZ > PTZ settings This window is functional only when you configure a video stream to be using the Local dewarp function. Changing the Field of View In this window, functional items related to the preset positions have been cancelled. This window is now used for changing the field of view when the Local dewarp is applied to a video stream.
Page 94 2. Adjust the shooting area to the desired position using the PTZ keypad on the live screen. Note that the pan, tilt, zoom speeds only applies in this window. They do not apply to the live view in Main Page...
Page 95: Event > Event Settings
Event > Event settings Advanced Mode This section explains how to configure the Network Camera to respond to particular situations (event). A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notifications. Click on Help, there is an illustration shown in the pop-up window explaining that an event can be triggered by many sources, such as motion detection or external digital input devices.
Page 96 ■ Event name: Enter a name for the event setting. ■ Enable this event: Select this option to enable the event setting. ■ Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority setting will be executed first. ■...
Page 97 ■ Audio detection A preset threshold can be configured with an external microphone as the trigger to system event. The triggering condition can be an input exceeding or falling below a threshold. Audio detection can take place as a complement to motion detection or as a method to detect activities not covered by the camera's view.
Page 98 ■ Extension platform (EP) It is presumed that you already uploaded and enabled the EP modules before you can associatee EP triggers with an Event setting. Click on the Set EP Trigger button to open the EP setup menu. The triggering conditions available with 3rd-party software modules known as EP will be listed.
Page 99 3. Action Define the actions to be performed by the Network Camera when a trigger is activated. ■ Trigger digital output for seconds Select this option to turn on the external digital output device when a trigger is activated. Specify the length of the trigger interval in the text box.
Page 100: Add Server
Add server To configure an event with video recording or snapshots, it is necessary to configure/provide servers and storage media settings so that the Network Camera will know where to send the media files to when a trigger is activated. Click Add server to unfold the server setting window.
Page 101 To verify if the email settings are correctly configured, click Test. The result will be shown in a pop-up window. If successful, you will also receive an email indicating the result. Click Save server to enable the settings, then click Close to exit the Add server page. After you set up the first event server, a new item for event server will automatically appear on the Server list.
Page 102 ■ Passive mode Most firewalls do not accept new connections initiated from external requests. If the FTP server supports passive mode, select this option to enable passive mode FTP and allow data transmission to pass through the firewall. To verify if the FTP settings are correctly configured, click Test. The result will be shown in a pop-up window as shown below.
Page 103 Network storage: Select to send the media files to a network storage location when a trigger is activated. Please refer to NAS server on page 119 for details. Click Save server to enable the settings, then click Close to exit the Add server page. ■...
Page 104 The format is: HH (24r) Click to open the file list for that hour 2014/08/20 2014/08/20 Click to go back to the previous Click to delete level of the directory selected items Click to delete all recorded data 2014/08/20 2014/08/20 The format is: File name prefix + Minute (mm) You can set up the file name prefix on Add media page.
Page 105: Add Media
Add media Add media Click to open the media setting window. You can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. There are three choices of media types available: Snapshot, Video Clip, and System log.
Page 106 ■ Add date and time suffix to the file name Select this option to add a date/time suffix to the file name. For example: Snapshot_20141015_100341 File name preﬁx Date and time sufﬁx The format is: YYYYMMDD_HHMMSS Click Save media to enable the settings, then click Close to exit the Add media page. After you set up the first media server, a new column for media server will automatically display on the Media list.
Page 107 ■ Maximum duration Specify the maximum recording duration in seconds. Up to 10 seconds of video can be recorded. For example, if pre-event recording is set to 5 seconds and the maximum duration is set to 10 seconds, the Network Camera continues to record for another 4 seconds after a trigger is activated. 1 sec.
Page 108 In the Event settings column, the Servers and Medias you configured will be listed; please make sure the Event -> Status is indicated as ON, in order to enable the event triggering action. When completed, click Save event to enable the settings and click Close to exit Event Settings page. The new Event / Server settings / Media will appear in the event drop-down list on the Event setting page.
Page 109: Applications > Motion Detection
Applications > Motion detection This section explains how to configure the Network Camera to enable motion detection. A total of three motion detection windows can be configured. Motion Detection Setting 1: For normal situations Motion Detection Setting 2: Follow the steps below to enable motion detection: For special situations 1.
Page 110 A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the defined threshold. Percentage = 30% If you want to configure specific motion detection settings individually for day/night/schedule operations, please click Profile to open the Motion Detection Profile Settings page as shown below.
Page 111 NOTE ● How does motion detection work? There are two motion detection parameters: Sensitivity and Percentage. In the illustration above, frame A and frame B are two sequential images. Pixel differences between the two frames are detected and highlighted in gray (frame C) and will be compared with the sensitivity setting.
Page 112: Applications > Di And Do
Applications > DI and DO Connect DI or DO devices to the camera's terminal block, the camera will automatically detect the current connection state as pulled-high or pulled-low. You may then define the triggering condition. Digital input: Select High or Low to define the "Normal status" for the digital input. The Network Camera will report the current status.
Page 113: Applications > Audio Detection
Applications > Audio detection Audio detection, along with video motion detection, is applicable in the following scenarios: 1. Detection of activities not covered by camera view, e.g., a loud input by gun shots or breaking a door/window. 2. A usually noisy environment, such as a factory, suddenly becomes quiet due to a breakdown of machines.
Page 114 You can use the Profile window to configure a different Audio detection setting. For example, a place can be noisy in the day time and become very quiet in the night. 1. Click on the Enable this profile checkbox. Once the Audio detection window is opened, the current sound input will be interactively indicated by a fluctuating yellow wave diagram.
Page 115: Applications > Extension Platform
Applications > Extension Platform Users can store and execute 3rd-party software modules onto the camera's flash memory or SD card. • Once the software package is successfully uploaded, the module configuration information is displayed. When uploading a module, the camera will examine whether the module fits the predefined Extension platform requirements.
Page 116 To start a module, select the checkcircle in front, and click the Start button. If you should need to remove a module, select the checkcircle in front and then click the Stop button. By then the module status will become OFF, and the X button will appear at the end of the row.
Page 117: Recording > Recording Settings
Recording > Recording settings Advanced Mode This section explains how to configure the recording settings for the Network Camera. Recording Settings Insert your SD card and click here to test NOTE ● Please remember to format your SD card when used for the first time. Please refer to page 122 for detailed information.
Page 118 If you enable adaptive recording and enable time-shift cache stream on Camera A, only when an event is triggered on Camera A will the server record the streaming data in full frame rate; otherwise, it will only request the I frame data during normal monitoring, thus effectively save lots of bandwidths and storage. NOTE ●...
Page 119 2. Destination You can select the SD card or network storage (NAS) for the recorded video files. If you have configured a NAS server, see details in the following. NAS server Click Add NAS server to open the server setting window and follow the steps below to set up: 1.
Page 120 If successful, you will receive a test.txt file on the network storage server. 3. Enter a server name. 4. Click Save to complete the settings and click Close to exit the page. ■ Capacity: You can choose either the entire free space available or limit the reserved space. The recording size limit must be larger than the reserved amount for cyclic recording.
Page 121 Event If you want to enable recording notification, please click to configure event triggering settings. Please refer to Event > Event settings on page 95 for more details. When completed, select Enable this recording. Click Save to enable the setting and click Close to exit this page.
Page 122: Local Storage > Sd Card Management
Local storage > SD card management Advanced Mode This section explains how to manage the local storage on the Network Camera. Here you can view SD card status, and implement SD card control. SD card status This column shows the status and reserved space of your SD card. SD card format Remember to format the SD card when using for the first time.
Page 123: Local Storage > Content Management
Local storage > Content management Advanced Mode This section explains how to manage the content of recorded videos on the Network Camera. Here you can search and view the records and view the searched results. Searching and Viewing the Records This column allows the user to set up search criteria for recorded data.
Page 124 ■ Play: Click on a search result which will highlight the selected item in blue. Click the Playback window will open automatically to play back the selected file. For example: Time line of video clip, and Full screen, Pause, Playback, reload function.
Page 125: Troubleshooting
Troubleshooting Reset and restore If an operational problem occurred in the camera, please refer to the Reset and Restore function on page 15. Restoring the factory defaults will erase any previous settings. Audio When using multiple network cameras, restart Internet Explorer each time you switch the camera.
Page 126: Specifications
Specifications Power supply 12V DC ± 10 %, PoE(IEEE802.3af), PoE+(IEEE802.3at) Consumption current 12V DC / 2.1 A, Image pickup device 1/2.5 inch (4:3), 5Mp CMOS Digital Image Sensor Maximum resolution Horizontal 1920, Vertical 1920 pixels Scanning system Progressive Lens Aperture F=1:2.8 Focal length f= 1.5mm Angle of view(Typical value) Horizontal 175°...
Page 127 ●Designsandspecificationsmaychangewithoutpriornoticeforbetterimprovement� ●Screens,photos,illustrationsandotherdiagramscontainedinthisuser'smanualmayslightly changefromactualones� *1: Varies in accordance with the object, image quality, network environment and performance of the personal computer used. *2: The sound may not be clear depending on the conditions of the lines. *3: An internal heater is automatically turned on at low temperature, when a power supply is PoE+ and 12V DC.
Page 128: AppearanceDiagram
Appearance Diagram M3X0.5 TH 0.43"(11) (Mounting Plate) Dimensions: inch (mm)
Page 129: TechnologyLicenseNotice
The software is protected by the Copyright Law, Universal Copyright Convention, and other intellectual property laws and agreements. The permission of Toshiba and the third party must therefore be obtained before the software can be reproduced. Contact Toshiba if you need it for more information at...
Page 130: End-UserLicenseAgreementOnFreeSoftwareComponentsUsedInTheToshibaNetworkCamera
End-user License Agreement on Free Software Components Used in the TOSHIBA Network Camera GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Page 131 having been made by running the Program). Whether that is true depends on what the Program does. 1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty;...
Page 132 c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it.
Page 133 a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded.
Page 134 END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
Page 135: Trademarks
Trademarks ● Microsoft, Windows and Interner Explorer are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries. ● Intel and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiares in the United States and other countries. ●...
Page 136 TOSHIBA AMERICA INFORMATION SYSTEMS, INC. Surveillance & IP Video Products 9740 Irvine Boulevard, Irvine, CA 92618-1697 Phone Number: (877) 855-1349...

This manual is also suitable for:

Ik-wf51a

Toshiba IK-WF51R User Manual

Quick Links

NETWORK CAMERA

Related Manuals for Toshiba IK-WF51R

Summary of Contents for Toshiba IK-WF51R

This manual is also suitable for:

Table of Contents