Table of Contents
Advertisement
3 . 3 .
3 .
3 . 3 .
Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0,
RAID 1, RAID 10, and software RAID 5 configuration using the Intel
Matrix Storage Manager, or RAID 0, RAID 1, and RAID 10 configuration
using the LSI Logic Embedded SATA RAID utility in the Intel
Southbridge.
These connectors are set to I D E
Serial ATA boot/data hard disk drives to these connectors. If you intend to
create a Serial ATA RAID set using these connectors, set the Configure SATA
A s
A s item in the BIOS to [RAID]. See section 5.3.4 for details.
A s
A s
A s
P5MT-R
P5MT-R SATA connectors
I m p o r t a n t n o t e o n S e r i a l A T A
I m p o r t a n t n o t e o n S e r i a l A T A
I m p o r t a n t n o t e o n S e r i a l A T A
I m p o r t a n t n o t e o n S e r i a l A T A
I m p o r t a n t n o t e o n S e r i a l A T A
When using the connectors in I D E
disk drive to the SATA1 or SATA2 connector. Refer to the table below for
the recommended SATA hard disk drive connections.
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
S A T A 1 / S A T A 3
S A T A 1 / S A T A 3
S A T A 1 / S A T A 3
S A T A 1 / S A T A 3
S A T A 1 / S A T A 3
S A T A 2 / S A T A 4
S A T A 2 / S A T A 4
S A T A 2 / S A T A 4
S A T A 2 / S A T A 4
S A T A 2 / S A T A 4
4 - 1 0
4 - 1 0
4 - 1 0
4 - 1 0
4 - 1 0
®
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
M a s t e r
M a s t e r
M a s t e r
M a s t e r
M a s t e r
S l a v e
S l a v e
S l a v e
S l a v e
S l a v e
I D E mode by default. In I D E
I D E
I D E
I D E
SATA1
SATA2
(port0)
(port1)
I D E mode, connect the primary (boot) hard
I D E
I D E
I D E
C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n
®
ICH7R
I D E mode, you can connect
I D E
I D E
I D E
Configure SATA
Configure SATA
Configure SATA
Configure SATA
SATA3
SATA4
(port2)
(port3)
®
Advertisement
Table of Contents
