Yamaha YZF-R6(V) 2006 Service Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Motorcycle
  5. 2006 YZFR6V
  6. Service manual

Yamaha YZF-R6(V) 2006 Service Manual

Hide thumbs Also See for YZF-R6(V) 2006:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
2006
YZF-R6(V)
SERVICE MANUAL
2C0-28197-E0

Advertisement

Table of Contents
loading

Related Manuals for Yamaha YZF-R6(V) 2006

Summary of Contents for Yamaha YZF-R6(V) 2006

  • Page 1 2006 YZF-R6(V) SERVICE MANUAL 2C0-28197-E0...
  • Page 2 EAS20040 YZF-R6(V) 2006 SERVICE MANUAL ©2005 by Yamaha Motor Co., Ltd. First edition, November 2005 All rights reserved. Any reproduction or unauthorized use without the written permission of Yamaha Motor Co., Ltd. is expressly prohibited.
  • Page 3 EAS20070 NOTICE This manual was produced by the Yamaha Motor Company, Ltd. primarily for use by Yamaha dealers and their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one man- ual. Therefore, anyone who uses this book to perform maintenance and repairs on Yamaha vehicles should have a basic understanding of mechanics and the techniques to repair these types of vehicles.

  • Page 4: How To Use This Manual

    EAS20090 HOW TO USE THIS MANUAL This manual is intended as a handy, easy-to-read reference book for the mechanic. Comprehensive explanations of all installation, removal, disassembly, assembly, repair and check procedures are laid out with the individual steps in sequential order. •...

  • Page 5: Symbols

    EAS20100 1. Serviceable with engine mounted SYMBOLS 2. Filling fluid The following symbols are used in this manual 3. Lubricant for easier understanding. 4. Special tool NOTE: 5. Tightening torque The following symbols are not relevant to every 6. Wear limit, clearance vehicle.

  • Page 7: Table Of Contents

    EAS20110 TABLE OF CONTENTS GENERAL INFORMATION SPECIFICATIONS PERIODIC CHECKS AND ADJUSTMENTS CHASSIS ENGINE COOLING SYSTEM FUEL SYSTEM ELECTRICAL SYSTEM TROUBLESHOOTING...

  • Page 9: General Information

    VEHICLE IDENTIFICATION NUMBER ............. 1-1 MODEL LABEL..................1-1 FEATURES...................... 1-2 OUTLINE OF THE FI SYSTEM..............1-2 FI SYSTEM....................1-3 YCC-T (Yamaha Chip Controlled Throttle)..........1-4 INSTRUMENT FUNCTIONS ..............1-7 IMPORTANT INFORMATION ............... 1-12 PREPARATION FOR REMOVAL AND DISASSEMBLY......1-12 REPLACEMENT PARTS................. 1-12 GASKETS, OIL SEALS AND O-RINGS ..........

  • Page 10: Identification

    IDENTIFICATION EAS20130 IDENTIFICATION EAS20140 VEHICLE IDENTIFICATION NUMBER The vehicle identification number “1” is stamped on the right side of the steering head pipe. EAS20150 MODEL LABEL The model label “1” is affixed to the frame under the passenger seat. This information will be needed to order spare parts.

  • Page 11: Features

    FEATURES EAS20170 FEATURES ET2C01025 OUTLINE OF THE FI SYSTEM The main function of a fuel supply system is to provide fuel to the combustion chamber at the optimum air-fuel ratio in accordance with the engine operating conditions and the atmospheric temperature. In the conventional carburetor system, the air-fuel ratio of the mixture that is supplied to the combustion chamber is created by the volume of the intake air and the fuel that is metered by the jet used in the respective carburetor.

  • Page 12: Fi System

    FEATURES ET2C01019 FI SYSTEM The fuel pump delivers fuel to the fuel injector via the fuel filter. The pressure regulator maintains the fuel pressure that is applied to the fuel injector at only 324 kPa (3.24 kg/cm², 46.1 psi). Accordingly, when the energizing signal from the ECU energizes the fuel injector, the fuel passage opens, causing the fuel to be injected into the intake manifold only during the time the passage remains open.

  • Page 13: Ycc-T (Yamaha Chip Controlled Throttle)

    Yamaha developed the YCC-T system employing the most advanced electronic control technologies. Electronic control throttle systems have been used on automobiles, but Yamaha has developed a fast- er, more compact system specifically for the needs of a sports motorcycle. The Yamaha-developed system has a high-speed calculating capacity that produces computations of running conditions every 1/1000th of a second.
  • Page 14 FEATURES YCC-T system outline 1. Throttle position sensor (for throttle cable 18. Atmospheric pressure sensor pulley) 2. Throttle servo motor 3. Throttle position sensor (for throttle valves) 4. ECU (engine control unit) 5. ETV main CPU (32 bit) 6. ETV sub CPU (16 bit) 7.
  • Page 15 FEATURES YCC-T control outline 1. Throttle position sensor (for throttle cable 18. Idle speed control pulley) 19. Calculated throttle valve opening angle 2. Throttle position sensor (for throttle valves) 3. Crankshaft position sensor 4. Speed sensor 5. Coolant temperature sensor 6.

  • Page 16: Instrument Functions

    FEATURES • For the U.K. only: To switch the speedometer ET2C01020 INSTRUMENT FUNCTIONS and odometer/tripmeter displays between kilo- meters and miles, press the “SELECT” button Multi-function meter unit for at least one second. EW2C01003 WARNING Be sure to stop the vehicle before making Tachometer any setting changes to the multi-function meter unit.
  • Page 17 FEATURES To set the clock: “SELECT” button, and then push it again for a 1. Push the “SELECT” button and “RESET” but- few seconds until the stopwatch digits stop ton together for at least two seconds. flashing. 2. When the hour digits start flashing, push the “RESET”...
  • Page 18 FEATURES If any of the immobilizer system circuits are de- EC2C01021 CAUTION: fective, the immobilizer system indicator light will Do not operate the engine if it is overheated. flash, and then the odometer/trip meter/fuel re- serve trip meter/stopwatch display will indicate a two-digit error code (e.g., 51, 52, 53).
  • Page 19 FEATURES • Display brightness: • The indicator light is deactivated; in other This function allows you to adjust the bright- words, it will not come on or flash. (This set- ness of the displays and tachometer to suit the ting is selected when the indicator light flash- outside lighting conditions.
  • Page 20 FEATURES To adjust the shift timing indicator light bright- ness: 1. Push the “RESET” button to select the de- sired indicator light brightness level. 2. Push the “SELECT” button to confirm the se- lected indicator light brightness level. The dis- play will return to the odometer or tripmeter mode.

  • Page 21: Important Information

    5. Keep all parts away from any source of fire. EAS20200 REPLACEMENT PARTS Use only genuine Yamaha parts for all replace- ments. Use oil and grease recommended by Yamaha for all lubrication jobs. Other brands may be similar in function and appearance, but inferior in quality.

  • Page 22: Bearings And Oil Seals

    IMPORTANT INFORMATION EAS20230 BEARINGS AND OIL SEALS Install bearings “1” and oil seals “2” so that the manufacturer’s marks or numbers are visible. When installing oil seals, lubricate the oil seal lips with a light coat of lithium-soap-based grease. Oil bearings liberally when installing, if appropriate.

  • Page 23: Checking The Connections

    CHECKING THE CONNECTIONS EAS20250 CHECKING THE CONNECTIONS Pocket tester 90890-03112 Check the leads, couplers, and connectors for Analog pocket tester stains, rust, moisture, etc. YU-03112-C 1. Disconnect: • Lead NOTE: • Coupler • If there is no continuity, clean the terminals. •...

  • Page 24: Special Tools

    SPECIAL TOOLS EAS20260 SPECIAL TOOLS The following special tools are necessary for complete and accurate tune-up and assembly. Use only the appropriate special tools as this will help prevent damage caused by the use of inappropriate tools or improvised techniques. Special tools, part numbers or both may differ depending on the country. When placing an order, refer to the list provided below to avoid any mistakes.
  • Page 25 SPECIAL TOOLS Reference Tool name/Tool No. Illustration pages Oil filter wrench 3-12 90890-01426 YU-38411 Oil pressure gauge set 3-13 90890-03120 Oil pressure adapter H 3-13 90890-03139 Steering nut wrench 3-27, 4-57 90890-01403 Spanner wrench YU-33975 Fork spring compressor 4-47, 4-52 90890-01441 YM-01441 Rod holder...
  • Page 26 SPECIAL TOOLS Reference Tool name/Tool No. Illustration pages Rod puller 4-50, 4-52 90890-01437 Universal damping rod bleeding tool set YM-A8703 YM-A8703 Rod puller attachment (M10) 4-50, 4-52 90890-01436 Universal damping rod bleeding tool set YM-A8703 YM-A8703 Ring nut wrench 4-57 90890-01268 Spanner wrench YU-01268...
  • Page 27 Valve guide reamer (4.5 mm) YM-04118 Valve spring compressor 5-24 90890-04109 Sheave holder 5-28, 5-29, 90890-01701 5-31 Primary clutch holder YS-01880-A Flywheel puller 5-28 90890-01404 Flywheel puller YM-01404 Yamaha bond No. 1215 5-29, 5-31, 90890-85505 5-57 ® (Three Bond No.1215 1-18...
  • Page 28 SPECIAL TOOLS Reference Tool name/Tool No. Illustration pages Universal clutch holder 5-41, 5-45 90890-04086 YM-91042 Thickness gauge 5-41 0.15 0.10 0.05 90890-03180 0.20 0.03 0.50 Feeler gauge set 0.25 0.30 YU-26900-9 0.35 0.40 Piston pin puller set 5-60 90890-01304 Piston pin puller YU-01304 YU-01304 Radiator cap tester...
  • Page 29 SPECIAL TOOLS Reference Tool name/Tool No. Illustration pages Pressure gauge 7-10 90890-03153 Pressure gauge YU-03153 Fuel pressure adapter 7-10 90890-03176 YM-03176 Digital circuit tester 7-11 90890-03174 Model 88 Multimeter with tachometer YU-A1927 Ignition checker 8-102 90890-06754 Opama pet-4000 spark checker YM-34487 1-20...
  • Page 30 SPECIAL TOOLS 1-21...

  • Page 31: Specifications

    SPECIFICATIONS GENERAL SPECIFICATIONS ................ 2-1 ENGINE SPECIFICATIONS ................2-2 CHASSIS SPECIFICATIONS ................ 2-10 ELECTRICAL SPECIFICATIONS ..............2-13 TIGHTENING TORQUES ................2-16 GENERAL TIGHTENING TORQUE SPECIFICATIONS......2-16 ENGINE TIGHTENING TORQUES............2-17 CHASSIS TIGHTENING TORQUES............2-21 LUBRICATION POINTS AND LUBRICANT TYPES ........2-25 ENGINE....................

  • Page 32: General Specifications

    GENERAL SPECIFICATIONS EAS20280 GENERAL SPECIFICATIONS Model Model 2C01 (EUR)(ZAF) 2C02 (BEL)(FRA) 2C04 (AUS) Dimensions Overall length 2040 mm (80.3 in) Overall width 700 mm (27.6 in) Overall height 1100 mm (43.3 in) Seat height 850 mm (33.5 in) Wheelbase 1380 mm (54.3 in) Ground clearance 130 mm (5.12 in) Minimum turning radius...

  • Page 33: Engine Specifications

    ENGINE SPECIFICATIONS EAS20290 ENGINE SPECIFICATIONS Engine Engine type Liquid-cooled 4-stroke, DOHC Displacement 599 cm³ (36.55 cu.in) Cylinder arrangement Forward-inclined parallel 4-cylinder Bore × stroke 67.0 × 42.5 mm (2.64 × 1.67 in) Compression ratio 12.8 :1 Standard compression pressure (at sea level) 1550 kPa/400 r/min (220.5 psi/400 r/min) (15.5 kgf/cm²/400 r/min) Minimum–maximum...
  • Page 34 ENGINE SPECIFICATIONS Coolant reservoir capacity (up to the maximum level mark) 0.25 L (0.26 US qt) (0.22 Imp.qt) Radiator cap opening pressure 107.9–137.3 kPa (15.6–19.9 psi) (1.08–1.37 kgf/cm²) Thermostat Valve opening temperature 71 °C (159.8 °F) Valve full open temperature 85 °C (185 °F) Valve lift (full open) More than 8 mm (0.31 in)
  • Page 35 ENGINE SPECIFICATIONS Exhaust B 25.082–25.182 mm (0.9875–0.9914 in) Limit 25.032 mm (0.9855 in) Camshaft runout limit 0.030 mm (0.0012 in) Timing chain Model/number of links 98XRH2015/118 Tensioning system Automatic Valve, valve seat, valve guide Valve clearance (cold) Intake 0.12–0.19 mm (0.0047–0.0075 in) Exhaust 0.16–0.23 mm (0.0063–0.0091 in) Valve dimensions...
  • Page 36 ENGINE SPECIFICATIONS Valve margin thickness D (intake) 0.90–1.10 mm (0.0354–0.0433 in) Limit 0.8 mm (0.03 in) Valve margin thickness D (exhaust) 1.10–1.30 mm (0.0433–0.0512 in) Limit 1.0 mm (0.04 in) Valve stem diameter (intake) 4.475–4.490 mm (0.1762–0.1768 in) Limit 4.460 mm (0.1756 in) Valve stem diameter (exhaust) 4.460–4.475 mm (0.1756–0.1762 in) Limit...
  • Page 37 ENGINE SPECIFICATIONS Spring tilt (intake) 2.5°/1.6 mm Spring tilt (exhaust) 2.5°/1.6 mm Winding direction (intake) Clockwise Winding direction (exhaust) Clockwise Cylinder Bore 67.000–67.010 mm (2.6378–2.6382 in) Taper limit 0.050 mm (0.0020 in) Out of round limit 0.050 mm (0.0020 in) Piston Piston-to-cylinder clearance 0.010–0.035 mm (0.0004–0.0014 in)
  • Page 38 ENGINE SPECIFICATIONS 2nd ring Ring type Taper Dimensions (B × T) 0.80 × 2.50 mm (0.03 × 0.10 in) End gap (installed) 0.70–0.80 mm (0.0276–0.0315 in) Limit 1.00 mm (0.0394 in) Ring side clearance 0.020–0.055 mm (0.0008–0.0022 in) Oil ring Dimensions (B ×...
  • Page 39 ENGINE SPECIFICATIONS Plate quantity 8 pcs Warpage limit 0.10 mm (0.0039 in) Clutch spring free length 55.00 mm (2.17 in) Minimum length 54.00 mm (2.13 in) Spring quantity 6 pcs Transmission Transmission type Constant mesh 6-speed Primary reduction system Spur gear Primary reduction ratio 85/41 (2.073) Secondary reduction system...
  • Page 40 ENGINE SPECIFICATIONS Fuel injection sensor 248–372 Ω at 20 °C (68 °F) Crankshaft position sensor resistance Cylinder identification sensor output voltage (ON) Less than 0.8 V Cylinder identification sensor output voltage (OFF) More than 4.8 V Intake air pressure sensor output voltage 3.15–4.15 V Atmospheric pressure sensor output voltage 3.15–4.15 V...

  • Page 41: Chassis Specifications

    CHASSIS SPECIFICATIONS EAS20300 CHASSIS SPECIFICATIONS Chassis Frame type Diamond Caster angle 24.00° Trail 97.0 mm (3.82 in) Front wheel Wheel type Cast wheel 17M/C × MT3.50 Rim size Rim material Aluminum Wheel travel 120.0 mm (4.72 in) Radial wheel runout limit 1.0 mm (0.04 in) Lateral wheel runout limit 0.5 mm (0.02 in)
  • Page 42 CHASSIS SPECIFICATIONS Front disc brake Disc outside diameter × thickness 310.0 × 4.5 mm (12.20 × 0.18 in) Brake disc thickness limit 4.0 mm (0.16 in) Brake disc deflection limit 0.10 mm (0.0039 in) Brake pad lining thickness (inner) 4.5 mm (0.18 in) Limit 0.5 mm (0.02 in) Brake pad lining thickness (outer)
  • Page 43 CHASSIS SPECIFICATIONS Spring/shock absorber type Coil spring/gas-oil damper Rear shock absorber assembly travel 60.0 mm (2.36 in) Spring free length 163.5 mm (6.44 in) Installed length 152.5 mm (6.00 in) Spring rate K1 98.00 N/mm (559.58 lb/in) (9.99 kgf/mm) Spring stroke K1 0.0–60.0 mm (0.00–2.36 in) Optional spring available Enclosed gas/air pressure (STD)

  • Page 44: Electrical Specifications

    ELECTRICAL SPECIFICATIONS EAS20310 ELECTRICAL SPECIFICATIONS Voltage System voltage 12 V Ignition system Ignition system Transistorized coil ignition (digital) Advancer type Throttle position sensor and electrical Ignition timing (B.T.D.C.) 10.0°/1300 r/min Engine control unit Model/manufacturer TBDF21/DENSO (EUR)(ZAF)(AUS) TBDF23/DENSO (BEL)(FRA) Ignition coil Model/manufacturer F6T558/MITSUBISHI Minimum ignition spark gap...
  • Page 45 ELECTRICAL SPECIFICATIONS Indicator light Neutral indicator light Turn signal indicator light Oil level warning light High beam indicator light Fuel level warning light Coolant temperature warning light Engine trouble warning light Immobilizer system indicator light Shift timing indicator light Electric starting system System type Constant mesh Starter motor...
  • Page 46 ELECTRICAL SPECIFICATIONS Starting circuit cut-off relay Model/manufacturer G8R-30Y-V4/OMRON Headlight relay Model/manufacturer ACM33211M04/MATSUSHITA Fuel pump relay Model/manufacturer G8R-30Y-V4/OMRON Fan motor relay Model/manufacturer ACM33211M05/MATSUSHITA Fuses Main fuse 50.0 A Headlight fuse 15.0 A Taillight fuse 7.5 A Signaling system fuse 10.0 A Ignition fuse 15.0 A 15.0 A ×...

  • Page 47: Tightening Torques

    TIGHTENING TORQUES EAS20320 TIGHTENING TORQUES EAS20330 GENERAL TIGHTENING TORQUE SPECIFICATIONS This chart specifies tightening torques for stan- dard fasteners with a standard ISO thread pitch. Tightening torque specifications for special com- ponents or assemblies are provided for each chapter of this manual. To avoid warpage, tight- en multi-fastener assemblies in a crisscross pat- tern and progressive stages until the specified tightening torque is reached.

  • Page 48: Engine Tightening Torques

    TIGHTENING TORQUES EAS20340 ENGINE TIGHTENING TORQUES Thread Item Q’ty Tightening torque Remarks size Camshaft cap bolt (intake and 10 Nm (1.0 m·kg, 7.2 ft·lb) exhaust) Cylinder head stud bolt (exhaust 15 Nm (1.5 m·kg, 11 ft·lb) pipe assembly) Cylinder head nut (1st) 25 Nm (2.5 m·kg, 18 ft·lb) Cylinder head nut (final) 42 Nm (4.2 m·kg, 30 ft·lb)
  • Page 49 TIGHTENING TORQUES Thread Item Q’ty Tightening torque Remarks size Upper air filter case to lower air 2 Nm (0.2 m·kg, 1.4 ft·lb) filter case bolt Upper air filter case joint bolt 4 Nm (0.4 m·kg, 2.9 ft·lb) Secondary injector fuel rail 5 Nm (0.5 m·kg, 3.6 ft·lb) Locknut (throttle cable) 5 Nm (0.5 m·kg, 3.6 ft·lb)
  • Page 50 TIGHTENING TORQUES Thread Item Q’ty Tightening torque Remarks size Drive sprocket cover bolt 10 Nm (1.0 m·kg, 7.2 ft·lb) Main gallery plug 8 Nm (0.8 m·kg, 5.8 ft·lb) Ventilation chamber cover bolt 12 Nm (1.2 m·kg, 8.7 ft·lb) Oil pipe 12 Nm (1.2 m·kg, 8.7 ft·lb) Crankshaft position sensor bolt 10 Nm (1.0 m·kg, 7.2 ft·lb)
  • Page 51 TIGHTENING TORQUES Cylinder head tightening sequence: Crankcase tightening sequence: 2-20...

  • Page 52: Chassis Tightening Torques

    TIGHTENING TORQUES EAS20350 CHASSIS TIGHTENING TORQUES Thread Item Q’ty Tightening torque Remarks size Engine mounting bolt (front right 45 Nm (4.5 m·kg, 32 ft·lb) side) Engine mounting bolt (front left 45 Nm (4.5 m·kg, 32 ft·lb) side) Engine mounting nut (rear upper 68 Nm (6.8 m·kg, 49 ft·lb) side) Engine mounting nut (rear lower...
  • Page 53 TIGHTENING TORQUES Thread Item Q’ty Tightening torque Remarks size Lower bracket pinch bolt 23 Nm (2.3 m·kg, 17 ft·lb) NOTE Horn and front brake hose joint 10 Nm (1.0 m·kg, 7.2 ft·lb) bolt Front brake hose guide bolt 7 Nm (0.7 m·kg, 5.1 ft·lb) Lower bracket and front brake 10 Nm (1.0 m·kg, 7.2 ft·lb) hose joint bracket bolt...
  • Page 54 TIGHTENING TORQUES Thread Item Q’ty Tightening torque Remarks size Fuel tank bracket and fuel tank 7 Nm (0.7 m·kg, 5.1 ft·lb) bolt Radiator bolt 10 Nm (1.0 m·kg, 7.2 ft·lb) Radiator and coupler holder bolt 5 Nm (0.5 m·kg, 3.6 ft·lb) Radiator bracket and radiator bolt 10 Nm (1.0 m·kg, 7.2 ft·lb) Radiator bracket and frame bolt...
  • Page 55 TIGHTENING TORQUES NOTE: Lower ring nut 1. First, tighten the lower ring nut to approximately 52 Nm (5.2 m·kg, 37 ft·lb) with a torque wrench, then loosen the lower ring nut completely. 2. Retighten the lower ring nut to 14 Nm (1.4 m·kg, 10 ft·lb) with a torque wrench. NOTE: Lower bracket pinch bolt Tighten each bolt to 23 Nm (2.3 m·kg, 17 ft·lb) in the order pinch bolt “1”...

  • Page 56: Lubrication Points And Lubricant Types

    Primary driven gear inner surface Clutch pull rod Transmission gears (wheel and pinion) and collars Main axle and drive axle Shift forks and shift fork guide bars Shift shaft Yamaha bond No.1215 Cylinder head cover mating surface (Three Bond ® No.1215...
  • Page 57 LUBRICATION POINTS AND LUBRICANT TYPES Lubrication point Lubricant Yamaha bond No.1215 Crankshaft position sensor lead grommet (Three Bond ® No.1215 Yamaha bond No.1215 Stator coil lead grommet (Three Bond ® No.1215 2-26...

  • Page 58: Chassis

    LUBRICATION POINTS AND LUBRICANT TYPES EAS20380 CHASSIS Lubrication point Lubricant Steering bearings and upper bearing cover lip Lower bearing dust seal lip Tube guide (throttle grip) inner surface and throttle cables Brake lever pivoting point and metal-to-metal moving parts Clutch cable end Clutch lever pivoting point and metal-to-metal moving parts Relay arm, connecting arm and rear shock absorber spacer Swingarm pivot shaft...
  • Page 59 LUBRICATION POINTS AND LUBRICANT TYPES 2-28...

  • Page 60: Lubrication System Chart And Diagrams

    LUBRICATION SYSTEM CHART AND DIAGRAMS EAS20390 LUBRICATION SYSTEM CHART AND DIAGRAMS EAS20400 ENGINE OIL LUBRICATION CHART 2-29...
  • Page 61 LUBRICATION SYSTEM CHART AND DIAGRAMS 1. Oil strainer 2. Oil pump 3. Relief valve 4. Oil filter 5. Oil cooler 6. Main gallery 7. Oil nozzle 8. Timing chain tensioner 9. Intake camshaft 10. Exhaust camshaft 11. Oil pipe 12. Main axle 13.

  • Page 62: Lubrication Diagrams

    LUBRICATION SYSTEM CHART AND DIAGRAMS EAS20410 LUBRICATION DIAGRAMS 2-31...
  • Page 63 LUBRICATION SYSTEM CHART AND DIAGRAMS 1. Ventilation chamber cover 2. Relief valve 3. Ventilation chamber oil drain pipe 4. Oil cooler 2-32...
  • Page 64 LUBRICATION SYSTEM CHART AND DIAGRAMS 2-33...
  • Page 65 LUBRICATION SYSTEM CHART AND DIAGRAMS 1. Timing chain tensioner 2. Intake camshaft 3. Exhaust camshaft 4. Oil check bolt 5. Oil strainer 6. Ventilation chamber oil drain pipe 7. Oil pipe 8. Oil pump 2-34...
  • Page 66 LUBRICATION SYSTEM CHART AND DIAGRAMS 2-35...
  • Page 67 LUBRICATION SYSTEM CHART AND DIAGRAMS 1. Oil cooler 2. Oil filter 3. Oil pipe 4. Oil pump 5. Oil strainer 2-36...
  • Page 68 LUBRICATION SYSTEM CHART AND DIAGRAMS 2-37...
  • Page 69 LUBRICATION SYSTEM CHART AND DIAGRAMS 1. Main axle 2. Oil pump 3. Oil pipe 4. Ventilation chamber oil drain pipe 5. Relief valve 2-38...
  • Page 70 LUBRICATION SYSTEM CHART AND DIAGRAMS 2-39...
  • Page 71 LUBRICATION SYSTEM CHART AND DIAGRAMS 1. Cylinder head 2. Intake camshaft 3. Exhaust camshaft 4. Crankshaft 5. Oil nozzle 2-40...
  • Page 72 LUBRICATION SYSTEM CHART AND DIAGRAMS 2-41...
  • Page 73 LUBRICATION SYSTEM CHART AND DIAGRAMS 1. Oil pipe 2. Main axle 3. Drive axle 2-42...

  • Page 74: Cooling System Diagrams

    COOLING SYSTEM DIAGRAMS EAS20420 COOLING SYSTEM DIAGRAMS 2-43...
  • Page 75 COOLING SYSTEM DIAGRAMS 1. Radiator inlet hose 2. Radiator inlet pipe 3. Thermostat outlet hose 4. Radiator 2-44...
  • Page 76 COOLING SYSTEM DIAGRAMS 2-45...
  • Page 77 COOLING SYSTEM DIAGRAMS 1. Water pump breather hose 2. Coolant reservoir hose 3. Coolant reservoir 4. Radiator 5. Radiator outlet hose 6. Oil cooler outlet hose 7. Radiator outlet pipe 8. Water jacket joint inlet hose 9. Water pump outlet pipe 10.

  • Page 78: Cable Routing

    CABLE ROUTING EAS20430 CABLE ROUTING 2-47...
  • Page 79 CABLE ROUTING 1. Front brake light switch lead 2. Front brake fluid reservoir hose 3. Right handlebar switch lead 4. Clutch cable 5. Immobilizer unit lead 6. Main switch lead 7. Left handlebar switch lead 8. Clutch switch lead 9. Horn lead 10.
  • Page 80 CABLE ROUTING 60˚ 2-49...
  • Page 81 CABLE ROUTING 1. EXUP servo motor lead K. Fasten the EXUP cables and O sensor lead with a plastic locking tie. Face the end of the plastic 2. Crankshaft position sensor lead locking tie rearward, and then cut off the excess 3.
  • Page 82 CABLE ROUTING 2-51...
  • Page 83 CABLE ROUTING 1. Main switch lead 2. Immobilizer unit lead 3. Left handlebar switch lead 4. Left radiator fan motor lead 5. Wire harness 6. Radiator inlet pipe 7. Fuel tank breather hose 8. Sidestand switch lead 9. AC magneto lead 10.
  • Page 84 CABLE ROUTING 29 30 45˚ 135˚ 2-53...
  • Page 85 CABLE ROUTING 1. Front right turn signal light lead L. Pass the neutral switch lead between the frame and the engine. 2. Right radiator fan motor lead M. To the ECU 3. Throttle position sensor (for throttle valves) lead N. Install both the engine ground lead terminal and 4.
  • Page 86 CABLE ROUTING 2-55...
  • Page 87 CABLE ROUTING 1. Throttle cable (decelerator cable) 2. Throttle cable (accelerator cable) 3. Front brake hose A. Pass the throttle cables between the front fork and the front brake hose. B. When installing the guide on the lower bracket, be sure to pass the front brake hose through it.
  • Page 88 CABLE ROUTING 2-57...
  • Page 89 CABLE ROUTING 1. Fuel tank breather hose (fuel tank to hose joint) 2. Fuel hose (fuel tank to primary injector fuel rail) 3. Crankcase breather hose 4. Fuel tank overflow hose 5. Fuel tank breather hose 6. Fuel tank overflow hose (fuel tank to hose joint) 7.
  • Page 90 CABLE ROUTING 2-59...
  • Page 91 CABLE ROUTING 1. Negative battery lead 2. Main fuse leads 3. Lean angle sensor lead 4. Anti-theft alarm leads (OPTION) 5. ECU (engine control unit) 6. Tail/brake light lead 7. Turn signal light lead (right and left side) 8. License plate light lead 9.
  • Page 92 CABLE ROUTING 2-61...

  • Page 93: Periodic Checks And Adjustments

    PERIODIC CHECKS AND ADJUSTMENTS PERIODIC MAINTENANCE ................3-1 INTRODUCTION ..................3-1 PERIODIC MAINTENANCE AND LUBRICATION CHART....... 3-1 ENGINE ......................3-3 ADJUSTING THE VALVE CLEARANCE ..........3-3 SYNCHRONIZING THE THROTTLE BODIES.......... 3-6 ADJUSTING THE EXHAUST GAS VOLUME ........... 3-7 ADJUSTING THE THROTTLE CABLE FREE PLAY ........ 3-8 CHECKING THE SPARK PLUGS .............
  • Page 94 ELECTRICAL SYSTEM................. 3-35 CHECKING AND CHARGING THE BATTERY........3-35 CHECKING THE FUSES ................ 3-35 REPLACING THE HEADLIGHT BULBS ..........3-35 ADJUSTING THE HEADLIGHT BEAMS..........3-35...

  • Page 96: Periodic Maintenance

    • From 50000 km, repeat the maintenance intervals starting from 10000 km. • Items marked with an asterisk should be performed by a -Yamaha dealer as they require special tools, data and technical skills. ODOMETER READING (× 1000 km)
  • Page 97 PERIODIC MAINTENANCE ODOMETER READING (× 1000 km) ANNU- ITEM CHECK OR MAINTENANCE JOB CHECK √ √ √ √ √ √ 17 * Sidestand switch • Check operation. √ √ √ √ 18 * Front fork • Check operation and for oil leakage. 19 * Shock absorber as- √...

  • Page 98: Engine

    ENGINE EAS20470 ENGINE Valve clearance (cold) Intake 0.12–0.19 mm (0.0047–0.0075 in) EAS20490 ADJUSTING THE VALVE CLEARANCE Exhaust The following procedure applies to all of the 0.16–0.23 mm (0.0063–0.0091 in) valves. M MMM M MMM M MMM M MMM M MMM NOTE: a.
  • Page 99 ENGINE • Measure the valve clearance in the following NOTE: sequence. • Refer to “CAMSHAFTS” on page 5-7. • When removing the timing chain and cam- shafts, fasten the timing chain with a wire to re- Valve clearance measuring sequence Cylinder #1 →...
  • Page 100 ENGINE c. Check the thickness of the current valve pad. NOTE: NOTE: • Lubricate the valve lifter with engine oil. The thickness “a” of each valve pad is marked in • The valve lifter must turn smoothly when rotat- hundredths of millimeters on the side that touch- ed by hand.

  • Page 101: Synchronizing The Throttle Bodies

    ENGINE M MMM M MMM M MMM M MMM M MMM EAS20570 SYNCHRONIZING THE THROTTLE BODIES Basic procedure NOTE: a. Start the engine, warm it up for several min- utes, and then let it run at the specified en- Prior to synchronizing the throttle bodies, the gine idling speed.

  • Page 102: Adjusting The Exhaust Gas Volume

    ENGINE M MMM M MMM M MMM M MMM M MMM • Fuel tank Alternate procedure Refer to “FUEL TANK” on page 7-1. NOTE: • Rider seat Refer to “GENERAL CHASSIS” on page 4-1. Use this alternate procedure if you are unable to adjust the throttle body synchronization using EAS20600 the basic procedure.

  • Page 103: Adjusting The Throttle Cable Free Play

    ENGINE 5. Press the “SELECT” and “RESET” buttons to Throttle cable free play select a cylinder “1”. 3.0–5.0 mm (0.12–0.20 in) NOTE: The selected cylinder number appears on the odometer/trip meter/fuel reserve trip meter/stop- watch LCD. • To decrease the selected cylinder number, press the “RESET”...

  • Page 104: Measuring The Compression Pressure

    ENGINE • Air filter case NOTE: Refer to “AIR FILTER CASE” on page 7-4. Before installing the spark plug, clean the spark • Air induction system solenoid plug and gasket surface. Refer to “AIR INDUCTION SYSTEM” on 8. Install: page 7-13. •...

  • Page 105: Checking The Engine Oil Level

    ENGINE Refer to the following table. Compression gauge Compression pressure (with oil applied into 90890-03081 the cylinder) Engine compression tester Reading Diagnosis YU-33223 Extension Higher than without Piston ring(s) wear or 90890-04136 damage → Repair. Pistons, valves, cylin- der head gasket or Same as without oil piston ring(s) possi- bly defective →...

  • Page 106: Changing The Engine Oil

    ENGINE 5. Start the engine, warm it up for several min- utes, and then turn it off. 6. Check the engine oil level again. NOTE: Before checking the engine oil level, wait a few minutes until the oil has settled. 7.
  • Page 107 ENGINE c. Remove the oil filter cartridge “5” with an oil Shift arm bolt filter wrench “6”. 10 Nm (1.0 m·kg, 7.2 ft·lb) Oil filter wrench 90890-01426 YU-38411 L LLL L LLL L LLL L LLL L LLL 8. Check: •...

  • Page 108: Measuring The Engine Oil Pressure

    ENGINE 6. Measure: EAS20820 MEASURING THE ENGINE OIL PRESSURE • Engine oil pressure 1. Check: (at the following conditions) • Engine oil level Below the minimum level mark → Add the Oil pressure (hot) recommended engine oil to the proper level. 80.0 kPa/1300 r/min (11.6 2.

  • Page 109: Replacing The Air Filter Element

    ENGINE 2. Adjust: EAS20960 REPLACING THE AIR FILTER ELEMENT • Clutch lever free play 1. Remove: • Rider seat M MMM M MMM M MMM M MMM M MMM Refer to “GENERAL CHASSIS” on page 4-1. Handlebar side • Fuel tank a.

  • Page 110: Checking The Throttle Body Joints

    ENGINE EAS21010 ECA14940 CHECKING THE THROTTLE BODY JOINTS CAUTION: The following procedure applies to all of the Make sure the fuel tank breather hose is rout- throttle body joints and intake manifolds. ed correctly. 1. Remove: • Rider seat Refer to “GENERAL CHASSIS” on page 4-1. •...

  • Page 111: Checking The Exhaust System

    ENGINE EAS21080 CHECKING THE EXHAUST SYSTEM The following procedure applies to all of the ex- haust pipe assembly and gaskets. 1. Remove: • Side cowlings • Bottom cowlings Refer to “GENERAL CHASSIS” on page 4-1. 2. Check: • Exhaust pipe assembly “1” •...

  • Page 112: Checking The Coolant Level

    ENGINE NOTE: Locknut (EXUP cable adjusting Check that the projection “a” on the EXUP valve bolt) pulley contacts the stopper “b” (fully open posi- 7 Nm (0.7 m·kg, 5.1 ft·lb) tion). If the projection does not contact the stop- per, adjust the EXUP cable free play. d.

  • Page 113: Checking The Cooling System

    ENGINE 2. Check: • Thermostat outlet hose “4” • Coolant level • Radiator outlet hose “5” The coolant level should be between the • Radiator outlet pipe “6” maximum level mark “a” and minimum level • Oil cooler “7” mark “b”. •...

  • Page 114: Changing The Coolant

    ENGINE 6. Remove: EAS21130 CHANGING THE COOLANT • Coolant reservoir “1” 1. Remove: • Coolant reservoir cap “2” • Right side panel • Right upper side cowling • Right lower side cowling • Right bottom cowling Refer to “GENERAL CHASSIS” on page 4-1. 2.
  • Page 115 ENGINE • If coolant splashes on your clothes, quickly wash it away with water and then with soap and water. • If coolant is swallowed, induce vomiting and get immediate medical attention. ECA13480 CAUTION: • Adding water instead of coolant lowers the antifreeze content of the coolant.

  • Page 116: Chassis

    CHASSIS EAS21140 ECA13490 CHASSIS CAUTION: After adjusting the brake lever position, EAS21150 make sure there is no brake drag. ADJUSTING THE FRONT DISC BRAKE 1. Adjust: L LLL L LLL L LLL L LLL L LLL • Brake lever position EAS21190 (distance “a”...

  • Page 117: Checking The Brake Fluid Level

    CHASSIS EC2C01009 EWA13090 CAUTION: WARNING • Use only the designated brake fluid. Other After adjusting the installed rear master cyl- inder length, make sure there is no brake brake fluids may cause the rubber seals to deteriorate, causing leakage and poor drag.

  • Page 118: Checking The Front Brake Hoses

    CHASSIS 1. Operate the brake. 2. Check: 2. Check: • Brake hose holders “2” Loose connection → Connect. • Rear brake pad Wear limit “a” reached → Replace the brake pads as a set. Refer to “REAR BRAKE” on page 4-29. Limit 1.0 mm (0.04 in) 3.

  • Page 119: Bleeding The Hydraulic Brake System

    CHASSIS L LLL L LLL L LLL L LLL L LLL EAS21360 BLEEDING THE HYDRAULIC BRAKE SYSTEM EWA13100 WARNING Bleed the hydraulic brake system whenever: • the system is disassembled. • a brake hose is loosened, disconnected or replaced. • the brake fluid level is very low. A.

  • Page 120: Adjusting The Shift Pedal

    CHASSIS Bleed screw (front brake master Direction “a” cylinder) Installed shift rod length increases. 6 Nm (0.6 m·kg, 4.3 ft·lb) Direction “b” Bleed screw (front brake caliper) Installed shift rod length decreases. 5 Nm (0.5 m·kg, 3.6 ft·lb) Bleed screw (rear brake caliper) 5 Nm (0.5 m·kg, 3.6 ft·lb) k.

  • Page 121: Lubricating The Drive Chain

    CHASSIS Drive chain slack Drive chain adjusting bolt 35.0–45.0 mm (1.38–1.77 in) 2 Nm (0.2 m·kg, 1.4 ft·lb) f. Tighten the locknuts to specification. NOTE: Measure the drive chain slack halfway between Drive chain adjusting locknut the drive axle and the rear wheel axle. 16 Nm (1.6 m·kg, 11 ft·lb) L LLL L LLL...
  • Page 122 CHASSIS 4. Adjust: d. Check the steering head for looseness or • Steering head binding by turning the front fork all the way in both directions. If any binding is felt, remove M MMM M MMM M MMM M MMM M MMM a.

  • Page 123: Checking The Front Fork

    CHASSIS d. Hold the spring gauge at a 90° angle from the handlebar, pull the spring gauge, and then record the measurement when the handlebar starts to run. Steering head tension 200–500 g 3. Hold the vehicle upright and apply the front brake.
  • Page 124 CHASSIS Direction “a” Direction “a” (turn in) Spring preload is increased (suspen- Rebound damping is increased (sus- sion is harder). pension is harder). Direction “b” Direction “b” (turn out) Spring preload is decreased (suspen- Rebound damping is decreased (sus- sion is softer). pension is softer).

  • Page 125: Adjusting The Rear Shock Absorber Assembly

    CHASSIS Compression damping adjusting Compression damping adjusting positions (fast compression damp- positions (slow compression ing) damping) Minimum Minimum Distance “c” = 8 mm (0.31 in) 16 click(s) out* Standard Standard Distance “c” = 10 mm (0.39 in) 10 click(s) out* Maximum Maximum Distance “c”...
  • Page 126 CHASSIS Spring preload adjusting positions Minimum Standard Maximum L LLL L LLL L LLL L LLL L LLL Compression damping ECA13590 CAUTION: Never go beyond the maximum or minimum adjustment positions. 1. Adjust: • Compression damping (fast compression L LLL L LLL L LLL L LLL...

  • Page 127: Checking The Tires

    CHASSIS 2. Adjust: EWA13180 WARNING • Compression damping (slow compression • The tire pressure should only be checked damping) and regulated when the tire temperature M MMM M MMM M MMM M MMM M MMM a. Turn the adjusting screw “1” in direction “a” or equals the ambient air temperature.

  • Page 128: Checking The Wheels

    CHASSIS and of the same design. No guarantee con- cerning handling characteristics can be giv- en if a tire combination other than one approved by Yamaha is used on this vehicle. Front tire Size 120/70 ZR17M/C (58W) Manufacturer/model DUNLOP/D209F PT 1.

  • Page 129: Checking And Lubricating The Cables

    CHASSIS EWA13260 EAS21720 LUBRICATING THE SIDESTAND WARNING Lubricate the pivoting point and metal-to-metal Never attempt to make any repairs to the moving parts of the sidestand. wheel. Recommended lubricant NOTE: Lithium-soap-based grease After a tire or wheel has been changed or re- placed, always balance the wheel.
  • Page 130 ELECTRICAL SYSTEM EAS21750 EWA13320 ELECTRICAL SYSTEM WARNING Since the headlight bulb gets extremely hot, EAS21760 keep flammable products and your hands CHECKING AND CHARGING THE BATTERY away from the bulb until it has cooled down. Refer to “ELECTRICAL COMPONENTS” on page 8-87.
  • Page 131 ELECTRICAL SYSTEM A. Left headlight B. Right headlight L LLL L LLL L LLL L LLL L LLL 2. Adjust: • Headlight beam (horizontally) M MMM M MMM M MMM M MMM M MMM a. Turn the adjusting screw “1” in direction “a” or “b”.
  • Page 132 ELECTRICAL SYSTEM 3-37...
  • Page 133 CHASSIS GENERAL CHASSIS..................4-1 FRONT WHEEL....................4-5 REMOVING THE FRONT WHEEL............4-7 DISASSEMBLING THE FRONT WHEEL..........4-7 CHECKING THE FRONT WHEEL ............4-7 ASSEMBLING THE FRONT WHEEL............4-8 ADJUSTING THE FRONT WHEEL STATIC BALANCE ......4-8 CHECKING THE FRONT BRAKE DISCS..........4-9 INSTALLING THE FRONT WHEEL (FRONT BRAKE DISCS) ....
  • Page 134 REAR BRAKE ....................4-29 INTRODUCTION ..................4-34 CHECKING THE REAR BRAKE DISC............ 4-34 REPLACING THE REAR BRAKE PADS..........4-34 REMOVING THE REAR BRAKE CALIPER ..........4-35 DISASSEMBLING THE REAR BRAKE CALIPER ........4-35 CHECKING THE REAR BRAKE CALIPER..........4-36 ASSEMBLING THE REAR BRAKE CALIPER ........4-36 INSTALLING THE REAR BRAKE CALIPER...........
  • Page 135 CHAIN DRIVE....................4-69 REMOVING THE DRIVE CHAIN............. 4-70 CHECKING THE DRIVE CHAIN ............. 4-70 CHECKING THE DRIVE SPROCKET............. 4-71 CHECKING THE REAR WHEEL SPROCKET........4-71 CHECKING THE REAR WHEEL DRIVE HUB ........4-71 INSTALLING THE DRIVE CHAIN ............4-71...
  • Page 136 GENERAL CHASSIS EAS21830 GENERAL CHASSIS Removing the seat and battery 7 Nm (0.7 m kg, 5.1 ft • • 7 Nm (0.7 m kg, 5.1 ft • • 7 Nm (0.7 m kg, 5.1 ft • • Order Job/Parts to remove Q’ty Remarks Rider seat...

  • Page 137: General Chassis

    GENERAL CHASSIS Removing the tail/brake light assembly 7 Nm (0.7 m kg, 5.1 ft • • 7 Nm (0.7 m kg, 5.1 ft • • 28 Nm (2.8 m kg, 20 ft • • Order Job/Parts to remove Q’ty Remarks Refer to “GENERAL CHASSIS”...
  • Page 138 GENERAL CHASSIS Removing the tail/brake light assembly 7 Nm (0.7 m kg, 5.1 ft • • 7 Nm (0.7 m kg, 5.1 ft • • 28 Nm (2.8 m kg, 20 ft • • Order Job/Parts to remove Q’ty Remarks Right cowling hole cover Installed for solo riding only.
  • Page 139 GENERAL CHASSIS Removing the side cowlings and front cowling assembly 7 Nm (0.7 m kg, 5.1 ft • • 13 Nm (1.3 m kg, 9.4 ft • • Order Job/Parts to remove Q’ty Remarks Side panel Upper side cowling Lower side cowling Front turn signal light coupler Disconnect.
  • Page 140 FRONT WHEEL EAS21870 FRONT WHEEL Removing the front wheel and brake discs Order Job/Parts to remove Q’ty Remarks NOTE: Place the vehicle on a suitable stand so that the front wheel is elevated. Left front brake hose holder Right front brake hose holder Left front brake caliper Right front brake caliper Front wheel axle pinch bolt...
  • Page 141 FRONT WHEEL Disassembling the front wheel Order Job/Parts to remove Q’ty Remarks Oil seal Wheel bearing Spacer For assembly, reverse the disassembly pro- cedure.

  • Page 142: Front Wheel

    FRONT WHEEL EAS21900 EAS21920 REMOVING THE FRONT WHEEL CHECKING THE FRONT WHEEL 1. Stand the vehicle on a level surface. 1. Check: • Wheel axle EWA13120 WARNING Roll the wheel axle on a flat surface. Bends → Replace. Securely support the vehicle so that there is no danger of it falling over.

  • Page 143: Assembling The Front Wheel

    FRONT WHEEL NOTE: Place the front wheel on a suitable balancing stand. M MMM M MMM M MMM M MMM M MMM a. Spin the front wheel. b. When the front wheel stops, put an “X ” mark at the bottom of the wheel. EAS21960 ASSEMBLING THE FRONT WHEEL 1.

  • Page 144: Checking The Front Brake Discs

    FRONT WHEEL 1. Install: • Front brake disc Front brake disc bolt 18 Nm (1.8 m·kg, 13 ft·lb) ® LOCTITE NOTE: Tighten the brake disc bolts in stages and in a crisscross pattern. b. Turn the front wheel 90° so that the heavy spot is positioned as shown.
  • Page 145 FRONT WHEEL EWA13500 WARNING Front wheel axle 91 Nm (9.1 m·kg, 66 ft·lb) Make sure the brake hose is routed properly. Front wheel axle pinch bolt 21 Nm (2.1 m·kg, 15 ft·lb) EC2C01015 CAUTION: Before tightening the wheel axle, push down hard on the handlebar several times and check if the front fork rebounds smoothly.

  • Page 146: Rear Wheel

    REAR WHEEL EAS22020 REAR WHEEL Removing the rear wheel Order Job/Parts to remove Q’ty Remarks NOTE: Place the vehicle on a suitable stand so that the rear wheel is elevated. Rear brake caliper Drive chain adjusting locknut Loosen. Drive chain adjusting bolt Loosen.
  • Page 147 REAR WHEEL Removing the rear brake disc and rear wheel sprocket Order Job/Parts to remove Q’ty Remarks Rear brake disc Rear wheel sprocket Collar Dust cover Oil seal Bearing Rear wheel drive hub Rear wheel drive hub damper Dust cover Collar For installation, reverse the removal proce- dure.
  • Page 148 REAR WHEEL Disassembling the rear wheel Order Job/Parts to remove Q’ty Remarks Collar Bearing Spacer Oil seal Circlip Bearing For assembly, reverse the disassembly pro- cedure. 4-13...

  • Page 149: Removing The Rear Wheel

    REAR WHEEL EAS22040 EAS22090 REMOVING THE REAR WHEEL CHECKING THE REAR WHEEL 1. Stand the vehicle on a level surface. 1. Check: • Rear wheel axle EWA13120 WARNING • Rear wheel Securely support the vehicle so that there is • Wheel bearings no danger of it falling over.

  • Page 150: Assembling The Rear Wheel

    REAR WHEEL EAS22150 ADJUSTING THE REAR WHEEL STATIC BALANCE NOTE: • After replacing the tire, wheel or both, the rear wheel static balance should be adjusted. • Adjust the rear wheel static balance with the brake disc and rear wheel drive hub installed. 1.
  • Page 151 REAR WHEEL 4. Adjust: • Drive chain slack Refer to “ADJUSTING THE DRIVE CHAIN SLACK” on page 3-25. Drive chain slack 35.0–45.0 mm (1.38–1.77 in) 5. Install: • Rear brake caliper Rear brake caliper bolt (M12) 27 Nm (2.7 m·kg, 19 ft·lb) Rear brake caliper bolt (M8) 22 Nm (2.2 m·kg, 16 ft·lb) ®...

  • Page 152: Front Brake

    FRONT BRAKE EAS22210 FRONT BRAKE Removing the front brake pads Order Job/Parts to remove Q’ty Remarks The following procedure applies to both of the front brake calipers. Brake hose holder Front brake caliper Brake pad clip Brake pad pin Brake pad spring Front brake pad For installation, reverse the removal proce- dure.
  • Page 153 FRONT BRAKE Removing the front brake master cylinder 13 Nm (1.3 m kg, 9.4 ft • • 30 Nm (3.0 m kg, 22 ft • • Order Job/Parts to remove Q’ty Remarks Drain. Brake fluid Refer to “BLEEDING THE HYDRAULIC BRAKE SYSTEM”...
  • Page 154 FRONT BRAKE Disassembling the front brake master cylinder 6 Nm (0.6 m kg, 4.3 ft • • Order Job/Parts to remove Q’ty Remarks Brake master cylinder kit Bleed screw Brake master cylinder body For assembly, reverse the disassembly pro- cedure. 4-19...
  • Page 155 FRONT BRAKE Removing the front brake calipers Order Job/Parts to remove Q’ty Remarks The following procedure applies to both of the front brake calipers. Drain. Brake fluid Refer to “BLEEDING THE HYDRAULIC BRAKE SYSTEM” on page 3-24. Brake hose holder Front brake hose union bolt Copper washer Front brake hose...
  • Page 156 FRONT BRAKE Disassembling the front brake calipers Order Job/Parts to remove Q’ty Remarks The following procedure applies to both of the front brake calipers. Brake pad clip Brake pad pin Brake pad spring Front brake pad Brake caliper piston Brake caliper piston seal Bleed screw For assembly, reverse the disassembly pro- cedure.

  • Page 157: Introduction

    FRONT BRAKE EAS22220 INTRODUCTION EWA14100 WARNING Disc brake components rarely require disas- sembly. Therefore, always follow these pre- ventive measures: • Never disassemble brake components un- less absolutely necessary. • If any connection on the hydraulic brake system is disconnected, the entire brake e.

  • Page 158: Replacing The Front Brake Pads

    FRONT BRAKE NOTE: Brake disc bolt Always install new brake pads, and a brake pad 18 Nm (1.8 m·kg, 13 ft·lb) spring as a set. ® LOCTITE M MMM M MMM M MMM M MMM M MMM a. Connect a clear plastic hose “1” tightly to the d.

  • Page 159: Removing The Front Brake Calipers

    FRONT BRAKE Refer to “CHECKING THE BRAKE FLUID EW2C01005 WARNING LEVEL” on page 3-22. Do not loosen the bolts “3”. 5. Check: • Brake lever operation M MMM M MMM M MMM M MMM M MMM Soft or spongy feeling → Bleed the brake sys- a.

  • Page 160: Assembling The Front Brake Calipers

    FRONT BRAKE • Brake caliper cylinders “2” Front brake hose union bolt Scratches/wear → Replace the brake caliper 30 Nm (3.0 m·kg, 22 ft·lb) assembly. • Brake caliper body “3” EWA13530 Cracks/damage → Replace the brake caliper WARNING assembly. Proper brake hose routing is essential to in- •...

  • Page 161: Removing The Front Brake Master Cylinder

    FRONT BRAKE • Refill with the same type of brake fluid that NOTE: is already in the system. Mixing brake fluids To collect any remaining brake fluid, place a may result in a harmful chemical reaction, container under the master cylinder and the end leading to poor brake performance.

  • Page 162: Installing The Front Brake Master Cylinder

    FRONT BRAKE EAS22540 INSTALLING THE FRONT BRAKE MASTER 15.8˚ CYLINDER 1. Install: • Front brake master cylinder “1” • Front brake master cylinder holder “2” Front brake master cylinder hold- er bolt 13 Nm (1.3 m·kg, 9.4 ft·lb) 3. Fill: NOTE: •...
  • Page 163 FRONT BRAKE 6. Check: • Brake lever operation Soft or spongy feeling → Bleed the brake sys- tem. Refer to “BLEEDING THE HYDRAULIC BRAKE SYSTEM” on page 3-24. 4-28...
  • Page 164 REAR BRAKE EAS22550 REAR BRAKE Removing the rear brake pads Order Job/Parts to remove Q’ty Remarks Screw plug Brake pad pin Rear brake caliper Brake pad shim Brake pad insulator Rear brake pad Brake pad spring For installation, reverse the removal proce- dure.
  • Page 165 REAR BRAKE Removing the rear brake master cylinder 7 Nm (0.7 m kg, 5.1 ft • • 30 Nm (3.0 m kg, 22 ft • • 13 Nm (1.3 m kg, 9.4 ft • • Order Job/Parts to remove Q’ty Remarks Drain.
  • Page 166 REAR BRAKE Disassembling the rear brake master cylinder Order Job/Parts to remove Q’ty Remarks Brake master cylinder kit Brake hose joint Brake master cylinder body For assembly, reverse the disassembly pro- cedure. 4-31...
  • Page 167 REAR BRAKE Removing the rear brake caliper Order Job/Parts to remove Q’ty Remarks Drain. Brake fluid Refer to “BLEEDING THE HYDRAULIC BRAKE SYSTEM” on page 3-24. Rear brake hose union bolt Copper washer Rear brake hose Rear brake caliper Brake pad spring For installation, reverse the removal proce- dure.
  • Page 168 REAR BRAKE Disassembling the rear brake caliper Order Job/Parts to remove Q’ty Remarks Screw plug Brake pad pin Brake pad shim Brake pad insulator Rear brake pad Brake pad spring Brake caliper piston Brake caliper piston seal Bleed screw For assembly, reverse the disassembly pro- cedure.

  • Page 169: Rear Brake

    REAR BRAKE EAS22560 INTRODUCTION Brake disc thickness limit EWA14100 4.5 mm (0.18 in) WARNING Disc brake components rarely require disas- 5. Adjust: sembly. Therefore, always follow these pre- • Brake disc deflection ventive measures: Refer to “CHECKING THE FRONT BRAKE •...

  • Page 170: Removing The Rear Brake Caliper

    REAR BRAKE • Brake pad spring 4. Check: • Brake fluid level NOTE: Below the minimum level mark “a” → Add the Always install new brake pads, brake pad insu- recommended brake fluid to the proper level. lators, brake pad shims, and a brake pad spring Refer to “CHECKING THE BRAKE FLUID as a set.

  • Page 171: Checking The Rear Brake Caliper

    REAR BRAKE • Brake caliper body “3” Cracks/damage → Replace the brake caliper assembly. • Brake fluid delivery passages (brake caliper body) Obstruction → Blow out with compressed air. EWA13610 WARNING Whenever a brake caliper is disassembled, replace the brake caliper piston seals. M MMM M MMM M MMM...

  • Page 172: Installing The Rear Brake Caliper

    REAR BRAKE EAS22670 INSTALLING THE REAR BRAKE CALIPER Recommended fluid 1. Install: DOT 4 • Rear brake caliper “1” (temporarily) EWA13090 WARNING • Copper washers • Use only the designated brake fluid. Other • Rear brake hose “2” brake fluids may cause the rubber seals to •...

  • Page 173: Removing The Rear Brake Master Cylinder

    REAR BRAKE EAS22700 EAS22730 REMOVING THE REAR BRAKE MASTER ASSEMBLING THE REAR BRAKE MASTER CYLINDER CYLINDER EWA13520 NOTE: WARNING Before removing the rear brake master cylinder, • Before installation, all internal brake com- drain the brake fluid from the entire brake sys- ponents should be cleaned and lubricated tem.
  • Page 174 REAR BRAKE EWA13090 WARNING • Use only the designated brake fluid. Other brake fluids may cause the rubber seals to deteriorate, causing leakage and poor brake performance. • Refill with the same type of brake fluid that is already in the system. Mixing brake fluids may result in a harmful chemical reaction, leading to poor brake performance.

  • Page 175: Handlebars

    HANDLEBARS EAS22850 HANDLEBARS Removing the handlebars 13 Nm (1.3 m kg, 9.4 ft 115 Nm (11.5 m kg, 85 ft • • • • 13 Nm (1.3 m kg, 9.4 ft 26 Nm (2.6 m kg, 19 ft • • •...
  • Page 176 HANDLEBARS Removing the handlebars 13 Nm (1.3 m kg, 9.4 ft 115 Nm (11.5 m kg, 85 ft • • • • 13 Nm (1.3 m kg, 9.4 ft 26 Nm (2.6 m kg, 19 ft • • • • 11 Nm (1.1 m kg, 8.0 ft •...

  • Page 177: Removing The Handlebars

    HANDLEBARS • Align the mating surfaces of the brake master EAS22870 REMOVING THE HANDLEBARS cylinder holder with the punch mark “b” on the 1. Stand the vehicle on a level surface. handlebar. EWA13120 • First, tighten the upper bolt, then the lower bolt. WARNING Securely support the vehicle so that there is no danger of it falling over.
  • Page 178 HANDLEBARS M MMM M MMM M MMM M MMM M MMM NOTE: a. Apply a thin coat of rubber adhesive onto the There should be 1–3 mm (0.04–0.12 in) of clear- end of the left handlebar. ance “a” between the throttle grip and the right b.

  • Page 179: Front Fork

    FRONT FORK EAS22950 FRONT FORK Removing the front fork legs 13 Nm (1.3 m kg, 9.4 ft • • 32 Nm (3.2 m kg, 23 ft • • 26 Nm (2.6 m kg, 19 ft • • 20 Nm (2.0 m kg, 14 ft •...
  • Page 180 FRONT FORK Disassembling the front fork legs 25 Nm (2.5 m kg, 18 ft • • 20 Nm (2.0 m kg, 14 ft • • 35 Nm (3.5 m kg, 25 ft • • Order Job/Parts to remove Q’ty Remarks The following procedure applies to both of the front fork legs.
  • Page 181 FRONT FORK Disassembling the front fork legs 25 Nm (2.5 m kg, 18 ft • • 20 Nm (2.0 m kg, 14 ft • • 35 Nm (3.5 m kg, 25 ft • • Order Job/Parts to remove Q’ty Remarks Inner tube For assembly, reverse the disassembly pro- cedure.

  • Page 182: Removing The Front Fork Legs

    FRONT FORK 1. Position the collar “1” as shown in the illustra- EAS22970 REMOVING THE FRONT FORK LEGS tion by turning the spring preload adjusting The following procedure applies to both of the bolt “2” counterclockwise until it stops. front fork legs. 1.

  • Page 183: Checking The Front Fork Legs

    FRONT FORK 5. Remove: NOTE: • Oil seal clip “1” Loosen the nut using a proper tool that has a (with a flat-head screwdriver) thickness of 3 mm (0.12 in) or less. d. Remove the cap bolt. EAS23010 CHECKING THE FRONT FORK LEGS e.

  • Page 184: Assembling The Front Fork Legs

    FRONT FORK ECA14200 CAUTION: • The front fork leg has a built-in damper ad- justing rod and a very sophisticated inter- nal construction, which are particularly sensitive to foreign material. • When disassembling and assembling the front fork leg, do not allow any foreign ma- terial to enter the front fork.
  • Page 185 FRONT FORK • Before installing the oil seal, cover the top of the front fork leg with a plastic bag to protect the oil seal during installation. 8. Install: • Dust seal “1” (with the fork seal driver weight “2”) Fork seal driver 90890-01442 Adjustable fork seal driver (36–46...
  • Page 186 FRONT FORK 10.Fully compress the front fork leg. 11.Fill: • Front fork leg (with the specified amount of the recom- mended fork oil) Quantity 465.0 cm³ (15.72 US oz) (16.37 Imp.oz) Recommended oil Ohlins R & T43 15.Install: • Spring seat “1” ECA14230 •...

  • Page 187: Installing The Front Fork Legs

    FRONT FORK EC2C01013 CAUTION: Rod puller 90890-01437 When tightening the spring preload adjust- Universal damping rod bleeding ing bolt “10” into the cap bolt, be sure not to tool set break the projections “c” on the collar “11”. YM-A8703 Rod puller attachment (M10) NOTE: 90890-01436 Hold the nut “4”...
  • Page 188 FRONT FORK • Plastic locking tie “2” NOTE: NOTE: Tighten each bolt to 23 Nm (2.3 m·kg, 17 ft·lb) in the order pinch bolt “1” → pinch bolt “2” → pinch • Fasten the left handlebar switch lead to the left bolt “1”.

  • Page 189: Steering Head

    STEERING HEAD EAS23090 STEERING HEAD Removing the lower bracket 115 Nm (11.5 m kg, 85 ft • • 1st 52 Nm (5.2 m kg, 37 ft • • 2nd 14 Nm (1.4 m kg, 10 ft • • 10 Nm (1.0 m kg, 7.2 ft •...
  • Page 190 STEERING HEAD Removing the lower bracket 115 Nm (11.5 m kg, 85 ft • • 1st 52 Nm (5.2 m kg, 37 ft • • 2nd 14 Nm (1.4 m kg, 10 ft • • 10 Nm (1.0 m kg, 7.2 ft •...
  • Page 191 STEERING HEAD Removing the lower bracket 115 Nm (11.5 m kg, 85 ft • • 1st 52 Nm (5.2 m kg, 37 ft • • 2nd 14 Nm (1.4 m kg, 10 ft • • 10 Nm (1.0 m kg, 7.2 ft •...

  • Page 192: Removing The Lower Bracket

    STEERING HEAD 3. Replace: EAS23110 REMOVING THE LOWER BRACKET • Bearings 1. Stand the vehicle on a level surface. • Bearing races EWA13120 M MMM M MMM M MMM M MMM M MMM WARNING a. Remove the bearing race from the steering Securely support the vehicle so that there is head pipe “1”...
  • Page 193 STEERING HEAD 2. Install: NOTE: • Lower ring nut “1” Make sure that the tab “a” on the front brake • Rubber washer “2” hose joint bracket contacts the side “b” of the • Upper ring nut “3” front brake hose joint. •...

  • Page 194: Rear Shock Absorber Assembly

    REAR SHOCK ABSORBER ASSEMBLY EAS23160 REAR SHOCK ABSORBER ASSEMBLY Removing the rear shock absorber assembly 40 Nm (4.0 m kg, 29 ft • • 44 Nm (4.4 m kg, 32 ft • • 40 Nm (4.0 m kg, 29 ft •...
  • Page 195 REAR SHOCK ABSORBER ASSEMBLY Removing the rear shock absorber assembly 40 Nm (4.0 m kg, 29 ft • • 44 Nm (4.4 m kg, 32 ft • • 40 Nm (4.0 m kg, 29 ft • • 16 Nm (1.6 m kg, 11 ft •...

  • Page 196: Handling The Rear Shock Absorber

    REAR SHOCK ABSORBER ASSEMBLY EAS23180 NOTE: HANDLING THE REAR SHOCK ABSORBER Place the vehicle on a suitable stand so that the EWA13740 WARNING rear wheel is elevated. This rear shock absorber contains highly 2. Remove: compressed nitrogen gas. Before handling •...

  • Page 197: Checking The Connecting Arm And Relay Arm

    REAR SHOCK ABSORBER ASSEMBLY • Spring Damage/wear → Replace the rear shock ab- sorber assembly. • Bushing Damage/wear → Replace. • Spacer Damage/scratches → Replace. • Bolts Bends/damage/wear → Replace. EAS23260 CHECKING THE CONNECTING ARM AND RELAY ARM 1. Check: •...
  • Page 198 REAR SHOCK ABSORBER ASSEMBLY 4. Tighten: • Spacer bolt Spacer bolt 16 Nm (1.6 m·kg, 11 ft·lb) • Rear shock absorber assembly lower nut Rear shock absorber assembly lower nut 40 Nm (4.0 m·kg, 29 ft·lb) • Rear shock absorber assembly upper nut Rear shock absorber assembly upper nut 44 Nm (4.4 m·kg, 32 ft·lb)

  • Page 199: Swingarm

    SWINGARM EAS23330 SWINGARM Removing the swingarm 7 Nm (0.7 m kg, 5.1 ft • • 95 Nm (9.5 m kg, 68 ft • • 16 Nm (1.6 m kg, 11 ft • • 70 Nm (7.0 m kg, 50 ft •...
  • Page 200 SWINGARM Removing the swingarm 7 Nm (0.7 m kg, 5.1 ft • • 95 Nm (9.5 m kg, 68 ft • • 16 Nm (1.6 m kg, 11 ft • • 70 Nm (7.0 m kg, 50 ft • • 7 Nm (0.7 m kg, 5.1 ft •...

  • Page 201: Removing The Swingarm

    SWINGARM 4. Remove: EAS23350 REMOVING THE SWINGARM • Swingarm pivot shaft ring nut “1” 1. Stand the vehicle on a level surface. NOTE: EWA13120 WARNING Loosen the swingarm pivot shaft ring nut with the ring nut wrench “2”. Securely support the vehicle so that there is no danger of it falling over.

  • Page 202: Installing The Swingarm

    SWINGARM 3. Wash: • Pivot shaft • Dust covers • Spacers • Washers • Bearings Recommended cleaning solvent Kerosene 4. Check: • Dust covers 5. Swingarm • Spacers 6. Swingarm pivot shaft • Oil seals 7. Bolt Damage/wear → Replace. A.
  • Page 203 SWINGARM Swingarm pivot shaft ring nut 95 Nm (9.5 m·kg, 68 ft·lb) NOTE: • Lubricate the swingarm pivot ring nut threads and mating surfaces with lithium-soap-based grease. • Tighten the swingarm pivot shaft ring nut with the ring nut wrench “2”. Ring nut wrench 90890-01507 5.
  • Page 204 CHAIN DRIVE EAS23400 CHAIN DRIVE Removing the drive sprocket and drive chain 10 Nm (1.0 m kg, 7.2 ft • • 85 Nm (8.5 m kg, 61 ft • • 10 Nm (1.0 m kg, 7.2 ft • • Order Job/Parts to remove Q’ty Remarks...
  • Page 205 CHAIN DRIVE EAS23410 REMOVING THE DRIVE CHAIN 1. Stand the vehicle on a level surface. EWA13120 WARNING Securely support the vehicle so that there is no danger of it falling over. NOTE: Place the vehicle on a suitable stand so that the rear wheel is elevated.
  • Page 206 CHAIN DRIVE EAS23460 CHECKING THE DRIVE SPROCKET 1. Check: • Drive sprocket More than 1/4 tooth “a” wear → Replace the drive chain sprockets as a set. Bent teeth → Replace the drive chain sprock- ets as a set. b. Correct 1.
  • Page 207 CHAIN DRIVE 4-72...
  • Page 208 CHAIN DRIVE 4-73...

  • Page 209: Engine

    ENGINE ENGINE REMOVAL ..................5-1 INSTALLING THE ENGINE............... 5-6 CAMSHAFTS....................5-7 REMOVING THE CAMSHAFTS..............5-9 CHECKING THE CAMSHAFTS ..............5-9 CHECKING THE TIMING CHAIN, CAMSHAFT SPROCKETS, AND TIMING CHAIN GUIDES ................ 5-11 CHECKING THE TIMING CHAIN TENSIONER........5-11 INSTALLING THE CAMSHAFTS ............5-12 CYLINDER HEAD..................
  • Page 210 CLUTCH ......................5-37 REMOVING THE CLUTCH ..............5-41 CHECKING THE FRICTION PLATES............. 5-41 CHECKING THE CLUTCH PLATES ............5-41 CHECKING THE CLUTCH SPRINGS............. 5-42 CHECKING THE CLUTCH HOUSING ............ 5-43 CHECKING THE CLUTCH BOSS............5-43 CHECKING THE PRESSURE PLATE ............ 5-43 CHECKING THE PRIMARY DRIVE GEAR..........
  • Page 211 TRANSMISSION.................... 5-71 REMOVING THE TRANSMISSION ............5-76 CHECKING THE SHIFT FORKS............. 5-76 CHECKING THE SHIFT DRUM ASSEMBLY.......... 5-76 CHECKING THE TRANSMISSION ............5-77 ASSEMBLING THE MAIN AXLE AND DRIVE AXLE ......5-77 INSTALLING THE TRANSMISSION ............5-78...

  • Page 212: Engine Removal

    ENGINE REMOVAL EAS23710 ENGINE REMOVAL Removing the exhaust pipe assembly 7 Nm (0.7 m kg, 5.1 ft • • 7 Nm (0.7 m kg, 5.1 ft • • 8 Nm (0.8 m kg, 5.8 ft • • 45 Nm (4.5 m kg, 32 ft •...
  • Page 213 ENGINE REMOVAL Removing the exhaust pipe assembly 7 Nm (0.7 m kg, 5.1 ft • • 7 Nm (0.7 m kg, 5.1 ft • • 8 Nm (0.8 m kg, 5.8 ft • • 45 Nm (4.5 m kg, 32 ft •...
  • Page 214 ENGINE REMOVAL Disconnecting the leads and hoses 10 Nm (1.0 m kg, 7.2 ft • • 10 Nm (1.0 m kg, 7.2 ft • • 70 Nm (7.0 m kg, 50 ft • • 10 Nm (1.0 m kg, 7.2 ft •...
  • Page 215 ENGINE REMOVAL Disconnecting the leads and hoses 10 Nm (1.0 m kg, 7.2 ft • • 10 Nm (1.0 m kg, 7.2 ft • • 70 Nm (7.0 m kg, 50 ft • • 10 Nm (1.0 m kg, 7.2 ft •...
  • Page 216 ENGINE REMOVAL Removing the engine 45 Nm (4.5 m kg, 32 ft • • 68 Nm (6.8 m kg, 49 ft • • 10 11 45 Nm (4.5 m kg, 32 ft • • 68 Nm (6.8 m kg, 49 ft •...

  • Page 217: Installing The Engine

    ENGINE REMOVAL EAS23720 INSTALLING THE ENGINE 1. Install: • Engine “1” • Engine mounting bolt (rear lower side) “2” • Engine mounting bolt (rear upper side) “3” • Engine mounting collars (inside) “4” 10 9 • Engine mounting collars (outside) “5” •...

  • Page 218: Camshafts

    CAMSHAFTS EAS23760 CAMSHAFTS Removing the cylinder head cover 8 Nm (0.8 m kg, 5.8 ft • • 12 Nm (1.2 m kg, 8.7 ft • • 13 Nm (1.3 m kg, 9.4 ft • • Order Job/Parts to remove Q’ty Remarks Radiator Refer to “RADIATOR”...
  • Page 219 CAMSHAFTS Removing the camshafts 10 Nm (1.0 m kg, 7.2 ft • • (10) 12 Nm (1.2 m kg, 8.7 ft • • (10) 24 Nm (2.4 m kg, 17 ft • • 10 Nm (1.0 m kg, 7.2 ft •...

  • Page 220: Removing The Camshafts

    CAMSHAFTS EAS23810 ECA13720 REMOVING THE CAMSHAFTS CAUTION: 1. Remove: To prevent damage to the cylinder head, • Pickup rotor cover camshafts or camshaft caps, loosen the Refer to “PICKUP ROTOR” on page 5-30. camshaft cap bolts in stages and in a criss- 2.
  • Page 221 CAMSHAFTS Camshaft lobe dimensions Intake A 33.725–33.875 mm (1.3278– 1.3337 in) Limit 33.675 mm (1.3258 in) Intake B 25.225–25.325 mm (0.9931– 0.9970 in) Limit 4. Measure: 25.175 mm (0.9911 in) • Camshaft-journal-to-camshaft-cap clearance Exhaust A Out of specification → Measure the camshaft 32.925–33.075 mm (1.2963–...

  • Page 222: Checking The Timing Chain, Camshaft Sprockets, And Timing Chain Guides

    CAMSHAFTS L LLL L LLL L LLL L LLL L LLL a. 1/4 tooth b. Correct 5. Measure: 1. Timing chain roller • Camshaft journal diameter “a” Out of specification → Replace the camshaft. 2. Camshaft sprocket Within specification → Replace the cylinder 3.

  • Page 223: Installing The Camshafts

    CAMSHAFTS NOTE: Prior to installing the timing chain tensioner rod, drain the engine oil from the timing chain ten- sioner housing. M MMM M MMM M MMM M MMM M MMM a. Install the timing chain tensioner springs, tim- ing chain tensioner spring seat, and timing chain tensioner rod “1”.
  • Page 224 CAMSHAFTS 2. Install: • Timing chain “1” • Exhaust camshaft “2” • Intake camshaft “3” (with the camshaft sprockets temporarily tightened) NOTE: • Make sure the match marks “a” on the cam- shaft sprockets are aligned with the cylinder head edge “b”. 4.
  • Page 225 CAMSHAFTS 6. Rotate the crankshaft a few times to release the timing chain tensioner rod. 9. Measure: • Valve clearance Out of specification → Adjust. NOTE: Refer to “ADJUSTING THE VALVE CLEAR- If the engine is not disassembled, set the engine ANCE”...

  • Page 226: Cylinder Head

    CYLINDER HEAD EAS24100 CYLINDER HEAD Removing the cylinder head 1st 25 Nm (2.5 m kg, 18 ft 1st 30 Nm (3.0 m kg, 22 ft • • • • 2nd 60 Nm (6.0 m kg, 43 ft 2nd 42 Nm (4.2 m kg, 30 ft •...

  • Page 227: Removing The Cylinder Head

    CYLINDER HEAD EAS24120 REMOVING THE CYLINDER HEAD Warpage limit 1. Remove: 0.05 mm (0.0020 in) • Cylinder head bolts • Cylinder head nuts NOTE: • Loosen the nuts, cap nuts, and bolts in de- creasing numerical order (refer to the numbers in the illustration).
  • Page 228 CYLINDER HEAD Cylinder head cap nut (1st) 30 Nm (3.0 m·kg, 22 ft·lb) Cylinder head cap nut (final) 60 Nm (6.0 m·kg, 43 ft·lb) • Cylinder head bolts “11”, “12” Cylinder head bolt 12 Nm (1.2 m·kg, 8.7 ft·lb) NOTE: Tighten the cylinder head nuts, cap nuts, and bolts in the proper tightening sequence as shown and torque them in two stages.
  • Page 229 VALVES AND VALVE SPRINGS EAS24270 VALVES AND VALVE SPRINGS Removing the valves and valve springs Order Job/Parts to remove Q’ty Remarks Cylinder head Refer to “CYLINDER HEAD” on page 5-15. Valve lifter Valve pad Valve cotter Upper spring seat Intake valve spring Exhaust valve spring Intake valve Exhaust valve...

  • Page 230: Valves And Valve Springs

    VALVES AND VALVE SPRINGS EAS24280 NOTE: REMOVING THE VALVES Remove the valve cotters by compressing the The following procedure applies to all of the valve spring with the valve spring compressor valves and related components. “1” and the valve spring compressor attachment NOTE: “2”.
  • Page 231 VALVES AND VALVE SPRINGS 1. Measure: • Valve-stem-to-valve-guide clearance Out of specification → Replace the valve guide. • Valve-stem-to-valve-guide clearance = Valve guide inside diameter “a” - Valve stem diameter “b” Valve-stem-to-valve-guide clear- ance (intake) b. Install the new valve guide with the valve 0.010–0.037 mm (0.0004–0.0015 guide installer “2”...

  • Page 232: Checking The Valve Seats

    VALVES AND VALVE SPRINGS • If the valve is removed or replaced, always re- Valve guide remover (ø4.5) place the valve stem seal. 90890-04116 Valve guide remover (4.5 mm) Valve stem runout YM-04116 0.040 mm (0.0016 in) Valve guide installer (ø4.5) 90890-04117 Valve guide installer (4.5 mm) YM-04117...

  • Page 233: Checking The Valve Springs

    VALVES AND VALVE SPRINGS NOTE: For the best lapping results, lightly tap the valve seat while rotating the valve back and forth be- tween your hands. b. Install the valve into the cylinder head. c. Press the valve through the valve guide and onto the valve seat to make a clear impres- sion.

  • Page 234: Checking The Valve Lifters

    VALVES AND VALVE SPRINGS 1. Measure: 3. Measure: • Valve spring free length “a” • Valve spring tilt “a” Out of specification → Replace the valve Out of specification → Replace the valve spring. spring. Free length (intake) Spring tilt (intake) 37.47 mm (1.48 in) 2.5°/1.6 mm Limit...
  • Page 235 VALVES AND VALVE SPRINGS Valve spring compressor 90890-04019 YM-04019 Valve spring compressor 90890-04109 Valve spring compressor attach- ment 90890-04108 Valve spring compressor adapt- er 22 mm 3. Install: YM-04108 • Lower spring seat “1” • Valve stem seal “2” • Valve “3” •...
  • Page 236 VALVES AND VALVE SPRINGS • Each valve lifter and valve pad must be rein- stalled in its original position. 5-25...

  • Page 237: Generator And Starter Clutch

    GENERATOR AND STARTER CLUTCH EAS24480 GENERATOR AND STARTER CLUTCH Removing the generator and starter clutch 12 Nm (1.2 m kg, 8.7 ft • • 10 Nm (1.0 m kg, 7.2 ft • • 10 Nm (1.0 m kg, 7.2 ft •...
  • Page 238 GENERATOR AND STARTER CLUTCH Removing the generator and starter clutch 12 Nm (1.2 m kg, 8.7 ft • • 10 Nm (1.0 m kg, 7.2 ft • • 10 Nm (1.0 m kg, 7.2 ft • • 70 Nm (7.0 m kg, 50 ft •...

  • Page 239: Removing The Generator

    GENERATOR AND STARTER CLUTCH EAS24490 EAS24570 REMOVING THE GENERATOR CHECKING THE STARTER CLUTCH 1. Remove: 1. Check: • Generator rotor bolt “1” • Starter clutch rollers Damage/wear → Replace. • Washer 2. Check: NOTE: • Starter clutch idle gear While holding the generator rotor “2” with the •...

  • Page 240: Installing The Generator

    GENERATOR AND STARTER CLUTCH Yamaha bond No. 1215 90890-85505 ® (Three Bond No.1215 EAS24500 INSTALLING THE GENERATOR 1. Install: • Generator rotor • Washer • Generator rotor bolt NOTE: • Clean the tapered portion of the crankshaft and the generator rotor hub.

  • Page 241: Pickup Rotor

    PICKUP ROTOR EAS24520 PICKUP ROTOR Removing the pickup rotor 35 Nm (3.5 m kg, 25 ft • • 15 Nm (1.5 m kg, 11 ft • • 12 Nm (1.2 m kg, 8.7 ft • • 10 Nm (1.0 m kg, 7.2 ft •...

  • Page 242: Removing The Pickup Rotor

    When installing the pickup rotor, align the 3. Apply: groove “a” in the crankshaft with the projection • Sealant “b” on the pickup rotor. (onto the crankshaft position sensor lead grommet) Yamaha bond No. 1215 90890-85505 ® (Three Bond No.1215 5-31...
  • Page 243 PICKUP ROTOR 5-32...

  • Page 244: Electric Starter

    ELECTRIC STARTER EAS24780 ELECTRIC STARTER Removing the starter motor 10 Nm (1.0 m kg, 7.2 ft • • Order Job/Parts to remove Q’ty Remarks Refer to “GENERAL CHASSIS” on page Rider seat 4-1. Air filter case Refer to “AIR FILTER CASE” on page 7-4. Fuel tank Refer to “FUEL TANK”...
  • Page 245 ELECTRIC STARTER Disassembling the starter motor Order Job/Parts to remove Q’ty Remarks O-ring Starter motor front cover Lock washer Oil seal Bearing Washer set Starter motor yoke Armature assembly Gasket Washer set Brush holder (along with the brushes) Starter motor rear cover For assembly, reverse the disassembly pro- cedure.

  • Page 246: Checking The Starter Motor

    ELECTRIC STARTER EAS24790 CHECKING THE STARTER MOTOR Pocket tester 1. Check: 90890-03112 • Commutator Analog pocket tester Dirt → Clean with 600 grit sandpaper. YU-03112-C 2. Measure: • Commutator diameter “1” Armature coil Out of specification → Replace the starter Commutator resistance “1”...

  • Page 247: Assembling The Starter Motor

    ELECTRIC STARTER 7. Check: • Gear teeth Damage/wear → Replace the gear. 8. Check: • Bearing • Oil seal Damage/wear → Replace the defective part(s). EAS24800 ASSEMBLING THE STARTER MOTOR 1. Install: • Starter motor yoke “1” NOTE: Align the tab “a” on the brush holder with the slot “b”...

  • Page 248: Clutch

    CLUTCH EAS25060 CLUTCH Removing the clutch cover 12 Nm (1.2 m kg, 8.7 ft • • 12 Nm (1.2 m kg, 8.7 ft • • 12 Nm (1.2 m kg, 8.7 ft • • Order Job/Parts to remove Q’ty Remarks Refer to “GENERAL CHASSIS”...
  • Page 249 CLUTCH Removing the pull lever shaft Order Job/Parts to remove Q’ty Remarks Circlip Pull lever shaft Oil seal Bearing Bearing For installation, reverse the removal proce- dure. 5-38...
  • Page 250 CLUTCH Removing the clutch 115 Nm (11.5 m kg, 85 ft • • 12 Nm (1.2 m kg, 8.7 ft • • 25 Nm (2.5 m kg, 18 ft • • 8 Nm (0.8 m kg, 5.8 ft • • Order Job/Parts to remove Q’ty...
  • Page 251 CLUTCH Removing the clutch 115 Nm (11.5 m kg, 85 ft • • 12 Nm (1.2 m kg, 8.7 ft • • 25 Nm (2.5 m kg, 18 ft • • 8 Nm (0.8 m kg, 5.8 ft • • Order Job/Parts to remove Q’ty...

  • Page 252: Removing The Clutch

    CLUTCH EAS25070 EAS25100 REMOVING THE CLUTCH CHECKING THE FRICTION PLATES 1. Remove: The following procedure applies to all of the fric- • Friction plates tion plates. • Clutch plates 1. Check: • Friction plate NOTE: Damage/wear → Replace the friction plates Be sure to mark the friction plates and clutch as a set.

  • Page 253: Checking The Clutch Springs

    CLUTCH NOTE: Clutch plate “2” The clutch plate thickness specification listed Part No. Thickness above is for the plates with the standard thick- ness only. If a clutch plate with one of the other 3J2-16324-00 2.0 mm (0.079 in) STD two plate thicknesses is installed, use 1.50–1.70 168-16324-00 2.3 mm (0.091 in)

  • Page 254: Checking The Clutch Housing

    CLUTCH EAS25150 CHECKING THE CLUTCH HOUSING 1. Check: • Clutch housing dogs Damage/pitting/wear → Deburr the clutch housing dogs or replace the clutch housing. NOTE: Pitting on the clutch housing dogs will cause er- ratic clutch operation. EAS25200 CHECKING THE PRIMARY DRIVE GEAR 1.

  • Page 255: Checking The Oil Pump Drive Sprocket And Oil Pump Drive Chain

    CLUTCH NOTE: Fit the projections “a” on the clutch boss into the grooves “b” in the clutch boss plate. 2. Check: • Bearing Damage/wear → Replace. 3. Install: ET2C01011 CHECKING THE OIL PUMP DRIVE • Springs “1” SPROCKET AND OIL PUMP DRIVE CHAIN NOTE: 1.
  • Page 256 CLUTCH • Stake the clutch boss nut at a cutout “a” in the main axle. Universal clutch holder 90890-04086 YM-91042 8. Install: • Seat plate • Clutch springs • Clutch spring bolts Clutch spring bolt 8 Nm (0.8 m·kg, 5.8 ft·lb) 5.
  • Page 257 CLUTCH 10.Install: • Pull lever spring “1” • Pull lever “2” • Washer • Circlip NOTE: • Make sure that the mark “a” on the pull lever is facing up. • When installing the pull lever, push it and check that its punch mark “b” aligns with the mark “c”...

  • Page 258: Shift Shaft

    SHIFT SHAFT EAS25410 SHIFT SHAFT Removing the shift shaft and stopper lever 22 Nm (2.2 m kg, 16 ft • • Order Job/Parts to remove Q’ty Remarks Shift arm Refer to “ENGINE REMOVAL” on page 5-1. Clutch housing Refer to “CLUTCH” on page 5-37. Circlip Washer Shift shaft...
  • Page 259 SHIFT SHAFT Removing the shift shaft and stopper lever 22 Nm (2.2 m kg, 16 ft • • Order Job/Parts to remove Q’ty Remarks Bearing For installation, reverse the removal proce- dure. 5-48...

  • Page 260: Checking The Shift Shaft

    SHIFT SHAFT EAS25420 CHECKING THE SHIFT SHAFT 1. Check: • Shift shaft Bends/damage/wear → Replace. • Shift shaft spring Damage/wear → Replace. EAS25430 CHECKING THE STOPPER LEVER 1. Check: • Stopper lever Bends/damage → Replace. Roller turns roughly → Replace the stopper lever.

  • Page 261: Oil Pump

    OIL PUMP EAS24920 OIL PUMP Removing the oil pan and oil pump 12 Nm (1.2 m kg, 8.7 ft • • 12 Nm (1.2 m kg, 8.7 ft • • (10) 12 Nm (1.2 m kg, 8.7 ft • • 43 Nm (4.3 m kg, 31 ft 10 Nm (1.0 m...
  • Page 262 OIL PUMP Removing the oil pan and oil pump 12 Nm (1.2 m kg, 8.7 ft • • 12 Nm (1.2 m kg, 8.7 ft • • (10) 12 Nm (1.2 m kg, 8.7 ft • • 43 Nm (4.3 m kg, 31 ft 10 Nm (1.0 m kg, 7.2 ft...
  • Page 263 OIL PUMP Disassembling the oil pump Order Job/Parts to remove Q’ty Remarks Oil pump housing cover Oil pump inner rotor Oil pump outer rotor Washer Oil pump housing Oil pump driven sprocket For assembly, reverse the disassembly pro- cedure. 5-52...

  • Page 264: Removing The Oil Pan

    OIL PUMP EAS24930 REMOVING THE OIL PAN Inner-rotor-to-outer-rotor-tip 1. Remove: clearance • Oil level switch lead holder Less than 0.12 mm (0.0047 in) • Bottom cowling brackets Limit 0.20 mm (0.0079 in) • Oil pan Outer-rotor-to-oil-pump-housing • Oil pan gasket clearance NOTE: 0.090–0.150 mm (0.0035–0.0059...

  • Page 265: Checking The Oil Pipes

    OIL PUMP EAS24980 EAS25050 CHECKING THE OIL PIPES INSTALLING THE OIL PAN The following procedure applies to all of the oil 1. Install: delivery pipes. • Oil pan gasket 1. Check: • Oil pan • Ventilation chamber oil drain pipe •...

  • Page 266: Crankcase

    CRANKCASE EAS25540 CRANKCASE Separating the crankcase 8 Nm (0.8 m kg, 5.8 ft • • 8 Nm (0.8 m kg, 5.8 ft • • 20 Nm (2.0 m kg, 14 ft • • 12 Nm (1.2 m kg, 8.7 ft •...
  • Page 267 CRANKCASE Separating the crankcase 8 Nm (0.8 m kg, 5.8 ft • • 8 Nm (0.8 m kg, 5.8 ft • • 20 Nm (2.0 m kg, 14 ft • • 12 Nm (1.2 m kg, 8.7 ft • • 12 Nm (1.2 m kg, 8.7 ft •...

  • Page 268: Disassembling The Crankcase

    • M6 × 55 mm bolts: “15”, “22”–“27” 2. Apply: • M6 × 45 mm bolts: “17”–“19” • Sealant 24 23 22 (onto the crankcase mating surfaces) Yamaha bond No. 1215 90890-85505 ® (Three Bond No.1215 NOTE: Do not allow any sealant to come into contact with the oil gallery or crankshaft journal bear- 3.
  • Page 269 CRANKCASE ECA13980 NOTE: CAUTION: Tighten the bolts in the tightening sequence cast Before tightening the crankcase bolts, make on the crankcase. sure the transmission gears shift correctly when the shift drum assembly is turned by hand. 8. Tighten: • Crankcase bolts “11”–“28” 6.
  • Page 270 CONNECTING RODS AND PISTONS EAS24370 CONNECTING RODS AND PISTONS Removing the connecting rods and pistons 1st 15 Nm (1.5 m kg, 11 ft • • 2nd Specified angle 175˚-185˚ Order Job/Parts to remove Q’ty Remarks Separate. Crankcase Refer to “CRANKCASE” on page 5-55. Connecting rod cap Big end lower bearing Piston pin clip...

  • Page 271: Connecting Rods And Pistons

    CONNECTING RODS AND PISTONS EAS26030 REMOVING THE CONNECTING RODS AND PISTONS The following procedure applies to all of the con- necting rods and pistons. 1. Remove: • Connecting rod cap “1” NOTE: Identify the position of each connecting rod so that it can be reinstalled in its original place.

  • Page 272: Checking The Piston Rings

    CONNECTING RODS AND PISTONS d. If out of specification, replace the piston and NOTE: piston rings as a set. Measure cylinder bore “C” by taking side-to-side e. Calculate the piston-to-cylinder clearance and front-to-back measurements of the cylinder. with the following formula. Then, find the average of the measurements.

  • Page 273: Checking The Piston Pins

    CONNECTING RODS AND PISTONS NOTE: Piston pin outside diameter Level the piston ring into the cylinder with the 14.991–15.000 mm (0.5902– piston crown. 0.5906 in) Limit 14.971 mm (0.5894 in) a. 5 mm (0.20 in) 3. Measure: 3. Measure: • Piston ring end gap Out of specification →...

  • Page 274: Checking The Connecting Rods

    CONNECTING RODS AND PISTONS ET2C01013 CHECKING THE CONNECTING RODS 1. Measure: • Crankshaft-pin-to-big-end-bearing clearance Out of specification → Replace the big end bearings. Oil clearance (using plasti- ® gauge 0.037–0.061 mm (0.0015–0.0024 d. Assemble the connecting rod halves. NOTE: M MMM M MMM M MMM M MMM...

  • Page 275: Installing The Connecting Rods And Pistons

    CONNECTING RODS AND PISTONS For example, if the connecting rod P and the crankshaft web P numbers are 5 and 1 re- spectively, then the bearing size for P (connecting rod) - P (crankshaft) 5 - 1 = 4 (green) Bearing color code 1.Blue 2.Black 3.Brown 4.Green L LLL...
  • Page 276 CONNECTING RODS AND PISTONS Recommended lubricant Molybdenum disulfide oil 6. Lubricate: • Crankshaft pins • Big end bearings • Connecting rod inner surface (with the recommended lubricant) Recommended lubricant Engine oil 7. Install: • Big end bearings • Connecting rod and piston assembly •...
  • Page 277 CONNECTING RODS AND PISTONS M MMM M MMM M MMM M MMM M MMM NOTE: EW2C01007 On a hexagonal nut, note that the angle from WARNING one corner to another is 60°. Replace the connecting rod bolts and nuts with new ones. L LLL L LLL L LLL...

  • Page 278: Crankshaft

    CRANKSHAFT EAS25960 CRANKSHAFT Removing the crankshaft Order Job/Parts to remove Q’ty Remarks Separate. Crankcase Refer to “CRANKCASE” on page 5-55. Refer to “CONNECTING RODS AND PIS- Connecting rod caps TONS” on page 5-59. Crankshaft Crankshaft journal lower bearing Crankshaft journal upper bearing Oil nozzle For installation, reverse the removal proce- dure.

  • Page 279: Removing The Crankshaft Journal Bearings

    CRANKSHAFT 3. Measure: EAS26040 REMOVING THE CRANKSHAFT JOURNAL • Crankshaft-journal-to-crankshaft-journal- BEARINGS bearing clearance 1. Remove: Out of specification → Replace the crank- • Crankshaft journal lower bearings shaft journal bearings. (from the lower crankcase) • Crankshaft journal upper bearings Journal oil clearance (using plas- (from the upper crankcase) ®...
  • Page 280 CRANKSHAFT NOTE: • The numbers “A” stamped into the crankshaft web and the numbers “B” stamped into the lower crankcase are used to determine the re- placement crankshaft journal bearing sizes. • J –J refer to the bearings shown in the crank- shaft illustration.

  • Page 281: Installing The Crankshaft

    CRANKSHAFT EAS26200 INSTALLING THE CRANKSHAFT 1. Install: • Crankshaft journal upper bearings (into the upper crankcase) • Crankshaft journal lower bearings (into the lower crankcase) NOTE: • Align the projections “a” on the crankshaft jour- nal bearings “1” with the notches “b” in the crankcases.
  • Page 282 TRANSMISSION EAS26240 TRANSMISSION Removing the transmission, shift drum assembly, and shift forks 12 Nm (1.2 m kg, 8.7 ft • • 10 Nm (1.0 m kg, 7.2 ft • • 10 Nm (1.0 m kg, 7.2 ft • • Order Job/Parts to remove Q’ty Remarks...
  • Page 283 TRANSMISSION Removing the transmission, shift drum assembly, and shift forks 12 Nm (1.2 m kg, 8.7 ft • • 10 Nm (1.0 m kg, 7.2 ft • • 10 Nm (1.0 m kg, 7.2 ft • • Order Job/Parts to remove Q’ty Remarks Bearing...
  • Page 284 TRANSMISSION Disassembling the main axle assembly Order Job/Parts to remove Q’ty Remarks 2nd pinion gear Toothed lock washer Toothed lock washer retainer 6th pinion gear Collar Washer Circlip 3rd/4th pinion gear Circlip Washer 5th pinion gear Collar Bearing housing Bearing Main axle/1st pinion gear For assembly, reverse the disassembly pro- cedure.
  • Page 285 TRANSMISSION Disassembling the drive axle assembly Order Job/Parts to remove Q’ty Remarks Washer 1st wheel gear Collar 5th wheel gear Circlip Washer 3rd wheel gear Collar Toothed lock washer Toothed lock washer retainer 4th wheel gear Collar Washer Circlip 6th wheel gear Circlip Washer 5-74...
  • Page 286 TRANSMISSION Disassembling the drive axle assembly Order Job/Parts to remove Q’ty Remarks 2nd wheel gear Collar Bearing Drive axle For assembly, reverse the disassembly pro- cedure. 5-75...

  • Page 287: Transmission

    TRANSMISSION ET2C01014 REMOVING THE TRANSMISSION 1. Remove: • Main axle assembly “1” M MMM M MMM M MMM M MMM M MMM a. Remove the main axle assembly bearing housing bolts “2” 2. Check: • Shift fork guide bar Roll the shift fork guide bar on a flat surface. Bends →...

  • Page 288: Checking The Transmission

    TRANSMISSION • Shift drum bearing “2” • Transmission gear dogs Damage/pitting → Replace the shift drum as- Cracks/damage/rounded edges → Replace sembly. the defective gear(s). 4. Check: EAS26300 • Transmission gear engagement CHECKING THE TRANSMISSION (each pinion gear to its respective wheel 1.

  • Page 289: Installing The Transmission

    TRANSMISSION 2. Install: • Main axle assembly “1” NOTE: Stake the main axle assembly bearing housing bolts “2” at a cutout “a” in the main axle assem- bly bearing housing “3”. 2. Install: • Toothed lock washer retainer “1” • Toothed lock washer “2” NOTE: •...
  • Page 290 TRANSMISSION • Shift fork guide bar • Springs • Shift drum retainers “3” • Bearing • Oil seal • Circlip “4” • Drive axle assembly “5” Shift drum retainer bolt 10 Nm (1.0 m·kg, 7.2 ft·lb) ® LOCTITE NOTE: • Install shift fork-R into the groove “a” in the 5th wheel gear and shift fork-L into the groove “b”...

  • Page 291: Cooling System

    COOLING SYSTEM RADIATOR ...................... 6-1 CHECKING THE RADIATOR..............6-3 INSTALLING THE RADIATOR..............6-3 OIL COOLER....................6-4 CHECKING THE OIL COOLER ..............6-6 INSTALLING THE OIL COOLER .............. 6-6 THERMOSTAT ....................6-7 CHECKING THE THERMOSTAT.............. 6-8 INSTALLING THE THERMOSTAT............6-8 WATER PUMP....................6-9 CHECKING THE WATER PUMP ............

  • Page 292: Radiator

    RADIATOR EAS26380 RADIATOR Removing the radiator 13 Nm (1.3 m kg, 9.4 ft • • 5 Nm (0.5 m kg, 3.6 ft • • 10 Nm (1.0 m kg, 7.2 ft • • 5 Nm (0.5 m kg, 3.6 ft •...
  • Page 293 RADIATOR Removing the radiator 13 Nm (1.3 m kg, 9.4 ft • • 5 Nm (0.5 m kg, 3.6 ft • • 10 Nm (1.0 m kg, 7.2 ft • • 5 Nm (0.5 m kg, 3.6 ft • • 10 Nm (1.0 m kg, 7.2 ft •...

  • Page 294: Checking The Radiator

    RADIATOR EAS26390 CHECKING THE RADIATOR 1. Check: • Radiator fins Obstruction → Clean. Apply compressed air to the rear of the radia- tor. Damage → Repair or replace. NOTE: Straighten any flattened fins with a thin, flat-head b. Apply the specified pressure for ten seconds screwdriver.

  • Page 295: Oil Cooler

    OIL COOLER EAS26410 OIL COOLER Removing the oil cooler 63 Nm (6.3 m kg, 45 ft 10 Nm (1.0 m kg, 7.2 ft • • • • Order Job/Parts to remove Q’ty Remarks Drain. Engine oil Refer to “CHANGING THE ENGINE OIL” on page 3-11.
  • Page 296 OIL COOLER Removing the oil cooler 10 Nm (1.0 m kg, 7.2 ft 63 Nm (6.3 m kg, 45 ft • • • • Order Job/Parts to remove Q’ty Remarks O-ring For installation, reverse the removal proce- dure.

  • Page 297: Checking The Oil Cooler

    OIL COOLER • Crankcase EAS26420 CHECKING THE OIL COOLER (with the specified amount of the recom- 1. Check: mended engine oil) • Oil cooler Refer to “CHANGING THE ENGINE OIL” on Cracks/damage → Replace. page 3-11. 2. Check: 4. Check: •...

  • Page 298: Thermostat

    THERMOSTAT EAS26440 THERMOSTAT Removing the thermostat 12 Nm (1.2 m kg, 8.7 ft • • Order Job/Parts to remove Q’ty Remarks Air filter case Refer to “AIR FILTER CASE” on page 7-4. Drain. Coolant Refer to “CHANGING THE COOLANT” on page 3-19.

  • Page 299: Checking The Thermostat

    THERMOSTAT 2. Check: EAS26450 CHECKING THE THERMOSTAT • Thermostat cover 1. Check: Cracks/damage → Replace. • Thermostat Does not open at 71–85 °C (159.8–185.0 °F) EAS26480 → Replace. INSTALLING THE THERMOSTAT 1. Install: • Thermostat NOTE: Install the thermostat with its breather hole “a” facing up.

  • Page 300: Water Pump

    WATER PUMP EAS26500 WATER PUMP Removing the water pump 12 Nm (1.2 m kg, 8.7 ft • • 12 Nm (1.2 m kg, 8.7 ft • • 12 Nm (1.2 m kg, 8.7 ft • • Order Job/Parts to remove Q’ty Remarks It is not necessary to remove the water...

  • Page 301: Checking The Water Pump

    WATER PUMP EAS26540 CHECKING THE WATER PUMP 1. Check: • Water pump assembly Cracks/damage → Replace. 2. Check: • Water pump inlet hose • Water pump outlet hose • Water pump breather hose Cracks/damage/wear → Replace. EAS26590 INSTALLING THE WATER PUMP 1.
  • Page 302 WATER PUMP 6-11...

  • Page 303: Fuel System

    FUEL SYSTEM FUEL TANK..................... 7-1 REMOVING THE FUEL TANK ..............7-2 REMOVING THE FUEL PUMP ..............7-2 CHECKING THE FUEL PUMP BODY............7-2 CHECKING THE FUEL PUMP OPERATION..........7-2 INSTALLING THE FUEL PUMP..............7-2 INSTALLING THE FUEL TANK..............7-3 AIR FILTER CASE ..................7-4 REMOVING THE FUEL HOSE (PRIMARY INJECTOR FUEL RAIL TO SECONDARY INJECTOR FUEL RAIL)........

  • Page 304: Fuel Tank

    FUEL TANK EAS26620 FUEL TANK Removing the fuel tank and fuel pump 9 Nm (0.9 m kg, 6.5 ft • • 9 Nm (0.9 m kg, 6.5 ft • • 4 Nm (0.4 m kg, 2.9 ft • • 4 (6) 7 Nm (0.7 m kg, 5.1 ft •...

  • Page 305: Removing The Fuel Tank

    FUEL TANK EAS26630 EAS26640 REMOVING THE FUEL TANK REMOVING THE FUEL PUMP 1. Extract the fuel in the fuel tank through the 1. Remove: fuel tank cap with a pump. • Fuel pump 2. Remove: ECA14720 CAUTION: • Fuel hose (fuel tank to primary injector rail) •...

  • Page 306: Installing The Fuel Tank

    FUEL TANK ET2C01010 INSTALLING THE FUEL TANK 1. Connect: • Fuel tank breather hose (fuel tank to hose joint) “1” • Fuel tank overflow hose (fuel tank to hose joint) “2” • Fuel tank breather hose “3” • Fuel tank overflow hose “4” 2.

  • Page 307: Air Filter Case

    AIR FILTER CASE ET2C01003 AIR FILTER CASE Removing the air filter case and secondary injectors 1.5 Nm (0.15 m kg, 1.08 ft 5 Nm (0.5 m kg, 3.6 ft 2 Nm (0.2 m kg, 1.4 ft • • • • •...
  • Page 308 AIR FILTER CASE Removing the air filter case and secondary injectors 1.5 Nm (0.15 m kg, 1.08 ft 5 Nm (0.5 m kg, 3.6 ft 2 Nm (0.2 m kg, 1.4 ft • • • • • • 4 Nm (0.4 m kg, 2.9 ft •...

  • Page 309: Removing The Fuel Hose (Primary Injector Fuel Rail To Secondary Injector Fuel Rail)

    AIR FILTER CASE ET2C01005 EC2C01017 REMOVING THE FUEL HOSE (PRIMARY CAUTION: INJECTOR FUEL RAIL TO SECONDARY When installing the fuel hose, make sure that INJECTOR FUEL RAIL) it is securely connected, and that the fuel 1. Remove: hose connector cover on the fuel hose is in •...
  • Page 310 THROTTLE BODIES EAS26970 THROTTLE BODIES Removing the throttle body assembly 10 Nm (1.0 m kg, 7.2 ft • • Order Job/Parts to remove Q’ty Remarks Fuel tank Refer to “FUEL TANK” on page 7-1. Air filter case Refer to “AIR FILTER CASE” on page 7-4. Refer to “AIR INDUCTION SYSTEM”...

  • Page 311: Throttle Bodies

    THROTTLE BODIES Removing the throttle body assembly 10 Nm (1.0 m kg, 7.2 ft • • Order Job/Parts to remove Q’ty Remarks Throttle body joint clamp Heat protector Throttle body joint For installation, reverse the removal proce- dure.
  • Page 312 THROTTLE BODIES Removing the primary injectors 3.5 Nm (0.35 m kg, 2.53 ft • • 5 Nm (0.5 m kg, 3.6 ft • • 3.5 Nm (0.35 m kg, 2.53 ft • • 3.5 Nm (0.35 m kg, 2.53 ft •...

  • Page 313: Checking The Primary Injectors

    THROTTLE BODIES EAS26980 CHECKING THE PRIMARY INJECTORS Pressure gauge 1. Check: 90890-03153 • Injectors Pressure gauge Damage → Replace. YU-03153 Fuel pressure adapter 90890-03176 EAS26990 CHECKING THE THROTTLE BODIES YM-03176 1. Check: • Throttle bodies Cracks/damage → Replace the throttle bod- ies as a set.

  • Page 314: Adjusting The Throttle Position Sensor (For Throttle Cable Pulley)

    THROTTLE BODIES ET2C01008 ADJUSTING THE THROTTLE POSITION SENSOR (FOR THROTTLE CABLE PULLEY) 1. Check: • Throttle position sensor (for throttle cable pul- ley) Refer to “CHECKING THE THROTTLE PO- Lg/R SITION SENSOR (FOR THROTTLE CABLE PULLEY)” on page 8-107. 2. Adjust: •...
  • Page 315 THROTTLE BODIES Throttle body joint bolt 10 Nm (1.0 m·kg, 7.2 ft·lb) NOTE: Be sure to install the throttle body joints with the “L” mark onto the throttle body openings for cyl- inders #1 and #2 and the joints with the “R” mark onto the openings for cylinders #3 and #4.

  • Page 316: Air Induction System

    AIR INDUCTION SYSTEM EAS27040 AIR INDUCTION SYSTEM 7-13...
  • Page 317 AIR INDUCTION SYSTEM 1. Lower air filter case 2. Air induction system hose (air filter case to air cut-off valve) 3. Air cut-off valve 4. Air induction system hose (air cut-off valve to cylinder head cover) 5. Reed valve assembly 6.
  • Page 318 AIR INDUCTION SYSTEM Removing the air cut-off valve Order Job/Parts to remove Q’ty Remarks Fuel tank Refer to “FUEL TANK” on page 7-1. Air filter case Refer to “AIR FILTER CASE” on page 7-4. Air induction system cover Immobilizer unit coupler holder Air induction system solenoid coupler Disconnect.
  • Page 319 AIR INDUCTION SYSTEM Removing the reed valves 10 Nm (1.0 m kg, 7.2 ft • • 10 Nm (1.0 m kg, 7.2 ft • • Order Job/Parts to remove Q’ty Remarks Reed valve cover Reed valve assembly Reed valve plate For installation, reverse the removal proce- dure.

  • Page 320: Checking The Air Induction System

    AIR INDUCTION SYSTEM 2. Check: EAS27060 CHECKING THE AIR INDUCTION SYSTEM • Reed valve • Reed valve stopper Air injection • Reed valve seat The air induction system burns unburned ex- Cracks/damage → Replace the reed valve haust gases by injecting fresh air (secondary air) assembly.

  • Page 321: Electrical System

    ELECTRICAL SYSTEM IGNITION SYSTEM ..................8-1 CIRCUIT DIAGRAM .................. 8-1 ENGINE STOPPING DUE TO SIDESTAND OPERATION....... 8-3 TROUBLESHOOTING ................8-4 ELECTRIC STARTING SYSTEM ..............8-7 CIRCUIT DIAGRAM .................. 8-7 STARTING CIRCUIT CUT-OFF SYSTEM OPERATION ......8-9 TROUBLESHOOTING ................8-11 CHARGING SYSTEM..................8-13 CIRCUIT DIAGRAM ................
  • Page 322 ELECTRICAL COMPONENTS..............8-87 CHECKING THE SWITCHES ..............8-91 CHECKING THE BULBS AND BULB SOCKETS ........8-94 CHECKING THE FUSES ................ 8-95 CHECKING AND CHARGING THE BATTERY........8-96 CHECKING THE RELAYS ..............8-99 CHECKING THE TURN SIGNAL/HAZARD RELAY......8-100 CHECKING THE RELAY UNIT (DIODE) ..........8-101 CHECKING THE IGNITION COILS............8-102 CHECKING THE CRANKSHAFT POSITION SENSOR......8-103 CHECKING THE LEAN ANGLE SENSOR..........8-103...

  • Page 324: Ignition System

    IGNITION SYSTEM EAS27090 IGNITION SYSTEM EAS27110 CIRCUIT DIAGRAM...
  • Page 325 IGNITION SYSTEM 3. Main switch 4. Ignition fuse 6. Main fuse 7. Battery 11.Engine ground 14.Relay unit 17.Neutral switch 18.Sidestand switch 23.ECU (engine control unit) 24.Spark plug 25.Cylinder-#1 ignition coil 26.Cylinder-#2 ignition coil 27.Cylinder-#3 ignition coil 28.Cylinder-#4 ignition coil 41.Crankshaft position sensor 48.Lean angle sensor 66.Engine stop switch...

  • Page 326: Engine Stopping Due To Sidestand Operation

    IGNITION SYSTEM ET2C01023 ENGINE STOPPING DUE TO SIDESTAND OPERATION When the engine is running and the transmission is in gear, the engine will stop if the sidestand is moved down. This is because the electric current from the ignition coils does not flow to the ECU when both the neutral switch and sidestand switch are set to “OFF”, thereby preventing the spark plugs from producing a spark.

  • Page 327: Troubleshooting

    IGNITION SYSTEM EAS27150 TROUBLESHOOTING The ignition system fails to operate (no spark or intermittent spark). NOTE: • Before troubleshooting, remove the following part(s): 1. Rider seat 2. Fuel tank 3. Air filter case 4. Side cowlings 5. Bottom cowlings NG → 1.
  • Page 328 IGNITION SYSTEM NG → 8. Check the engine stop switch. Refer to “CHECKING THE Replace the right handlebar switch. SWITCHES” on page 8-91. OK ↓ NG → 9. Check the neutral switch. Refer to “CHECKING THE Replace the neutral switch. SWITCHES”...
  • Page 329 IGNITION SYSTEM...

  • Page 330: Electric Starting System

    ELECTRIC STARTING SYSTEM EAS27160 ELECTRIC STARTING SYSTEM EAS27170 CIRCUIT DIAGRAM R/B G/B Br/Y Br/Y L/B B/L Sb/W Br/B Br/B Sb/W (BLACK) (BLACK) B B2 R/G NEUTRAL SWITCH SUB SUB- WIRE-HARNESS3 WIRE HARNESS WIRE HARNESS WIRE HARNESS SUB-WIRE-HARNESS2 -WIRE-HARNESS Y/L Lg R/W R / W W W W (BLACK)
  • Page 331 ELECTRIC STARTING SYSTEM 3. Main switch 4. Ignition fuse 6. Main fuse 7. Battery 8. Starter relay 10.Starter motor 11.Engine ground 14.Relay unit 15.Starting circuit cut-off relay 17.Neutral switch 18.Sidestand switch 66.Engine stop switch 67.Start switch 74.Clutch switch...

  • Page 332: Starting Circuit Cut-Off System Operation

    ELECTRIC STARTING SYSTEM EAS27180 STARTING CIRCUIT CUT-OFF SYSTEM OPERATION If the engine stop switch is set to “ ” and the main switch is set to “ON” (both switches are closed), the starter motor can only operate if at least one of the following conditions is met: •...
  • Page 333 ELECTRIC STARTING SYSTEM a. WHEN THE TRANSMISSION IS IN NEUTRAL b. WHEN THE SIDESTAND IS UP AND THE CLUTCH LEVER IS PULLED TO THE HANDLEBAR 1. Battery 2. Main fuse 3. Main switch 4. Ignition fuse 5. Engine stop switch 6.

  • Page 334: Troubleshooting

    ELECTRIC STARTING SYSTEM EAS27190 TROUBLESHOOTING The starter motor fails to turn. NOTE: • Before troubleshooting, remove the following part(s): 1. Rider seat 2. Fuel tank 3. Air filter case 4. Side cowlings 5. Thermostat NG → 1. Check the fuses. (Main and ignition) Replace the fuse(s).
  • Page 335 ELECTRIC STARTING SYSTEM NG → 8. Check the neutral switch. Refer to “CHECKING THE Replace the neutral switch. SWITCHES” on page 8-91. OK ↓ NG → 9. Check the sidestand switch. Refer to “CHECKING THE Replace the sidestand switch. SWITCHES” on page 8-91. OK ↓...
  • Page 336 CHARGING SYSTEM EAS27200 CHARGING SYSTEM EAS27210 CIRCUIT DIAGRAM B B2 R/G Y/L Lg R/W R / W W W W (BLACK) W W W R/W L/W Br/R Br/R L/W3 Br/L Br/L Br/L Br/R Br/L L/W2 G/Y L/W2 R/W BB3 BB4 BB2 BB1 B Br (BLUE)

  • Page 337: Charging System

    CHARGING SYSTEM 1. AC magneto 2. Rectifier/regulator 6. Main fuse 7. Battery 11.Engine ground 8-14...

  • Page 338: Circuit Diagram

    CHARGING SYSTEM EAS27230 TROUBLESHOOTING The battery is not being charged. NOTE: • Before troubleshooting, remove the following part(s): 1. Rider seat 2. Fuel tank 3. Bottom cowlings NG → 1. Check the fuse. (Main) Replace the fuse. Refer to “CHECKING THE FUS- ES”...
  • Page 339 CHARGING SYSTEM 8-16...

  • Page 340: Lighting System

    LIGHTING SYSTEM EAS27240 LIGHTING SYSTEM EAS27250 CIRCUIT DIAGRAM 8-17...
  • Page 341 LIGHTING SYSTEM 3. Main switch 6. Main fuse 7. Battery 11.Engine ground 23.ECU (engine control unit) 59.High beam indicator light 62.Meter light 71.Pass switch 72.Dimmer switch 81.Headlight (low beam) 82.Headlight (high beam) 83.Auxiliary light 84.License plate light 86.Tail/brake light 87.Headlight relay (on/off) 88.Headlight relay (dimmer) 90.Taillight fuse 92.Headlight fuse...

  • Page 342: Troubleshooting

    LIGHTING SYSTEM EAS27260 TROUBLESHOOTING Any of the following fail to light: headlight (high beam), headlight (low beam), high beam indicator light, taillight, license plate light, auxiliary light or meter light. NOTE: • Before troubleshooting, remove the following part(s): 1. Rider seat 2.
  • Page 343 LIGHTING SYSTEM NG → 8. Check the headlight relay (dimmer). Refer to “CHECKING THE RE- Replace the headlight relay (dimmer). LAYS” on page 8-99. OK ↓ NG → 9. Check the entire lighting system’s wiring. Properly connect or repair the lighting sys- Refer to “CIRCUIT DIAGRAM”...

  • Page 344: Signaling System

    SIGNALING SYSTEM EAS27270 SIGNALING SYSTEM EAS27280 CIRCUIT DIAGRAM 8-21...
  • Page 345 SIGNALING SYSTEM 3. Main switch 4. Ignition fuse 6. Main fuse 7. Battery 11.Engine ground 14.Relay unit 17.Neutral switch 20.Fuel sender 23.ECU (engine control unit) 41.Crankshaft position sensor 43.Coolant temperature sensor 46.Cylinder identification sensor 47.Speed sensor 51.Fuel level warning light 52.Oil level warning light 53.Neutral indicator light 54.Tachometer...

  • Page 346: Troubleshooting

    SIGNALING SYSTEM EAS27290 TROUBLESHOOTING • Any of the following fail to light: turn signal light, brake light or indicator light. • The horn fails to sound. NOTE: • Before troubleshooting, remove the following part(s): 1. Rider seat 2. Fuel tank 3.
  • Page 347 SIGNALING SYSTEM NG → 3. Check the entire signaling system’s wiring. Properly connect or repair the signaling Refer to “CIRCUIT DIAGRAM” on system’s wiring. page 8-21. OK ↓ This circuit is OK. The brake light fails to come on. NG → 1.
  • Page 348 SIGNALING SYSTEM NG → 5. Check the entire signaling system’s wiring. Properly connect or repair the signaling Refer to “CIRCUIT DIAGRAM” on system’s wiring. page 8-21. OK ↓ This circuit is OK. The neutral indicator light fails to come. NG → 1.
  • Page 349 SIGNALING SYSTEM NG → 2. Check the entire signaling system’s wiring. Properly connect or repair the signaling Refer to “CIRCUIT DIAGRAM” on system’s wiring. page 8-21. OK ↓ This circuit is OK. The coolant temperature warning light fails to come. NG →...
  • Page 350 SIGNALING SYSTEM NG → 2. Check the entire signaling system’s wiring. Properly connect or repair the signaling Refer to “CIRCUIT DIAGRAM” on system’s wiring. page 8-21. OK ↓ This circuit is OK. 8-27...
  • Page 351 SIGNALING SYSTEM 8-28...

  • Page 352: Cooling System

    COOLING SYSTEM EAS27300 COOLING SYSTEM EAS27310 CIRCUIT DIAGRAM 8-29...
  • Page 353 COOLING SYSTEM 3. Main switch 4. Ignition fuse 6. Main fuse 7. Battery 11.Engine ground 23.ECU (engine control unit) 43.Coolant temperature sensor 93.Radiator fan motor relay 94.Right radiator fan motor fuse 95.Left radiator fan motor fuse 96.Right radiator fan motor 97.Left radiator fan motor 8-30...

  • Page 354: Troubleshooting

    COOLING SYSTEM EAS27320 TROUBLESHOOTING NOTE: • Before troubleshooting, remove the following part(s): 1. Rider seat 2. Fuel tank 3. Side cowlings NG → 1. Check the fuses. (Main, ignition and radiator fan mo- tor) Replace the fuse(s). Refer to “CHECKING THE FUS- ES”...
  • Page 355 COOLING SYSTEM 8-32...

  • Page 356: Fuel Injection System

    FUEL INJECTION SYSTEM EAS27330 FUEL INJECTION SYSTEM EAS27340 CIRCUIT DIAGRAM 8-33...
  • Page 357 FUEL INJECTION SYSTEM 3. Main switch 4. Ignition fuse 5. Backup fuse (odometer, clock and immobilizer system) 6. Main fuse 7. Battery 9. Fuel injection system fuse 11.Engine ground 13.ETV fuse 14.Relay unit 16.Fuel pump relay 17.Neutral switch 18.Sidestand switch 19.Fuel pump 21.Throttle position sensor (for throttle cable pulley)

  • Page 358: Ecu Self-Diagnostic Function

    FUEL INJECTION SYSTEM EAS27350 ECU SELF-DIAGNOSTIC FUNCTION The ECU is equipped with a self-diagnostic function in order to ensure that the fuel injection system is operating normally. If this function detects a malfunction in the system, it immediately operates the en- gine under substitute characteristics and illuminates the engine trouble warning light to alert the rider that a malfunction has occurred in the system.

  • Page 359: Self-Diagnostic Function Table

    FUEL INJECTION SYSTEM a. Main switch “OFF” d. Engine trouble warning light on for 1.4 seconds b. Main switch “ON” c. Engine trouble warning light off EAS27380 SELF-DIAGNOSTIC FUNCTION TABLE If the ECU detects an abnormal signal from a sensor while the vehicle is being driven, the ECU illumi- nates the engine trouble warning light and provides the engine with alternate operating instructions that are appropriate for the type of malfunction.
  • Page 360 FUEL INJECTION SYSTEM Able/un- Fault Able/un- Item Symptom able to code No. able to start drive EXUP servo motor EXUP servo motor is stuck. Able Able (stuck) Sidestand switch Open circuit is detected in the in- (open circuit in the put line from the sidestand switch Unable Unable...
  • Page 361 FUEL INJECTION SYSTEM Able/un- Fault Able/un- Item Symptom able to code No. able to start drive Able Able (depending (depending Primary injector Primary injector: on the on the (open circuit) open circuit detected. number of number of faulty cylin- faulty cylin- ders) ders) Able...

  • Page 362: Troubleshooting Method

    FUEL INJECTION SYSTEM Able/un- Fault Able/un- Item Symptom able to code No. able to start drive ECU internal malfunc- No signals are received from the Er-2 tion Unable Unable ECU within the specified duration. (output signal error) ECU internal malfunc- Data from the ECU cannot be re- Er-3 tion...

  • Page 363: Diagnostic Mode

    FUEL INJECTION SYSTEM EAS27420 DIAGNOSTIC MODE Setting the diagnostic mode 1. Turn the main switch to “OFF”. 2. Disconnect the wire harness coupler from the fuel pump. 3. Press and hold the “SELECT” and “RESET” buttons, turn the main switch to “ON”, and continue to press the buttons for 8 seconds or more.
  • Page 364 FUEL INJECTION SYSTEM Fault code table Fault Diagnostic code Symptom Probable cause of malfunction code No. No normal signals are re- • Open or short circuit in sub-wire-harness 1. ceived from the cylinder • Open or short circuit in wire harness. identification sensor when •...
  • Page 365 FUEL INJECTION SYSTEM Fault Diagnostic code Symptom Probable cause of malfunction code No. • Open or short circuit in wire harness. Air temperature sensor: • Defective air temperature sensor. open or short circuit detect- • Malfunction in ECU. • Improperly installed air temperature sensor. •...
  • Page 366 FUEL INJECTION SYSTEM Fault Diagnostic code Symptom Probable cause of malfunction code No. Power supply to the injec- • Open or short circuit in wire harness. tors and the fuel pump is • Malfunction in ECU. not normal. An error is detected while •...
  • Page 367 FUEL INJECTION SYSTEM Sensor operation table Diag- nostic Item Meter display Checking method code Throttle position sensor (for throttle valves) signal 1 • Fully closed position 12–21 Check with throttle valves fully closed. • Fully opened position 97–106 Check with throttle valves fully opened.
  • Page 368 FUEL INJECTION SYSTEM Diag- nostic Item Meter display Checking method code Throttle position sensor (for throttle cable pulley) signal • Fully closed position 12–22 Check with throttle grip fully closed. • Fully opened position 97–107 Check with throttle grip fully opened.
  • Page 369 FUEL INJECTION SYSTEM Diag- nostic Item Meter display Checking method code Malfunction history code erasure • No history — • History exists • Displays the total number of To erase the history, set the malfunctions, including the engine stop switch from current malfunction, that “...
  • Page 370 FUEL INJECTION SYSTEM Diag- nostic Item Actuation Checking method code Actuates the cylinder-#4 igni- tion coil five times at one- Check the spark five times. Cylinder-#4 ignition coil second intervals. • Connect an ignition Illuminates the engine trou- checker. ble warning light. Actuates the primary injector #1 five times at one-second Check the operating sound...

  • Page 371: Troubleshooting Details

    FUEL INJECTION SYSTEM Diag- nostic Item Actuation Checking method code Actuates the air induction system solenoid five times at Check the operating sound Air induction system sole- one-second intervals. of the air induction system noid Illuminates the engine trou- solenoid five times. ble warning light.
  • Page 372 FUEL INJECTION SYSTEM Fault code No. Symptom No normal signals are received from the cylinder identifi- cation sensor when the engine is started or while the ve- hicle is being driven. Diagnostic code No. — — Order Item/components and probable Check or maintenance job Reinstatement cause...
  • Page 373 FUEL INJECTION SYSTEM Fault code No. Symptom No normal signals are received from the crankshaft posi- tion sensor. Diagnostic code No. — — Order Item/components and probable Check or maintenance job Reinstatement cause method Installed condition of crankshaft posi- Check for looseness or pinching. Cranking the tion sensor.
  • Page 374 FUEL INJECTION SYSTEM Fault code No. Symptom Intake air pressure sensor: open or short circuit detected. Diagnostic code No. Intake air pressure sensor Order Item/components and probable Check or maintenance job Reinstatement cause method Connections • Check the couplers for any pins Reinstated au- •...
  • Page 375 FUEL INJECTION SYSTEM Fault code No. Symptom Throttle position sensor (for throttle valves): open or short circuit detected. Diagnostic code No. Throttle position sensor (for throttle valves) signal 1 Throttle position sensor (for throttle valves) signal 2 Order Item/components and probable Check or maintenance job Reinstatement cause...
  • Page 376 FUEL INJECTION SYSTEM Fault code No. Symptom EXUP servo motor circuit: open or short circuit detected. Diagnostic code No. EXUP servo motor Order Item/components and probable Check or maintenance job Reinstatement cause method Connections • Check the couplers for any pins Reinstated au- •...
  • Page 377 FUEL INJECTION SYSTEM Fault code No. Symptom Open circuit is detected in the input lead from the side- stand switch to the ECU. Diagnostic code No. Sidestand switch Order Item/components and probable Check or maintenance job Reinstatement cause method Connections •...
  • Page 378 FUEL INJECTION SYSTEM Fault code No. Symptom Coolant temperature sensor: open or short circuit detect- Diagnostic code No. Coolant temperature sensor Order Item/components and probable Check or maintenance job Reinstatement cause method Connections • Check the couplers for any pins Reinstated au- •...
  • Page 379 FUEL INJECTION SYSTEM Fault code No. Symptom Atmospheric pressure sensor: open or short circuit de- tected. Diagnostic code No. Atmospheric pressure sensor Order Item/components and probable Check or maintenance job Reinstatement cause method Connections • Check the couplers for any pins Reinstated au- •...
  • Page 380 FUEL INJECTION SYSTEM Fault code No. Symptom No normal signal is received from the O sensor. Diagnostic code No. — — Order Item/components and probable Check or maintenance job Reinstatement cause method Installed state of O sensor. Check for looseness or pinching. Execute the di- agnostic mode Connections •...
  • Page 381 FUEL INJECTION SYSTEM Fault code No. Symptom Open circuit detected in the primary lead of the cylinder- #1 ignition coil. Diagnostic code No. Cylinder-#1 ignition coil Order Item/components and probable Check or maintenance job Reinstatement cause method Connections • Check the couplers for any pins Cranking the •...
  • Page 382 FUEL INJECTION SYSTEM Fault code No. Symptom Open circuit detected in the primary lead of the cylinder- #3 ignition coil. Diagnostic code No. Cylinder-#3 ignition coil Order Item/components and probable Check or maintenance job Reinstatement cause method Connections • Check the couplers for any pins Cranking the •...
  • Page 383 FUEL INJECTION SYSTEM Fault code No. Symptom Open circuit detected in the primary lead of the cylinder- #4 ignition coil. Diagnostic code No. Cylinder-#4 ignition coil Order Item/components and probable Check or maintenance job Reinstatement cause method Connections • Check the couplers for any pins Cranking the •...
  • Page 384 FUEL INJECTION SYSTEM Fault code No. Symptom Open circuit detected in a primary injector. Diagnostic code No. Primary injector #1 Primary injector #2 Primary injector #3 Primary injector #4 Order Item/components and probable Check or maintenance job Reinstatement cause method Connections •...
  • Page 385 FUEL INJECTION SYSTEM Fault code No. Symptom Open circuit detected in a secondary injector. Diagnostic code No. Secondary injector #1 Secondary injector #2 Secondary injector #3 Secondary injector #4 Order Item/components and probable Check or maintenance job Reinstatement cause method Connections •...
  • Page 386 FUEL INJECTION SYSTEM Fault code No. Symptom Lean angle sensor: open or short circuit detected. Diagnostic code No. Lean angle sensor Order Item/components and probable Check or maintenance job Reinstatement cause method Connections • Check the couplers for any pins Reinstated au- •...
  • Page 387 FUEL INJECTION SYSTEM Fault code No. Symptom A. No normal signals are received from the speed sensor. B. Open circuit is detected in the neutral switch. Diagnostic code No. Speed sensor Neutral switch Order Item/components and probable Check or maintenance job Reinstatement cause method...
  • Page 388 FUEL INJECTION SYSTEM Fault code No. Symptom A. No normal signals are received from the speed sensor. B. Open circuit is detected in the neutral switch. Diagnostic code No. Speed sensor Neutral switch Order Item/components and probable Check or maintenance job Reinstatement cause method...
  • Page 389 FUEL INJECTION SYSTEM Fault code No. Symptom Power supply to the injectors and fuel pump is not nor- mal. Diagnostic code No. Fuel system voltage (battery voltage) Order Item/components and probable Check or maintenance job Reinstatement cause method Connections • Check the couplers for any pins Turning the •...
  • Page 390 FUEL INJECTION SYSTEM Fault code No. Symptom An error is detected while reading or writing on EEPROM (CO adjustment value). Diagnostic code No. EEPROM fault cylinder No. Order Item/components and probable Check or maintenance job Reinstatement cause method Malfunction in ECU. •...
  • Page 391 FUEL INJECTION SYSTEM Fault code No. Symptom Throttle position sensor (for throttle cable pulley): open or short circuit detected. Throttle position sensor (for throttle cable pulley): coupler connection is loose. Diagnostic code No. Throttle position sensor (for throttle cable pulley) signal 1 Throttle position sensor (for throttle cable pulley) signal 2 Order Item/components and probable Check or maintenance job...
  • Page 392 FUEL INJECTION SYSTEM Fault code No. Symptom Throttle servo motor: open or short circuit detected. Defective throttle servo motor. Malfunction in ECU (servo motor driving system). Diagnostic code No. Throttle position sensor (for throttle valves) signal 1 Throttle position sensor (for throttle valves) signal 2 Order Item/components and probable Check or maintenance job Reinstatement...
  • Page 393 FUEL INJECTION SYSTEM Fault code No. Er-2 Symptom No signals are received from the ECU within the specified duration. Diagnostic code No. — — Order Item/components and probable Check or maintenance job Reinstatement cause method Connections • Check the couplers for any pins Turning the •...
  • Page 394 FUEL INJECTION SYSTEM Fault code No. Er-4 Symptom Non-registered data has been received from the meter. Diagnostic code No. — — Order Item/components and probable Check or maintenance job Reinstatement cause method Connections • Check the couplers for any pins Turning the •...
  • Page 395 FUEL INJECTION SYSTEM 8-72...

  • Page 396: Fuel Pump System

    FUEL PUMP SYSTEM EAS27550 FUEL PUMP SYSTEM EAS27560 CIRCUIT DIAGRAM 8-73...
  • Page 397 FUEL PUMP SYSTEM 3. Main switch 4. Ignition fuse 6. Main fuse 7. Battery 9. Fuel injection system fuse 11.Engine ground 14.Relay unit 16.Fuel pump relay 19.Fuel pump 23.ECU (engine control unit) 66.Engine stop switch 8-74...

  • Page 398: Troubleshooting

    FUEL PUMP SYSTEM EAS27570 TROUBLESHOOTING If the fuel pump fails to operate. NOTE: • Before troubleshooting, remove the following part(s): 1. Rider seat 2. Fuel tank 3. Side cowlings NG → 1. Check the fuses. (Main, ignition and fuel injection system) Replace the fuse(s).
  • Page 399 FUEL PUMP SYSTEM 8-76...

  • Page 400: Immobilizer System

    IMMOBILIZER SYSTEM EAS27640 IMMOBILIZER SYSTEM EAS27650 CIRCUIT DIAGRAM 8-77...
  • Page 401 IMMOBILIZER SYSTEM 3. Main switch 4. Ignition fuse 5. Backup fuse (odometer, clock and immobilizer system) 6. Main fuse 7. Battery 11.Engine ground 12.Immobilizer unit 23.ECU (engine control unit) 50.Immobilizer system indicator light 56.Multi-function meter 8-78...

  • Page 402: General Information

    IMMOBILIZER SYSTEM EAS27670 GENERAL INFORMATION This vehicle is equipped with an immobilizer system to help prevent theft by re-registering codes in the standard keys. This system consists of the following: • a code re-registering key (with a red bow) • two standard keys (with a black bow) that can be re-registered with new codes •...
  • Page 403 IMMOBILIZER SYSTEM Parts to be replaced Main switch/immo- Key registration re- Accesso- bilizer unit Standard quirement ry lock* Main Immobiliz- and key switch er unit √ Standard key is lost New standard key All keys have been Code re-registering √ √...
  • Page 404 IMMOBILIZER SYSTEM Standby mode a. Main switch “ON” d. LED off b. Main switch “OFF” e. Standby mode on c. LED on f. Standby mode off Standard key registration: Standard key registration is required when a standard key is lost and needs to be replaced, or when the code re-registering key is re-registered after the immobilizer unit or ECU are replaced.
  • Page 405 IMMOBILIZER SYSTEM Standard key registration a. Main switch “ON” g. First standard key b. Main switch “OFF” h. Second standard key c. LED on i. Registration mode d. LED off A. Registration of the second standard key is e. Less than 5.0 s complete.

  • Page 406: Troubleshooting

    IMMOBILIZER SYSTEM EAS27700 TROUBLESHOOTING When the main switch is turned to “ON”, the immobilizer system indicator light does not come on nor flashes. NG → 1. Check the fuses. (Main, ignition, and backup) Replace the fuse(s). Refer to “CHECKING THE FUS- ES”...
  • Page 407 IMMOBILIZER SYSTEM Fault Part Symptom Cause Action code IMMOBILIZER Codes between the 1. Signal received from 1. Place the immo- UNIT key and immobilizer other transponder bilizer unit at unit do not match. (failed to recognize least 50 mm code after ten con- away from the secutive attempts).
  • Page 408 IMMOBILIZER SYSTEM a. Light on b. Light off 8-85...
  • Page 409 IMMOBILIZER SYSTEM 8-86...

  • Page 410: Electrical Components

    ELECTRICAL COMPONENTS EAS27970 ELECTRICAL COMPONENTS 8-87...
  • Page 411 ELECTRICAL COMPONENTS 1. Main switch 2. Immobilizer unit 3. Front brake light switch 4. Clutch switch 5. Battery 6. Fuse box (backup, ETV) 7. Main fuse 8. Fuel injection system fuse 9. Starter relay 10. Neutral switch 11. EXUP servo motor 12.
  • Page 412 ELECTRICAL COMPONENTS 8-89...
  • Page 413 ELECTRICAL COMPONENTS 1. Air temperature sensor 2. Atmospheric pressure sensor 3. Coolant temperature sensor 4. Fuel pump 5. ECU (engine control unit) 6. Lean angle sensor 7. Relay unit 8. Turn signal/hazard relay 9. Crankshaft position sensor 10. Intake air pressure sensor 11.

  • Page 414: Checking The Switches

    ELECTRICAL COMPONENTS EAS27980 CHECKING THE SWITCHES L/Y2 R Br/L Br/R Br/R Br/L R/Y R/B Ch Br/W Dg L/W B (BLUE) R/Y W/Y Y R/Y Br/W Br B Br/W (BROWN) (BLUE) 8-91...
  • Page 415 ELECTRICAL COMPONENTS 1. Clutch switch 2. Main switch 3. Hazard switch 4. Pass switch 5. Dimmer switch 6. Horn switch 7. Turn signal switch 8. Sidestand switch 9. Front brake light switch 10. Engine stop switch 11. Start switch 12. Neutral switch 13.
  • Page 416 ELECTRICAL COMPONENTS Check each switch for continuity with the pocket tester. If the continuity reading is incorrect, check the wiring connections and if necessary, replace the switch. ECA14370 CAUTION: Never insert the tester probes into the coupler terminal slots “a”. Always insert the probes from the opposite end of the coupler, taking care not to loosen or damage the leads.

  • Page 417: Checking The Bulbs And Bulb Sockets

    ELECTRICAL COMPONENTS 1. Remove: EAS27990 CHECKING THE BULBS AND BULB • Bulb SOCKETS EW2C01001 WARNING NOTE: Do not check any of the lights that use LEDs. Since headlight bulbs get extremely hot, keep flammable products and your hands Check each bulb and bulb socket for damage or away from them until they have cooled wear, proper connections, and also for continuity down.

  • Page 418: Checking The Fuses

    ELECTRICAL COMPONENTS M MMM M MMM M MMM M MMM M MMM a. Connect the pocket tester to the fuse and check the continuity. NOTE: Set the pocket tester selector to “Ω × 1”. Pocket tester 90890-03112 Analog pocket tester YU-03112-C Checking the condition of the bulb sockets b.

  • Page 419: Checking And Charging The Battery

    ELECTRICAL COMPONENTS cal system, cause the lighting and ignition electrolyte level will drop considerably. systems to malfunction and could possibly Therefore, take special care when charging cause a fire. the battery. L LLL L LLL L LLL L LLL L LLL NOTE: 4.
  • Page 420 ELECTRICAL COMPONENTS b. Check the charge of the battery, as shown in • Do not use a high-rate battery charger the charts and the following example. since it forces a high-amperage current into the battery quickly and can cause bat- Example tery overheating and battery plate damage.
  • Page 421 ELECTRICAL COMPONENTS M MMM M MMM M MMM M MMM M MMM NOTE: Charging method using a variable-current Voltage should be measured 30 minutes after (voltage) charger the engine is stopped. a. Measure the open-circuit voltage prior to charging. b. Connect a charger and ammeter to the bat- tery and start charging.

  • Page 422: Checking The Relays

    ELECTRICAL COMPONENTS Relay unit (starting circuit cut-off relay) Recommended lubricant Dielectric grease 10.Install: • Fuel tank bracket • Rider seat Refer to “GENERAL CHASSIS” on page 4-1. EAS28040 CHECKING THE RELAYS Check each switch for continuity with the pocket 1. Positive battery terminal tester.

  • Page 423: Checking The Turn Signal/Hazard Relay

    ELECTRICAL COMPONENTS ET2C01021 3. Positive tester probe CHECKING THE TURN SIGNAL/HAZARD 4. Negative tester probe RELAY 1. Check: Result • Turn signal/hazard relay input voltage Continuity Out of specification → The wiring circuit from (between “3” and “4”) the main switch to the turn signal/hazard re- lay coupler is faulty and must be repaired.

  • Page 424: Checking The Relay Unit (Diode)

    ELECTRICAL COMPONENTS Pocket tester Continuity Positive tester probe → sky blue 90890-03112 Analog pocket tester “1” Negative tester probe → YU-03112-C black/yellow “2” No continuity • Positive tester probe → Positive tester probe → brown/white “1” black/yellow “2” • Negative tester probe → Negative tester probe →...

  • Page 425: Checking The Ignition Coils

    ELECTRICAL COMPONENTS c. Check the relay unit (diode) for continuity. Pocket tester d. Check the relay unit (diode) for no continuity. 90890-03112 L LLL L LLL L LLL L LLL L LLL Analog pocket tester YU-03112-C EAS28100 CHECKING THE IGNITION COILS The following procedure applies to all of the igni- •...

  • Page 426: Checking The Crankshaft Position Sensor

    ELECTRICAL COMPONENTS d. Crank the engine by pushing the start switch Lean angle sensor output voltage “ ” and gradually increase the spark gap un- Less than 65°: 0.4–1.4 V til a misfire occurs. More than 65°: 3.7–4.4 V L LLL L LLL L LLL L LLL...

  • Page 427: Checking The Rectifier/Regulator

    ELECTRICAL COMPONENTS • Positive tester probe → white “1” • Negative tester probe → white “2” • Positive tester probe → white “1” • Negative tester probe → white “3” • Positive tester probe → c. Start the engine and let it run at approximate- white “2”...

  • Page 428: Checking The Oil Level Switch

    ELECTRICAL COMPONENTS M MMM M MMM M MMM M MMM M MMM a. Connect a battery (12 V) to the horn. b. Turn the adjusting screw in direction “a” or “b” until the horn sound is obtained. b. Measure the oil level switch resistance. L LLL L LLL L LLL...

  • Page 429: Checking The Speed Sensor

    ELECTRICAL COMPONENTS EAS28240 CHECKING THE SPEED SENSOR 1. Check: • Speed sensor output voltage Out of specification → Replace. Output voltage reading cycle 0.6 V to 4.8 V to 0.6 V to 4.8 V M MMM M MMM M MMM M MMM M MMM a.

  • Page 430: Checking The Throttle Position Sensor

    ELECTRICAL COMPONENTS Pocket tester 90890-03112 Analog pocket tester YU-03112-C • Positive tester probe → blue “1” • Negative tester probe → black/blue “2” b. Measure the throttle position sensor (for b. Immerse the coolant temperature sensor “1” throttle valves) maximum resistance. in a container filled with coolant “2”.

  • Page 431: Checking The Fuel Pump

    ELECTRICAL COMPONENTS • Fuel sender coupler Pocket tester (from the wire harness) 90890-03112 2. Remove: Analog pocket tester • Fuel tank YU-03112-C 3. Check: • Fuel pump operation • Positive tester probe → Faulty/rough movement → Replace. blue “1” M MMM M MMM M MMM M MMM...

  • Page 432: Checking The Atmospheric Pressure Sensor

    ELECTRICAL COMPONENTS b. Connect the pocket tester (Ω × 1) to the air in- duction system solenoid terminal as shown. Pocket tester P B/L L 90890-03112 Analog pocket tester YU-03112-C • Positive tester probe → brown/red “1” • Negative tester probe → b.

  • Page 433: Checking The Intake Air Pressure Sensor

    ELECTRICAL COMPONENTS b. Turn the main switch to “ON”. • Never subject the air temperature sensor to c. Rotate the crankshaft. strong shocks. If the air temperature sen- d. Measure the voltage of white/black and sor is dropped, replace it. black/blue.
  • Page 434 ELECTRICAL COMPONENTS 8-111...

  • Page 435: Troubleshooting

    TROUBLESHOOTING TROUBLESHOOTING..................9-1 GENERAL INFORMATION ............... 9-1 STARTING FAILURES................9-1 INCORRECT ENGINE IDLING SPEED ............ 9-1 POOR MEDIUM-AND-HIGH-SPEED PERFORMANCE ......9-2 FAULTY GEAR SHIFTING................ 9-2 SHIFT PEDAL DOES NOT MOVE ............9-2 JUMPS OUT OF GEAR................9-2 FAULTY CLUTCH ..................9-2 OVERHEATING ..................

  • Page 436: Troubleshooting

    TROUBLESHOOTING Electrical system EAS28450 TROUBLESHOOTING 1. Battery • Discharged battery EAS28460 • Faulty battery GENERAL INFORMATION 2. Fuse(s) NOTE: • Blown, damaged or incorrect fuse The following guide for troubleshooting does not • Improperly installed fuse cover all the possible causes of trouble. It should 3.

  • Page 437: Poor Medium-And-High-Speed Performance

    TROUBLESHOOTING Electrical system EAS28550 JUMPS OUT OF GEAR 1. Battery • Discharged battery Shift shaft • Faulty battery • Incorrect shift pedal position 2. Spark plug(s) • Improperly returned stopper lever • Incorrect spark plug gap • Incorrect spark plug heat range Shift forks •...

  • Page 438: Overcooling

    TROUBLESHOOTING 2. Engine oil • Worn brake disc • Incorrect oil level • Air in hydraulic brake system • Incorrect oil viscosity • Leaking brake fluid • Inferior oil quality • Faulty brake caliper kit • Faulty brake caliper seal Cooling system •...

  • Page 439: Faulty Lighting Or Signaling System

    TROUBLESHOOTING Rear shock absorber assembly Turn signal does not come on • Faulty rear shock absorber spring • Faulty turn signal switch • Leaking oil or gas • Faulty turn signal/hazard relay • Burnt-out turn signal bulb Tire(s) • Incorrect connection •...

  • Page 440: Wiring Diagram

    EAS28740 54. Tachometer Yellow WIRING DIAGRAM 55. Shift timing indicator light Black/Green 56. Multi-function meter YZF-R6(V) 2006 Black/Blue 57. Engine trouble warning light Black/Red 1. AC magneto Black/White 58. Coolant temperature warning 2. Rectifier/regulator Black/Yellow light 3. Main switch Br/B Brown/Black 59.
  • Page 442 YAMAHA MOTOR CO., LTD. 2500 SHINGAI IWATA SHIZUOKA JAPAN...
  • Page 443 YZF-R6(V) 2006 YZF-R6(V) 2006 YZF-R6(V) 2006 SCHEMA ELETTRICO DIAGRAMA ELÉCTRICO DE LA WIRING DIAGRAM SCHÉMA DE CÂBLAGE SCHALTPLAN YZF-R6(V) 2006 YZF-R6(V) 2006 Gy/R Gy/R R/B G/B Br/W R/G Y/L G/W B/W Br/Y Br/Y Br/W L/B B/L Gy/G Br/R W/B Br/R...
  • Page 444 YZF-R6(V) 2006 YZF-R6(V) 2006 YZF-R6(V) 2006 SCHEMA ELETTRICO DIAGRAMA ELÉCTRICO DE LA WIRING DIAGRAM SCHÉMA DE CÂBLAGE SCHALTPLAN YZF-R6(V) 2006 YZF-R6(V) 2006 (BLACK) (BLACK) NEUTRAL SWITCH SUB HEADLIGHT SUB- SUB-WIRE-HARNESS3 WIRE HARNESS WIRE HARNESS WIRE HARNESS SUB-WIRE-HARNESS2 WIRE HARNESS SUB-WIRE-HARNESS1...

Table of Contents