Enhancement Menu - Hitachi KP-D5000 Operation Manual

Enhancement menu [ENHANCE]
Enhancement menu is used to modify the picture quality of
camera output.
1) Press the Set button for longer than 2 seconds to display the
Main menu.
2) Use the Up and Down buttons to move the cursor to
ENHANCE. Push the Set button to display the ENHANCE
MENU.
◆ ◆ ◆ ◆ ENHANCE ENHANCE ＭＥＮＵ ENHANCE ENHANCE ＭＥＮＵ ＭＥＮＵ ＭＥＮＵ
> > > >
ＣＨＲＯＭＡ ＣＨＲＯＭＡ ＣＨＲＯＭＡ ＣＨＲＯＭＡ ： ： ： ： ０００ ０００ ０００ ０００
ＤＥＴＡＩＬ ＤＥＴＡＩＬ ： ： ： ： ０００ ０００ ↑ ↑ ↑ ↑
ＤＥＴＡＩＬ ＤＥＴＡＩＬ ０００ ０００
ＰＥＤＥＳＴＡＬ ＰＥＤＥＳＴＡＬ ： ： ： ： ０００ ０００
ＰＥＤＥＳＴＡＬ ＰＥＤＥＳＴＡＬ ０００ ０００
ＧＡＭＭＡ ＧＡＭＭＡ ＧＡＭＭＡ ＧＡＭＭＡ ：ＯＮ ：ＯＮ ：ＯＮ ：ＯＮ ↑ ↑ ↑ ↑
ＰＯＬＡＲＩＴＹ ＰＯＬＡＲＩＴＹ ：ＰＯＳＩＴＩＶＥ ：ＰＯＳＩＴＩＶＥ
ＰＯＬＡＲＩＴＹ ＰＯＬＡＲＩＴＹ ：ＰＯＳＩＴＩＶＥ ：ＰＯＳＩＴＩＶＥ
ＭＩＲＲＯＲ ＭＩＲＲＯＲ ＭＩＲＲＯＲ ＭＩＲＲＯＲ ：ＯＮ ：ＯＮ ：ＯＮ ：ＯＮ
ＦＯＧ ＦＯＧ ＦＯＧ ＦＯＧ ＡＤＪＵＳＴ ＡＤＪＵＳＴ ＡＤＪＵＳＴ ＡＤＪＵＳＴ ：ＯＦＦ ：ＯＦＦ ：ＯＦＦ ：ＯＦＦ
D D D D - - - - ZOOM ZOOM ZOOM ZOOM ：ＯＦＦ ：ＯＦＦ ：ＯＦＦ ：ＯＦＦ
ＲＥＴ ＲＥＴ ＲＥＴ ＲＥＴ
ＥＮＤ ＥＮＤ ＥＮＤ ＥＮＤ
ENHANCE menu
Color level adjustment (CHROMA)
The optimum color level has been set at the factory. If necessary,
this can be changed as follows.
Use the Up and Down buttons to move the cursor toCHROMA
and push the Set button. Right side setting value blinks. In this
state, push the Set button to adjust color level.
Adjustment value range： ： ： ： -128～ ～ ～ ～ 000～ ～ ～ ～ +50
DETAIL fine setting
1) Use the Up and Down buttons to move the cursor to
DETAIL.
2) Simultaneously press the Up and Down buttons for 2
seconds to display
[RESOLUTION MENU].
◆ ◆ ◆ ◆ DETAIL DETAIL MENU MENU ◆ ◆ ◆ ◆
DETAIL DETAIL MENU MENU
> > > >
R E S O L U T I O N R E S O L U T I O N ： ： ： ： N O R M A L N O R M A L
R E S O L U T I O N R E S O L U T I O N N O R M A L N O R M A L
ＲＥＴ ＲＥＴ ＲＥＴ ＲＥＴ
ＥＮＤ ＥＮＤ
ＥＮＤ ＥＮＤ
DETAIL menu
RESOLUTION setting
Use the Up and Down buttons to move the cursor to
RESOLUTION and push the Set button. Right side setting
value blinks. In this state, push the Set button to change
resolution setting.
Set button : NORMAL→HIGH
NORMAL : Standard resolution setting
HIGH : Resolution is set higher than standard.
(Factory setting)
◆ ◆ ◆ ◆
......Color level adjustemnt
......Detail adjustment
↑ ↑ ↑ ↑ ......Black level adjustment
......Gamma setting
......Picture polarity(negative positive)
......Left and right reverse display
......Fog adjustment
↵ ↵ ↵ ↵
......Digital zoom menu
↵ ↵ ↵ ↵
......Return to Main menu
......End(Menu display off）
the resolution setting
......Resolution mode
......Return to Sub menu
......End(Menu display off）
Simultaneously press the Up and Down buttons for 2 seconds
to return to the factory setting(000).
In this state, pressing Set button will stop blinking and setting
value will be fixed.
Note
1) Color noise might be there, when color level is
increased too much.
2) In case of black and white picture mode of BW
MODE, the CHROMA level can not be fixed to -128.
Detail setting (DETAIL)
The optimum detail level has been set at the factory.
If necessary, this can be changed as follows.
Use the Up and Down buttons to move the cursor to DETAIL
and push the Set button. Right side setting value blinks. In this
state, push the Set button to adjust detail level.
Adjustment value range： ： ： ： -128～ ～ ～ ～ 000～ ～ ～ ～ +127
Note
Noise might be there, when detail level is increased too
much.
33
Note
There might be ringing effect in counter depending on the
subject, in case of high resolution.
menu
Black level setting (PEDESTAL)
The optimum black level has been set at the factory.
If necessary, this can be changed as follows.
Use the Up and Down buttons to move the cursor to
PEDESTAL and push the Set button. Right side setting value
blinks. In this state, push the Set button to adjust black level.
Adjustment value range： ： ： ： -28～ ～ ～ ～ 000～ ～ ～ ～ +100
Simultaneously press the Up and Down buttons for 2 seconds
to return to the factory setting(000).
34