Table of Contents
Advertisement
Installation
(Continued)
Please check that all installation hardware listed below are included.
❑ Installation Hardware
(For Mounting)
No.
Item
Hex. Bolt with Double Washers (4 mmφx 8 mm)
q
YJT034C707ZA
43
Base Bracket
w
YFG014C920ZC
Hex. Nut (5 mmφ)
e
YJN014C703ZA
Mounting Bracket (L)
r
YFX214C387ZA
Mounting Bracket (R)
t
YFX214C386ZA
Double-Faced Adhesive Tape
y
YFX9994C725ZA
Note: For installation, use the screws shorter than 5 mm if you should use the screw other than above Hex. Bolt with Double
Washers q .
❑ Installation Hardware
(For wiring)
No.
Item
Extension Cord (5 m)
u
(BRAKE / VIDEO-CONT / ACC / BATT/ DIN / RCA / GND)
YAJ024C107ZA
Clip Connector
i
YEAT034C012
Remote Control Sensor (cable length 3 m)
o
YEFX9991540
Remote Control Sensor Extension Cord (3 m)
!0
YAJ074C024ZA
Cord Clamp
!1
(for Remote Control Sensor)
YEFX007570
Double-Faced Adhesive Tape
!2
(for Remote Control Sensor)
YFX994C124ZA
Note:
¡The number in parenthesis underneath each accessory part name is the part number for maintenance and service.
¡Accessories and their parts numbers are subject to modification without prior notice due to improvements.
44
CX-DH801W
Diagram
Qty
4
2
4
1
1
2
Diagram
Qty
1
1
1 set
1
2
1
Installation Location
Avoid installing the unit in the following locations.
¡In areas hit by direct sunlight, hot air from the heater, or any other high-temperature location.
¡In an area where you cannot firmly secure the unit, or in high-vibration areas.
¡In areas with high humidity or high dirt and dust levels.
Select the mounting angle
Default: H
Use a screwdriver to set the angle-adjusting screw to the position "V" or "H", depend-
ing on the mounting angle selected.
This unit can be set in the five directions: horizontal, vertical, and the positions A
(22.5°), B (45°), and C (67.5°). Mount the unit by referring to the figures below.
Cautions:
¡Set the angle-adjusting screw to the same angle as the unit is installed.
¡Set the holes to the same positions for both left and right.
V
C
V
C
B
B
H
H
C
B
A
H
C
B
A
V
R
V
R
V
A
A
M4×5mmMA×
HA
V.A.B
22.5°
H
H
H (0°)
A (22.5°)
A (22.5°)
H
H
H
H
V
V
V
V
(L)
(R)
(L)
(R)
Installation
Typical horizontal installation
(Normal)
(Up-side down)
Typical vertical installation
Do not tilt in this
direction.
(Normal)
(Up-side down)
Limit to less than
10 degrees.
H
H
Adjust the angle with a screw driver
V
C
V
C
V
B
B
H
H
C
B
A
C
B
A
C
V
R
V
R
A
A
67.5 °
45 °
H
H
B (45°)
B (45°)
C (67.5°)
V (90°)
H
H
H
H
H
V
V
V
V
(L)
(R)
(L)
(R)
(L)
Angle
Selecting a mounting angle
H
Limit to less than 10 degrees.
Set the screw to the
same positions for
both left and right.
Limit to less
H
than 10
degrees.
Set the screw to the
same positions for
both left and right.
CX-DH801W
44
V
V
C
B
H
B
A
V
R
A
H
H
V
V
(R)
(0˚)
V
(90˚)
V
45
Advertisement
Table of Contents
