Page 1
Teléfonos inalámbricos Contenido y precauciones de seguridad Controles de operación FT-8509 Procedimientos de alineamiento Diagrama a bloques Diagramas esquemáticos Procedimiento de localización de fallas Carta de voltajes de transistores y de IC Identificación de terminales de semiconductores Localización de partes eléctricas Diagramas de conexiones (alambrado) Vistas explotadas y lista de partes mecánicas...
ALIGNMENT PROCEDURE Test Mode For Base Unit Press the “*” and “#” keys at the same time about 1.5 seconds while turning the power on, the confirmation beep will sound to indicate that the unit is in the test mode. 1.
Page 6
Test Mode For Handset Unit To perform the TEST mode, turn the power ON by pressing the “*” and “#” buttons at the same time. When entered the TEST mode, the bell rings and the unit enters TEST mode 1. (Refer to the following table.) 1.
Page 7
Base Unit Transmitter Section AF GEN. BASE Unit Test Point Power Connections Meter DC IN TEL Line 1kHz 77.6mV Jack 9V Jack Test Point Frequency Counter AC 120V 60Hz Adapter Deviation Meter Preset Place the Base unit in VCO/TX FREQ. ADJ mode in accordance with the procedure on page 3. Alignment Procedure step Adjustment...
Page 8
Receiver Section BASE Unit AC Voltmeter RF SG Dummy Load Connections (600-ohm) TEL Line Test Point Jack DC Voltmeter Terminal DC IN 9V Jack AC 120V 60Hz Adapter Preset Place the Base unit in RX SENS mode (step 4) in accordance with the procedure on page 3. Alignment Procedure step Preset to...
Page 9
Handset Unit Transmitter Section HANDSET Unit AF GEN. Power Test Point Connection Meter J401 Batter 1kHz 9mV Terminals MIC+Pin Test Point Frequency Counter DC Power Supply Deviation Meter DC 3.8V Preset Place the Handset in VCO/TX FREQ. ADJ mode in accordance with the procedure on page 4. Alignment Procedure step Adjustment...
Page 10
Receiver Section HANDSET Unit AC Voltmeter Connections RF SG Dummy Load (150-ohm) Test Point Connector J401 DC Power Supply DC Voltmeter Terminal Batter Terminal DC 3.8V Preset a) Connect the handset RF unit to the handset main unit. b) Connect DC power supply to battery connector on the handset unit. c) Turn the DC power supply ON while pressing “*”...
TROUBLESHOOTING HINTS 1. The bell does not ring. When the INTCOM key of See 2. The bell does not the base is pressed, does ring & page does not ring. the ringer on the handset ring? When the TEL SG is joined Check IC5 and TEL network with the base to make bell circuit.
Page 17
2. The bell does not ring & page does not ring. Can the base and handset See 3. The base and handset be connected? cannot be connected. Press handset DIAL key When the key of the handset Check IC404. while in TALK MODE. is pressed, can the pulse Can key touch sound be output at pin 38 of IC404 be...
Page 18
3. The base and handset cannot be connected. Check whether Check IC10 and its base is able to set in the peripheral circuit. test mode 1. Check the TX POWER Check base RF unit. and the TX FREQUENCY on the base unit. Set the base in the test Check whether there is Check RT3, R56, C60,...
Page 19
Set the handset in the Check whether there is Check RT403, R441, test mode 3, check a 250 Hz data R442, R443, R444, whether deviation of the waveform at C453. R445 and C453. TX data is app. 8 kHz Dev. Check handset RF unit.
Page 20
4. Will not dial out. (TONE) Check whether there is a Check IC10, Q15 and their DTMF waveform on Pin 1 of peripheral circuits. IC10. Check whether there is a Check IC1. DTMF waveform on Pin1 of IC1. (PULSE) Check whether there is a Check IC10 pulse on Pin 10 of IC10.
Page 21
5. TROUBLE WITH INTERCOM MODE 5-1. The voice from the Base unit cannot be heard on the Handset. Check whether there is an Check MC251 and IC7. audio waveform on Pin 4 of IC7. Check Pin 7 of IC6. 5-2. The voice from the Handset cannot be heard on the Base unit. Check whether there is an Check IC6.
Page 22
6. TROUBLE WITH SPEAKERPHONE MODE 6-1. The voice of the caller cannot be heard (INCOMING CALL). Check whether there is an Check IC1. audio waveform on Pin 7 of IC1. Check whether there is an Check IC6, RL1 and Q6. audio waveform on Pin 1 of IC6.
IC AND TRANSISTOR VOLTAGE CHART Base Unit Unit [V] Unit [V] Ref No. PIN STBY TALK NOTE Ref No. PIN STBY TALK NOTE FLOAT FLOAT 4.1-6.0 4.1-6.0 SINE WAVE 4.0-5.0 4.0-5.0 SINE WAVE 4.5-5.0 PULSE 4.5-5.0 1.5-3.0 2.0-2.4 0.3-2.0 0.5-0.8 OPEN 2.5-3.0 OPEN...
Page 24
Unit [V] Unit [V] Ref No. PIN STBY TALK NOTE Ref No. PIN STBY TALK NOTE 0.0/5.2 0.0/5.2 Depend on VOL SW 5.2/0.0 5.2/0.0 Depend on VOL SW 0.0/5.2 0.0/5.2 TONE/PULSE IC10 TX MUTE RX MUTE 0.0-0.5.0 0.0-0.5.0 SINE WAVE -0.4-5.0 -0.4-5.0 SINE WAVE...
Page 26
Handset Unit [V] Unit [V] Ref. No. PIN STBY TALK NOTE Ref. No. PIN STBY TALK NOTE 2.0(AC) 0-3.5 2.0(AC) OPEN OPEN IC401 0-0.3 OPEN OPEN OPEN OPEN 0-2.0 0-2.0 0-1.5 0-0.4 0-0.4 0-0.4 1.0-3.0 IC404 0-1.8 1.0-3.0 OPEN 0-3.0 0-1.0 IC403 0-3.0...
PARTS LIST PRODUCT SAFETY NOTE : Products marked with a have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice of this service manual. Don’t degrade the safety of the product through important servicing. Symbol Symbol ±...
Page 40
LOC. REF. PART NO. DESCRIPTION RC008392 BCML811835Z CERAMIC M/L (1608) TAPE 0.018UF 50V K B RC004171 BCXT515635Z CERAMIC M/L (2125) TAPE 0.056UF 25V K B RC008757 BCMM818204Z CERAMIC M/L (1608) TAPE 82PF 50V J CH RC004138 BCAZ811006Z ELECTROLYTIC 10UF 50V M C-156 RC008843 BCML313335Z CERAMIC M/L (1608) TAPE...
Page 41
LOC. REF. PART NO. DESCRIPTION C104 RC008060 BCML811225Z CERAMIC M/L (1608) TAPE 0.0012UF 50V K B C105 RC005214 BCMM812214Z CERAMIC M/L (1608) TAPE 220PF 50V J CH C106 RC005208 BCML814725Z CERAMIC M/L (1608) TAPE 0.0047UF 50V K B C107 RC002234 BCXT814735Z CERAMIC M/L (2125) TAPE 0.047UF 50V K B...
Page 42
LOC. REF. PART NO. DESCRIPTION C445 RC004347 BCXK514740Z CERAMIC M/L (2125) TAPE 0.47UF 25V Z F C446 RC005205 BCML811035Z CERAMIC M/L (1608) TAPE 0.01UF 50V K B C447 RC004412 BCXT312245Z CERAMIC M/L (2125) TAPE 0.22UF 16V K B C448 RC005275 BCML813925Z CERAMIC M/L (1608) TAPE 0.0039UF 50V K B...
ASSEMBLY PARTS LIST LOC. REF. PART NO. DESCRIPTION RC008428 AC220BLBA MAIN PCB ASSEMBLY, BASE RC008429 AC220BLBC KEY PCB ASSEMBLY, BASE RC008430 AC220BLPA MAIN PCB ASSEMBLY, HANDSE...