OPERATING CONTROLS HANDSET CONTROLS AND FUNCTIONS SETTING THE DIAL MODE 1 Press and hold until you hear FLASH Antenna a confirmation tone. 2 To set the dial mode for pulse dialing, press . Or to set the dial mode for tone dialing press .
ANSWERING MACHINE SETTING THE CLOCK 1. Press twice, then press MENU 2. Select the day of the week by pressing . When the correct day is announced, SELECT SELECT press 3. Select the hour by pressing . When the correct hour is announced, press SELECT SELECT 4.
ALIGNMENT PROCEDURE Base Unit Transmitter Section Connections BASE Unit AF GEN. Test Point Power Meter DC IN TEL Line 1kHz -15dBm 9V Jack Jack Test Point Frequency Counter AC 120V Adapter 60Hz Deviation Meter Preset Press and hold the “ANSWER” key about 5.0 seconds while turning the 7. SEG LED shows “8” . Alignment Procedure step Adjustment...
Page 6
Receiver Section Connections BASE Unit AC Voltmeter RF SG Dummy Load (600-ohm) TEL Line Test Point Jack DC Voltmeter DC IN 9V Jack Test Point AC 120V 60Hz Adapter Preset Place the Base Unit in RX SENS mode (step 11) in accordance with the precedure on page 4. Alignment Procedure step Preset to...
Page 7
Handset Unit Transmitter Section Connections HANDSET Unit AF GEN. Test Point Power Meter J601 Battery 1kHz 9mV MIC+Pin Connector Test Point Frequency Counter DC Power Supply Deviation Meter DC 3.8V Preset a) Connect the handset RF unit to the handset main unit. b) Connect DC power supply to battery connector on the handset unit.
Page 8
Receiver Section Connections HANDSET Unit AC Voltmeter RF SG Dummy Load (150-ohm) Test Point Terminal DC Power Supply J601 DC Voltmeter Battery Test Point Connector DC 3.8V Preset a) Connect the handset RF unit to the handset main unit. b) Connect DC power supply to battery connector on the handset unit. c) Turn the DC power supply ON while pressing “...
TROUBLESHOOTING HINTS 1. The bell does not ring. Set RINGER volume setting Check RINGER mode setting to Hi or Low. is Hi or Low. See 2. The bell does not ring When the PAGE SW of the & page does not ring. base is pressed, does the ringer on the handset ring? When the TEL SG is joined...
Page 14
2. The bell does not ring & page does not ring. Can the base and handset be See 3. The base and handset connected? cannot be connected. Press handset DIAL key When the key of the handset is Check IC604. while in TALK MODE.
Page 15
3. The base and handset cannot be connected. Check whether the base Check IC4 and its is able to set in the test peripheral circuit. mode 8. Check the TX POWER Check base RF unit. and the TX FREQUENCY on the base unit. Set the base in the test Check whether there is a Check RT3, R76, R91,...
Page 16
Set the handset in the Check whether there is a Check RT603, R641, test mode 3, check 250 Hz data waveform at R642, R643, R644, whether deviation of the “MOD” of RF unit. R645 and C653. TX data is app. 9.0 kHz Dev.
Page 17
4. Cannot make a phone call (pulse). Can the base and handset See 3. The base and handset be connected? cannot be connected. While in TALK MODE, press Check IC4. dial key of the handset. Check whether square waveform from pin 80 of IC4 is fed.
Page 18
6. Voice cannot be transmitted to other party (outgoing call). Can the base and handset be See 3. The base and handset connected? cannot be connected. The 1 kHz, 9.0mV sine Check Q604 and its wavefor m i s a p p l i e d t o peripheral circuit.
Page 19
7. The voice of the caller cannot be heard (incoming call). Can the base and handset be See 3. The base and handset connected? cannot be connected. The 1 kHz, -15dBm sine Check the base TEL-line waveform is applied to TEL- circuit and REPLAY control line of the base, can the 1 kHz circuit.
EXPLODED VIEW AND MECHANICAL PARTS LIST RF MODULE (HANDSET) HANDSET MAIN PCB ASSY BASE MAIN PCB ASSY SP751 RF MODULE SP801 (BASE) BASE KEY PCB ASSY AT751 — 32 —...
Page 32
LOC. PART NO. REF NO. DESCRIPTION RC009896 GNBZ366565Z BUTTON, FUNCTION RC009557 GNBZ447715Z BUTTON, FUNCTION RC009897 GNBZ467967Z BUTTON, FUNCTION RC009898 GNBZ467968Z BUTTON, PUSH PMMA RC009894 GCAS266581Z CASE, BOTTOM RC009893 GCAS266564Z CASE, TOP RC009325 HTML446079Z CHARGE TERMINAL C5191(PBP) RC009396 GCAS346381Z DISPLAY WINDOW PMMA RC009837 LFUT494200Z...
PARTS LIST PRODUCT SAFETY NOTE: Products marked with a have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice of this service manual. Don’ t degrade the safety of the product through important servicing. Symbol Symbol ±1...
Page 34
LOC. PART NO. REF NO. DESCRIPTION RC005468 BCEQ904706Z ELECTROLYTIC 47UF 6.3V M C-125 RC005202 BCML311045Z CERAMIC M/L 0.1UF 16V K B RC005202 BCML311045Z CERAMIC M/L 0.1UF 16V K B RC008269 BCML316835Z CERAMIC M/L 0.068UF 16V K B RC005202 BCML311045Z CERAMIC M/L 0.1UF 16V K B RC005203 BCML512235Z...
Page 35
LOC. PART NO. REF NO. DESCRIPTION C109 RC005205 BCML811035Z CERAMIC M/L 0.01UF 50V K B C110 RC004445 BCAZ903316Z ELECTROLYTIC 330UF 6.3V M C-156 C111 RC005205 BCML811035Z CERAMIC M/L 0.01UF 50V K B C112 RC001794 BCAZ111016Z ELECTROLYTIC 100UF 10V M C-156 C113 RC005202 BCML311045Z...
Page 36
LOC. PART NO. REF NO. DESCRIPTION C170 RC005401 BCXT111055Z CERAMIC M/L (2125) 1UF 10V K B C171 RC009567 BCXS311055Z CERAMIC M/L (3216) 1UF 16V K B C601 RC005216 BCMM813304Z CERAMIC M/L 33PF 50V J CH C602 RC008731 BCXK311050Z CERAMIC M/L (2125) 1UF 16V Z F C603 RC005202...
ASSEMBLY PARTS LIST NOTE: Following part numbers are not available as replacement parts. Order parts necessary for repair or contact the Toshiba Factory Service Center. LOC. PART NO. REF NO. DESCRIPTION RC009876 AC315BHBA BASE MAIN PCB ASSEMBLY RC009877 AC315BHBC BASE KEY PCB ASSEMBLY...
SPECIFICATIONS MEASUREMENT CONDITIONS 1. Standard Voltage: DC 3.8 V ±0.025 V Portable Unit AC 120 V ±3 V 60 Hz Base Unit 25 °C ±5 °C 2. Temperature: 3. Channel: Portable (TX Frequency) Base (TX Frequency) 904.052470 MHz 925.997470 MHz 902.102465 MHz 926.047470 MHz 902.152465 MHz...
Page 47
BASE UNIT RECEIVER Unit Nominal Limit −115 < −107 1. Sensitivity 12 dB SINAD (with CCITT Filter) 2. Frequency Response (Ref: 1 kHz) −5.0 −9.0 ~ −1.0 0.3 kHz −8.0 −12.0 ~ −4.0 3.0 kHz 3. Distortion at 1 mV RF Input <...
Page 48
HANDSET UNIT RECEIVER Unit Nominal Limit −115 1. Sensitivity 12 dB SINAD (with CCITT Filter) <−107 2. AF Frequency Response (Ref: 1 kHz) 0.3 kHz 1.5 ~ 9.5 −17.0 −21.0 ~ −13.0 3.0 kHz −7 −10 ~ −4 3. Audio Output Level VOL.
Page 49
TOSHIBA AMERICA CONSUMER PRODUCTS, INC. 82 TOTOWA ROAD, WAYNE, N.J. 07470 TOSHIBA HAWAII, INC. 327 KAMAKEE ST., HONOLULU, H.I. 96814...