Table of Contents
Advertisement
Standard characters
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x11x12x13x14x
1
1)
1
£
$
¥
2
a
b
c
2
ä
I
d
e
f
3
ë
4
g
h
i
4
ï
5
j
k
l
5
L
m n
o
6
ö
M
p
q
r
s
7
N
t
u
v
8
ü
O
w x
y
z
9
Q
.
,
?
!
0
P
*
/
(
)
< = > %
#
Abc
123
# @
\
-->
-->
123
abc
1) Space
Arabic
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x
1
1 $
1)
2
2 a b c
I
4
4 g h
5
5
L
6 m n o
M
7 p q r
N
O
9 w x y z
Q
.
,
?
!
0 + -
P *
/
(
) < = > %
#
Abc
123
# @ \ &
-->
-->
abc
123
1) Space
Specifications
Recommended batteries
Nickel-metal-hydride (NiMH):
V30145-K1310-X383
(Valid at the time of going to press)
The handset is supplied with recommended
batteries.
Base station power consumption
In standby mode
– Handset in base station
– Handset outside base station
During a call
General specifications
DECT standard
GAP standard
Range
Base station power supply
Environmental conditions
in operation
¤
á
à
â
ã
ç
é
è
ê
í
ì
î
ñ
ó
ò
ô
õ
ß
ú
ù
û
ÿ
ý æ ø
å
+
-
:
¿
¡
"
'
&
§
3 d e
i
j
k
l
s
8 t u v
:
"
'
ca. 1.0 W
ca. 0.8 W
ca. 1.0 W
is supported
is supported
(the Gigaset handset ope-
rates only with a Gigaset
base)
up to 300 m outdoors
up to 50 m indoors
230 V ~/50 Hz
+5 °C to +45 °C, 20% to
75% elative humidity
11
Questions and answers
If you have any queries about the use of your tele-
phone, visit our website at
www.gigaset.com/service
for 24-hour support. The table below contains a list of
common problems and possible solutions.
Problem
Nothing
appears in
the display.
;
_
No wireless
connection
to the base sta-
tion,
Base flashes in
the display.
f
You cannot
hear a ringer/
dialling tone
from the fixed
line network.
;
_
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
Authorisation
This device is intended for connection to analogue
networks outside the EEA (with the exception of Swit-
zerland) depending on national type approval.
Country-specific requirements have been taken into
consideration.
We, Gigaset Communications GmbH, declare that this
device meets the essential requirements and other
relevant regulations laid down in Directive 1999/5/
CE.
A copy of the 1999/5/EC Declaration of Conformity is
available at this Internet address:
www.gigaset.com/docs
Cause
Solution
The handset is not
Press the end call
a
switched on.
key
5 seconds or place the
handset in the base
station.
The batteries are
Charge or replace the
flat.
batteries.
The handset is out-
Move the handset
side the range of
closer to the base
the base station.
station.
The handset is not
¢
registered.
Register the handset
The base station is
p. 9.
not turned on.
Check the mains con-
¢
nector on the base sta-
tion
The phone cord
Please always use the
supplied has not
phone cord supplied or
been used or has
ensure that the
been replaced by a
pin connections are
new cord with the
correct when purchas-
wrong jack con-
ing from a retailer:
nections.
3-4 assignment of
telephone leads/
EURO CTR37.
The system PIN you
Reset the system PIN to
¢
have entered is
the default 0000
incorrect.
p. 10.
All handsets are
de-registered. All set-
tings are reset. All lists
are deleted.
for approx.
p. 3.
Advertisement
Table of Contents
