Siemens MICROMASTER 440 Operating Instructions Manual page 69

Issue B1
Par. No.
P2187[3]
P2188[3]
P2189[3]
P2190[3]
P2191[3]
P2192[3]
r2197
r2198
PI Controller (P0004 = 22)
Par. No.
P2200[3]
P2201[3]
P2202[3]
P2203[3]
P2204[3]
P2205[3]
P2206[3]
P2207[3]
P2208[3]
P2209[3]
P2210[3]
P2211[3]
P2212[3]
P2213[3]
P2214[3]
P2215[3]
P2216
P2217
P2218
P2219
r2224
P2225
P2227
P2231[3]
P2232
P2240[3]
r2250
P2253[3]
P2254[3]
P2255
P2256
P2257
P2258
r2260
MICROMASTER 440 Operating Instructions
6SE6400-5AC00-0BP0
Parametername
Upper torque threshold 2
Lower torque threshold 2
Upper torque threshold 3
Lower torque threshold 3
Belt failure speed tolerance
Time delay for belt failure
CO/BO: Monitoring word 1
CO/BO: Monitoring word 2
Parametername
BI: Enable PID controller
Fixed PID setpoint 1
Fixed PID setpoint 2
Fixed PID setpoint 3
Fixed PID setpoint 4
Fixed PID setpoint 5
Fixed PID setpoint 6
Fixed PID setpoint 7
Fixed PID setpoint 8
Fixed PID setpoint 9
Fixed PID setpoint 10
Fixed PID setpoint 11
Fixed PID setpoint 12
Fixed PID setpoint 13
Fixed PID setpoint 14
Fixed PID setpoint 15
Fixed PID setpoint mode - Bit 0
Fixed PID setpoint mode - Bit 1
Fixed PID setpoint mode - Bit 2
Fixed PID setpoint mode - Bit 3
CO: Act. fixed PID setpoint
Fixed PID setpoint mode - Bit 4
Fixed PID setpoint mode - Bit 5
Setpoint memory of PID-MOP
Inhibit rev. direct. of PID-MOP
Setpoint of PID-MOP
CO: Output setpoint of PID-MOP
CI: PID setpoint
CI: PID trim source
PID setpoint gain factor
PID trim gain factor
Ramp-up time for PID setpoint
Ramp-down time for PID setpoint
CO: Act. PID setpoint
5 System parameters
Default Level DS
99999.0 2 CUT
0.0 2 CUT
99999.0 2 CUT
0.0 2 CUT
3.00 2 CUT
10 2 CUT
- 2 -
- 2 -
Default Level DS
0:0 2 CT
0.00 2 CUT
10.00 2 CUT
20.00 2 CUT
30.00 2 CUT
40.00 2 CUT
50.00 2 CUT
60.00 2 CUT
70.00 2 CUT
80.00 2 CUT
90.00 2 CUT
100.00 2 CUT
110.00 2 CUT
120.00 2 CUT
130.00 2 CUT
130.00 2 CUT
1 3 CT
1 3 CT
1 3 CT
1 3 CT
- 2 -
1 3 CT
1 3 CT
0 2 CUT
1 2 CT
10.00 2 CUT
- 2 -
0:0 2 CUT
0:0 3 CUT
100.00 3 CUT
100.00 3 CUT
1.00 2 CUT
1.00 2 CUT
- 2 -
QC
N
N
N
N
N
N
-
-
QC
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
-
N
N
N
N
N
-
N
N
N
N
N
N
-
69