Advertisement
2.3 Communication Specifications
Item
Specifications
Conforming to RS232
GOT communication
Transmission speed :115,200bps
Connector shape
: MINI DIN 6Pins (Male)
Conforms to USB2.0 (Full speed is supported.)
(Performs the conversion between USB and serial in
PC communication
GT10-LDR. After serial conversion, transmission
speed is 115.200bps.)
Connector shape
:USB MINI-B 5Pins (Receptacle)
3. External Dimensions
External Dimensions
14
70 (2.75")
(0.55")
Unit: mm (inch)
Weight: 0.2kg
4. Part Name
1)
2)
3)
4)
5)
7)
8)
No.
Name
1)
POWER LED
LED to show power status
2)
SET/RUN LED
LED to show that the settings are being checked/the transfer is running
3)
ERROR LED
LED to show error status
4)
RD/WR selection switch
Switch to select read/write direction
5)
Data selection switch
Switch to select the data to be transferred
6)
ENT key
Switch to determine the transfer direction and the data to be transferred, and to start the transfer
2.4 Power Supply Specifications
Item
Specifications
DC5V (DC4.75 to 5.25V)
Input power supply voltage
Supplied from the GOT or PC (Supplied from bus
power)
Fuse
Power consumption
0.7W (140mA/DC5V) or less
Cable length
240 (9.44 ")
12)
13)
6)
9)
Specifications
No.
Name
7)
Write protection switch
8)
USB port
9)
Reference plate (operating instructions)
-
10)
Reference plate (error contents)
11)
Transfer cable
12)
Strap hole
13)
Part to be labeled
14)
Rating plate (Nameplate)
5. LED lighting specification
LED Name
Status
POWER LED is lit.
POWER
POWER LED is not lit.
POWER LED is not lit.
Orange light
SET/RUN
Green flashing
Green light
Red flashing
Unit: mm (inch)
POWER LED is not lit.
1
Green light*
1
Green flashing*
1
ERROR
Red light*
1
Red flashing*
1
Red
Green*
Orange
Green*
*1 An error message appears on the GOT screen. Apply remedies according to the display.
Refer to the "Chapter 12 Troubleshooting" for details on handling errors.
6. Switch operation specification
10)
Switch Name
Switch to select read/write direction
RD/WR selection
11)
RD : The data is read out from the GOT to the memory loader.
switch
WR : The data is written from the memory loader to the GOT.
Switch to select the data to be transferred
When reading out the data from the GOT to the memory loader
[PROJECT + OS] : The standard monitor OS, communication driver, project data, and resource data are read out from the GOT to the memory
loader.
14)
Data selection switch
[PROJECT] : The project data and resource data are read out from the GOT to the memory loader.
When writing the data from the memory loader to the GOT
[PROJECT + OS] : The standard monitor OS, font data, communication driver, and project data are written from the memory loader to the GOT.
[PROJECT] : The project data is written from the memory loader to the GOT.
Switch to prevent the memory loader from being written to the data
Write protection switch
ON : The data cannot be written neither from the GOT or a PC (GT Designer2, GT Designer3) to the memory loader.
OFF : The data can be written from the GOT or a PC (GT Designer2, GT Designer3) to the memory loader.
Switch to determine the transfer direction and the data to be transferred, and to start the transfer
The transfer starts by pressing the key twice.
The first pressing of the key determines the read/write direction and the data to be transferred.
(After the read/write direction and the data to be transferred are determined, if RD/WR selection switch and Data selection switch are operated,
ENT key
the operations that have been made will be canceled.)
(The ENT key must be pressed within 30 seconds after the first pressing of the ENT key. Failure to do so cancels the operations that have been
made.)
The second pressing of the key starts the transfer.
*1 When the standard monitor OS and communication driver are transferred from the memory loader to the GOT, starting up the GOT with OS installation screen is
required.
Switch to prevent the memory loader from being written to the data
Connection port with a PC (with protection cap)
Described operating instructions of the memory loader
Described lighting status of ERROR LED
Cable to be connected with the GOT
A hole to attach a strap
Space to be labeled (created by user)
Power is supplied.
Power is not supplied.
Before starting the transfer.
The transfer direction and the data to be transferred are determined.
The transfer is running.
The transfer is completed.
The transfer is aborted.
No errors
Write protection switch ON
The GOT type that is set in the data to be transferred differs from that of the GOT to which the data is transferred.
The data to be transferred is broken.
The major version of the standard monitor OS is different from that of the project data.
Communication error occurs between the GOT and the memory loader.
Password is set in the project data.
1
OS installation screen is not active
Specifications
Specifications
--
Contents
Advertisement
