Troubleshooting Guide - DeWalt D51236 Instruction Manual

ESPECIFICACIONES DE LA HERRAMIENTA
Height / Hauteur / Altura
Width / Largeur / Anchura
Length / Longueur / Longitud
Weight / Poods / Peso
Recommended Operating Pressure
Pression de fonctionnement recommandée
Presión de funcionamiento recomendada
Air Consumption per 100 cycles
Consommation d'air par 100 cycles
Consumo de aire por cada 100 ciclos
Loading capacity
Capacité de chargement
Capacidad óptima
Compressor will be sufficient for tools at all production rates.
Le compresseur sera suffisant pour les outils à tous les taux de production.
El compresor será suficiente para las herramientas a cualquier velocidad de trabajo
Compressor will be sufficient at slow or moderate production rates, but may have
difficulty at very rapid rates.
Le compresseur est suffisant pour les cadences de production lentes ou modérées, mais
son rendement pourrait être insuffisant pour les cadences très rapides.
El compresor será suficiente a velocidades de trabajo bajas o moderadas, pero puede
tener dificultades en velocidades muy rápidas.
Compressor will be adequate only when tools are utilized at slow production rates.
(punch-out or occasional use)
Le compresseur est adéquat uniquement quand les outils sont utilisés à des cadences de
production lentes (perforation ou utilisation occasionnelle).
El compresor sólo será adecuado cuando las herramientas se utilicen en velocidades de
trabajo lentas (perforación o uso ocasional).
Not Recommended
Non recommandé
No recomendado
MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS,
WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, ALWAYS DISCONNECT AIR FROM TOOL BEFORE ALL REPAIRS.
Trigger valve housing leaks
Top cap leaks air
Exhaust leaks
Air leaks around nose when
tool is at rest. (Driver blade in up position)
Air leaks around nose when tool is in
actuated position. (Driver blade in
down position)
Tool does not cycle in cold weather
Lack of power; sluggish
Skipping nails; intermittent feed
Fasteners jam in tool
TOOL SPECIFICATIONS
CARACTÉRISTIQUES DE L'OUTIL
D51236
8.2'' (209 mm)
2.6'' (67 mm)
9.6'' (245 mm)
2.4 lbs. (1.1 kg)
70 - 120 psig (4.8 to 8.3 bar, 5 to 8.5 kg/cm
2
de 70 à 120 lb/po
2
(de 5 à 8,5 kg/cm ou de 4,9 à 8,3 bar)
2.1 cfm
2,1 cfm
2,1 cfm
Up to 110 Nails
Jusqu'a 110 clous
Hasta 110 clavos

Troubleshooting Guide

CONTACT A D WALT SERVICE CENTER OR CALL 1-(800)-4-D
E
O-ring or valve stem failure
Loose cap screws
Damaged or worn gasket or o-ring
Main seal or o-ring damaged, debris in tool.
Damaged or worn o-rings
Damaged or worn bumper
Tool not receiving air
Valve may be frozen
Damaged or worn o-rings
Broken or damaged driver blade
Low air pressure
Lack of lubrication
Damaged or worn o-rings
Exhaust port blocked or clogged
Air restricted
Lack of lubrication
Nose piece screws loose
Wrong size/angle fasteners
Dirty magazine
Worn magazine
Broken or damaged driver blade
Trigger valve o-ring worn or damaged
Worn piston o-ring
Worn or damaged pusher spring
Magazine loose
Driver channel in nose piece worn
Wrong size/ angle fasteners
Magazine loose
Worn driver blade
Nose piece screws loose
Nails not feeding properly
D51238
8.5'' (215.9 mm)
2.8'' (58.4 mm)
9'' (228.6 mm)
2.8 lbs. (1.3 kg)
2
) 70 - 120 psig (4.8 to 8.3 bar, 5 to 8.5 kg/cm
2
de 70 à 120 lb/po
2
(de 5 à 8,5 kg/cm ou de 4,9 à 8,3 bar)
3.5 cfm @ 100 psi
3 2
3,5 pi /mn @ 100 lb/po
3.5 cfm @ 100 psi
Up to 110 Nails
Jusqu'a 110 clous
Hasta 110 clavos
Replace valve using: Trigger Valve Kit
Tighten cap screws using appropriate Allen wrench
Replace gasket/o-rings using: O-ring Repair Kit
Replace gasket/o-rings using: O-ring Repair Kit
Replace gasket/o-rings using: O-ring Repair Kit
Replace bumper using: Brad Nailer Bumper Kit
Check air supply
Warm up tool
Replace gasket/o-rings using: O-ring Repair Kit
Replace Driver Blade Kit for Brad Nailer
Check air supply
Lubricate tool using approved pneumatic tool oil.
Replace gasket/o-rings using: O-ring Repair Kit
Disconnect air, remove exhaust plate from top
of tool, clean port
Check air supply and couplers
Lubricate tool using approved pneumatic tool oil
Tighten nosepiece screws using appropriate Allen wrench
Use only recommended fasteners
Clean magazine track and nosepiece
Replace magazine
Replace Driver Blade Kit for Brad Nailer
Replace valve using: Trigger Valve Kit
Replace Piston o-ring using: O-Ring Repair Kit
Replace spring
Check that magazine latch is holding firmly
Replace nosepiece
Use only recommended fasteners
Check that magazine screws are holding firmly
Replace Driver Blade Kit for Brad Nailer
Tighten nosepiece screws using appropriate Allen wrench
Ensure nails are feeding properly into nose.
2
)
8 HP Gas
Portable 5.5 HP Gas
Handcarry
2 HP Elec.
3.2 - 4
8 - 9 CFM
CFM
5,5 HP
Essence
Portable à Essence 2
la main
HP Élec.
3,2 à 4 8 à 9
pi 3 /min pi 3 /min
8 HP Gas
5.5 CV Gas
Transporta
2 CV Elec.
ble
8 - 9 CFM
3.2 - 4
CFM
1
2
3
4
5
6
7
8+
WALT.
E
D51236
Cat. #
D510005
D510001
D510001
D510001
D510003
D510001
D512362
D510001
D512362
D510005
D510001
D512362
Industrial
14 - 16 23+ CFM
CFM
Industriel
8 HP
23 pi 3 /min
+
14 à 16
pi 3 /min
Industrial
23+ CFM
14 -16
CFM
D51238
Cat. #
D510005
D512381
D512381
D512381
D512383
D512381
D512382
D512381
D512382
D510005
D512381
D512382