1 Safety Precautions 1.1. GENERAL GUIDELINES 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
1.2.1. Caution for fuse replacement 1.3. Protection Circuitry The protection circuitry may have operated if either of the following conditions are noticed: • No sound is heard when the power is turned on. • Sound stops during a performance. The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are “shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
1.4. Safety Parts Information Safety Parts List: There are special components used in this equipment which are important for safety. These parts are marked by ( ) in the Schematic Diagrams & Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip”...
2.2. Precaution of Laser Diode Caution: This product utilizes a laser diode with the unit turned “on”, invisible laser radiation is emitted from the pickup lens. Wavelength: 790 nm (CDs), 655 nm (DVDs), 405 nm (BDs) Maximum output radiation power from pickup: 100 µW/VDE Laser radiation from the pickup unit is safety level, but be sure the followings: 1.
2.3. Service caution based on Legal restrictions 2.3.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation. The normal solder is the alloy of tin (Sn) and lead (Pb).
2.4. Handling Precautions for BD Drive The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be taken avoid caution to electrostatic breakdown when servicing and handling the laser diode in the BD Drive. Figure 1 Grounding for electrostatic breakdown prevention 2.4.1.
3 Service Navigation 3.1. Service Information This service manual contains technical information which will allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with the original ser- vice manual.
Perform playback for one minute using the RAM disc. No abnormality should be seen in the picture, sound or operation. *Panasonic DVD-RAM disc should be used when recording and play- back. Perform playback for one minute using the BD-Video disc.
4 Specifications HDMI (Deep Color,x.v.Color High Bit rate Audio ) This unit supports “HDAVI Control 5” function. LASER Specification Main unit SA-BT235P Class I LASER Product GENERAL Wave length: Power supply: AC 120 V,60 Hz 790 nm (CDs)/655 nm (DVDs)/405 nm (BDs)
5.5. Speaker Connections Turn off all equipment before connection and read the appropriate operating instructions. Do not connect the AC power supply cord until all other connections are complete. Connect to the terminals of the same colour. 6 PURPLE Subwoofer 5 GREEN Center speaker 2 RED...
6 Operating Instructions 6.1. Removing of disc during abnomality 6.1.1. When the power can be turned off. Step 1 Turn off the power. Step 2 Press & hold [SKIP FWD] button on remote control and [OPEN/CLOSE] button on main unit for 5 seconds. 6.1.2.
7 Self-Diagnostic and Special Mode Setting 7.1. Special Mode Table 1 Self-Diagnostic Function provides information for error to service personnel by Self-Diagnosis Display when any error has occurred. U**, H** and F** are stored in my memory and held. • You can check latest error code by transmitting [0] [1] of Remote Control in Service Mode. Automatic Display on FL will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is Item Key operation...
7.2. Special Mode Table 2 Item FL display Key operation Mode name Description Front Key Demonstration lock/ Ejection of the disc is prohibited. *When lock the tray. When the power is on, press unlock The lock setting is effective until unlocking the [PLAY] and [OPEN/CLOSE] keys tray released...
7.3. Error Code Table 7.3.1. Error Code Table (For BD) Error Code Diagnosis contents Description Monitor Display Automatic FL display Remote control code error Display appears when main unit and remote No display controller codes are not matched. is remote controller code of the main unit.
Page 29
7.3.2. Error Code Table 2 (For BD) Error Code Diagnosis contents Description Monitor Display Automatic FL display SELF Restoration operation Since the power cord fell out during a power No display SELF CHECK CHECK failure or operation, it is under restoration operation.
7.4. Service Mode To enter service mode: While the power is off, press & hold [VOL+] & [OPEN/CLOSE] button on main unit for 3 secs or more follow by [PLAY] button on main unit. 7.4.1. Service Mode Table 1 Item FL display Key operation Mode name...
7.4.2. Service Mode Table 2 Item FL display Key operation Mode name Description (Remote controller key) Laser Used Time Check laser used time (hours) of drive. Press [4] [1] in service mode. Indication ****** (******) is the used time display in hour.
Page 32
7.4.3. Service Mode Table 3 Item FL display Key operation Mode name Description (Remote controller key) BD/DVD drive last error BD/DVD drive error code display. 1. Error Number is displayed for 5 Press [4] [2] in service mode. seconds. **** 2.
Page 33
7.4.4. Service Mode Table 4 Item FL display Key operation Mode name Description (Remote controller key) In case that the maker cannot be 6. Disc maker ID is displayed for 5 identified, display is black out. seconds. 7. Factor of drive error (hexadeci- mal) occurring is left displayed.
Page 34
7.4.5. Service Mode Table 5 Item FL display Key operation Mode name Description (Remote controller key) CEC (H) output Check of the CEC terminal high output of Press [5] [5] in service mode. HDMI. CECHOK CECHNG CEC (L) output Check of the CEC terminal low output of Press [5] [6] in service mode.
8 Troubleshooting Guide 8.1. Troubleshooting Guide for F61 and/or F76 Symptom Checking items Possible Fault(s) Remarks Set cannot ON Faulty AC Cord,Loose connection AC Cord Refer to P5701 soldier crack,dry joint,etc. AC Inlet P5701 SMPS F1 fuse open Fuse F1 P.C.B.
9 Service Fixture & Tools 9.1. Service Tools and Equipment Prepare service tools before process service position. Service Tools Remarks SMPS P.C.B. (JW2*) - Main P.C.B. (CN2004) REXX1037 (10P Cable) Main P.C.B. (CN2006) - D-Amp P.C.B. (CN5402) RFKZBT230P (18P FFC)
10 Disassembly and Assembly Instructions Caution Note: • This section describes the disassembly and/or assembly procedures for all major printed circuit boards & main compo- nents for the unit. (You may refer to the section of “Main components and P.C.B Locations” as described in the service manual) •...
10.3. Disassembly of Top Cabinet Step 1 Remove 2 screws. Step 2 Remove 3 screws. Step 5 Press down the catches one by one. Caution: To avoid shocked by electricity & injured by high temperature. DO NOT TOUCH electrical components when insert hand under the Top Cabinet.
10.4. Disassembly of AC Inlet P.C.B. • Refer to “Disassembly of Top Cabinet”. Step 1 Remove 1 screw. Caution: During assembling, ensure that catches of Top Cabinet is insert into Front Panel properly. Step 2 Twist the Wire Holder. Step 3 Release Red(TL10) & Black(TL20) wires from the Wire Holder.
10.5. Disassembly Optical 10.6. Disassembly of Rear Panel P.C.B. • Refer to “Disassembly of Optical In P.C.B.”. • Refer to “Disassembly of Top Cabinet”. Step 1 Lift up the Wire Clamper. Step 2 Detach the fan unit connector (CN5401) on D-Amp Step 1 Remove 2 screws.
10.7. Disassembly of Front Panel Step 4 Release 3 tabs. Caution: Do not exert strong force when releasing the tabs. Block Assembly • Refer to “Disassembly of Top Cabinet”. Step 1 Detach 15P FFC at the connector (CN1101) on Main P.C.B..
10.8. Dissassembly of Panel P.C.B. • Refer to “Disassembly of Front Panel Block Assembly”. Step 1 Remove 5 screws. • Assembly of Panel P.C.B Step 1 Solder the 4P cable to the connector (CN6001) on Panel P.C.B.. Step 2 Release 1 catch. Step 2 Place the Panel P.C.B.
Step 4 Dress 4P cable into the Front Panel’s ribs according to diagram shown. Step 2 Lift up the Power Button P.C.B.. Step 5 Fix 5 screws. Step 3 Desolder the 4P Cable (H6803) on Power Button P.C.B.. Step 4 Remove Power Button P.C.B.. 10.9.
Page 49
Step 2 Fix the Power Button P.C.B. onto the Front Panel. Caution: Ensure that it is properly located & seated prop- erly. Step 5 Dress 4P cable into Front Panel’s ribs & screw Boss according to diagram shown. Step 3 Fix 1 screw. Step 4 Dress 4P cable in between Front Panel’s ribs as shown.
10.10. Replacement of Cradle Lid • Refer to “Disassembly of Front Panel Block Assembly”. 10.10.1. Disassembly of Cradle Lid Step 1 Release the Cradle Lid Spring by using a flat head screw driver in the direction of arrow. Step 4 Rotate the Cradle Lid about 45° according to the dia- gram shown.
10.10.2. Assembly of Cradle Lid Caution: During assembling, replace Cradle Lid Damper if broken. Ensure it is properly pasted & fully pressed onto Cradle Lid. Step 1 Insert the Cradle Lid (Shaft A) into the Front Panel (Slot A & hole B). Step 4 Fix the Cradle Lid Spring onto Cradle Lid’s Shaft A.
Page 52
iPhone P.C.B.. Step 2 Remove 1 screw. Step 3 Open the Front Lid Unit. Step 4 Open the Cradle Lid. Step 7 Remove iPod Cradle Assembly. Step 5 Lift up the iPod Cradle Assembly on both sides. • Assembly of iPod Cradle Assembly Step 1 Fix the iPod Cradle Assembly to Front Panel.
Step 2 Press the iPod Cradle Assembly downwards. Note: A “click” sound can be heard when the iPod Cradle Assembly is fixed onto the Front Panel properly. 10.12. Disassembly of iPod/iPhone P.C.B. • Refer to “Disassembly of iPod Cradle Assembly”. Step 1 Remove 2 screws.
Caution: During assembling, ensure that iPod/iPhone P.C.B. is seated properly at the locators. 10.13. Replacement of DVD Lid Unit Step 3 Lift the DVD Lid Spring at Shaft A in the direction of arrow. • Refer to “Disassembly of Front Panel Block Assembly”. 10.13.1.
Page 55
Step 6 Move the DVD Lid Unit to remove from Front Panel. Step 3 Insert the DVD Lid Unit (Shaft B) into the Front Panel (Slot B) as arrow shown. 10.13.2. Assembly of DVD Lid Unit Step 1 Insert the DVD Lid Unit into the Front Panel as arrow shown.
Caution: Ensure that the Shaft B of DVD Lid Unit is fully Step 4 Remove Front Shield Plate Unit. inserted into Slot B of Front Panel. 10.14. Disassembly of Front Shield Plate Unit • Refer to “Disassembly of Front Panel Block Assembly”. Caution: During assembling, ensure that Front Shield is properly inserted &...
Caution: During assembling, ensure that screwing sequence is strictly followed to illustration shown. 10.15. Disassembly of BD Drive • Refer to “Disassembly of Top Cabinet Assembly”. • Refer to “Disassembly of Front Panel Block Assembly”. • Refer to “Disassembly of Front Shield Plate Unit”. Caution: Pairing of BD Drive and Main P.C.B.
Page 58
10.15.1. Replacement of Upper Base Ass’y • Refer to “Disassembly of BD Drive”. Step 1 Remove the 4 screws, and push the Hook in. Step 2 Pull the Tray to the direction of arrow until it can be. Step 2 Lift up the Upper Base Ass’y, and pull it out to the direc- tion of arrow.
Page 59
10.15.4. Replacement Slide Cam • Refer to “Disassembly of BD Drive”. • Refer to “Disassembly of Upper Base Assembly”. • Refer to “Disassembly of Tray”. • Refer to “Disassembly of Pulley Gear & Belt”. Step 1 Remove the Sheet. Step 2 Disconnect the 3 FFCs. Step 3 Remove the 2 Screws and the Angle.
Page 60
10.15.5. Replacement of Mid Base, Driver Gear and Loading Motor • Refer to “Disassembly of BD Drive”. • Refer to “Disassembly of Upper Base Assembly”. • Refer to “Disassembly of Tray”. • Refer to “Disassembly of Pulley Gear & Belt”. •...
10.16. Disassembly of Main P.C.B. Caution: During assembling, ensure that 10P cable is prop- erly bend down onto Main P.C.B. Shield Plate according to • Refer to “Disassembly of Top Cabinet Assembly”. diagram shown. • Refer to “Disassembly of Front Panel Block Assembly”. •...
Caution: During assembling, ensure that Main P.C.B. is seated properly at the locators. Step 12 Lift up to remove Main P.C.B.. 10.17. Disassembly of D-Amp P.C.B. • Refer to “Disassembly of Top Cabinet Assembly”. • Refer to “Disassembly of AC Inlet Assembly”. Step 1 Lift Up 2 Wire Clampers.
Page 65
Step 8 Remove D-Amp P.C.B. according to direction of arrow shown. Step 5 Remove 2 screws on D-Amp P.C.B.. Caution: During assembling, ensure that D-Amp P.C.B. is seated properly at the locators. Step 6 Remove 4 screws. Step 7 Release the tab of the side of the Rear Panel in the direction of arrow.
10.18. Replacement of Digital Ampli- fier IC (IC5100/IC5200) • Refer to “Disassembly of D-Amp P.C.B.”. 10.18.1. Disassembly of Digital Amplifier IC (IC5100/IC5200) Step 1 Place the D-Amp P.C.B. on an insulated material. Step 2 Remove 3 screws. 10.18.2. Assembly of Digital Amplifier IC (IC5100/IC5200) Step 1 Mount the Digital Amplifier IC (IC5100) onto the D-Amp P.C.B..
Caution: During assembling, ensure that heatsink spacer Caution: During assembling, ensure that Power P.C.B. is is seated properly onto Amp Heatsink. properly inserted & fully connected to SMPS P.C.B.. Caution: Ensure that D-Amp P.C.B. is properly located and fixed on to Amp Heatsink before screwing. Step 5 Fix 3 screws.
Page 68
Caution: Do not exert strong force when releasing the tabs. Caution: During assembling, ensure that 10P cable is bend down properly as diagram shown. Step 3 Detach the Front Panel Block Assembly slightly forward. Step 7 Remove 5 screws. Step 4 Lift up the Wire Clampers. Step 5 Detach 6P Cable at the connector (CN5400) on D-Amp P.C.B..
Caution: During releasing P.C.B. Spacer, as it may lead to electric shock or injuries due to high temperature avoid touching surrounding electrical parts. 10.21. Replacement of Switching Reg- ulator IC (IC5701) Step 9 Lift up SMPS P.C.B.. • Refer to “Disassembly of SMPS P.C.B.”. 10.21.1.
Step 2 Remove 1 screw from the Switching Regulator IC Caution: Ensure pins of the Switching Regulator IC (IC5701) are properly seated and soldered on SMPS P.C.B.. (IC5701). Step 3 Remove the Switching Regulator IC (IC5701). Caution: Avoid touching the Heatsink Unit B due to its high temperature after prolonged use.
Page 71
10.22.2. Assembly Rectifier Diode (D5702) Step 1 Apply grease to the Heatsink Unit B. Step 2 Fix and screw the Rectifier Diode (D5702) to the Heat- sink Unit B. Caution: Ensure the Rectifier Diode (D5702) is tightly screwed to the Heatsink Unit B. Step 3 Fix the Heatsink Unit B with Rectifier Diode (D5702) onto SMPS P.C.B..
Caution: Ensure pins of the Rectifier Diode (D5702) are properly seated before soldered onto SMPS P.C.B.. Step 2 Remove 1 screw from the Regulator Diode (D5802). Step 3 Remove the Regulator Diode (D5802) from the SMPS P.C.B.. Caution: Avoid touching the Heatsink Unit A due to its high temperature after prolonged use.
Caution: Ensure the Regulator Diode (D5802) is tightly screwed to the Heatsink Unit A. Step 4 Solder pins of the Regulator Diode (D5802) on the sol- der side of SMPS P.C.B.. Caution: Ensure pins of the Regulator Diode (D5802) are properly seated before soldered onto SMPS P.C.B..
Caution: Ensure the Regulator Diode (D5803) is tightly screwed to the Heatsink Unit A. Step 4 Solder pins of the Regulator Diode (D5803) on the sol- der side of SMPS P.C.B.. Caution: Ensure pins of the Regulator Diode (D5803) are Step 3 Remove 2 screws.
Page 75
Caution: During assembling, ensure Fan Unit is properly Caution: During assembling, ensure that 3P Wire is posi- located & fully catched onto Rear Panel. tioned as diagram shown. Step 5 Remove 2 screws. Step 6 Lift up to remove Fan.
11 Service Position Note: For description of the disassembly procedures, see the Section 10. 11.1. Checking & Repairing Side B of Main P.C.B. Caution: Pairing of BD Drive and Main P.C.B. as “BD Drive & Main P.C.B. Assembly” have to be replaced together. If either BD Drive or Main P.C.B.
Page 77
Step 5 Lift up Panel P.C.B.. Step 8 Remove Front Shield plate Unit. Step 9 Remove Main P.C.B. Shield Plate. Step 10 Connect 45P FFC at the connector (P55001) on Main P.C.B.. Step 11 Connect 18P FFC at the connector (P55002) on Main P.C.B..
Caution: Insulated material is required to insulate Main P.C.B. from other parts. 11.3. Checking & Repairing D-Amp P.C.B. Step 15 Position Panel P.C.B. & Power Button P.C.B. as dia- gram shown. 11.3.1. Checking & Repairing of Side B of Step 16 Connect 22P FFC at the connector (CN2002) on Main P.C.B..
Page 79
Step 4 Twist the Wire Clamper to release 6P Cable. Step 5 Remove 2 screws. Step 9 Twist the Wire Holder. Step 10 Release Red(TL10) & Black(TL20) wires from the Wire Holder. Step 11 Remove AC Inlet P.C.B.. Step 6 Remove 6 screws. Step 7 Remove Fan Unit according to arrow shown.
Step 4 Slightly move Front Panel Block Assembly forward. 11.4. Checking & Repairing SMPS P.C.B. Step 1 Remove Top Cabinet. Step 2 Release the 3 tabs. Step 5 Remove 1 screw. Step 3 Release the 2 tabs at each side of the Front Panel Block Step 6 Twist the Wire Holder.
Page 81
Caution: During releasing of the P.C.B. Spacer, avoid touching the electrical components. Step 11 Release P.C.B. Spacer by using long nose plier. Step 9 Twist the Wire Clampers to release 6P cable (SMPS P.C.B. to D-Amp P.C.B.) & 10P cable (SMPS P.C.B. to Main P.C.B.).
REF NO. MODE CD PLAY STANDBY REF NO. IC2201 MODE CD PLAY -6.8 STANDBY -6.8 IC2202 REF NO. MODE CD PLAY -6.8 STANDBY -6.8 REF NO. IC2300 MODE CD PLAY STANDBY IC2300 REF NO. MODE CD PLAY STANDBY SA-BT235P MAIN P.C.B.
IC2400 REF NO. MODE CD PLAY STANDBY IC2800 REF NO. MODE CD PLAY -6.8 STANDBY -6.8 IC2952 REF NO. MODE CD PLAY STANDBY IC7002 REF NO. MODE CD PLAY STANDBY REF NO. IC7003 MODE CD PLAY STANDBY SA-BT235P MAIN P.C.B.
CD PLAY STANDBY REF NO. IC5400 MODE CD PLAY 13.1 13.1 11.6 STANDBY 13.1 13.1 11.6 IC5401 REF NO. MODE CD PLAY STANDBY IC5402 REF NO. MODE CD PLAY STANDBY IC5404 REF NO. MODE CD PLAY STANDBY SA-BT235P D-AMP P.C.B.
MAIN(SYSTEM CONTROL) Q2805 OPTICAL 1 CN4002 CN2011 OPT IN1 OPT IN 3 SEL B SEL B INVERTER 9 B (MSB) DIGITAL AUDIO IN JK3101 OPTICAL 2 OPT IN2 CN4002 CN2011 OPT IN 3 OPTICAL IN P.C.B. SA-BT235P MAIN(AUDIO) (1/2) BLOCK DIAGRAM...
Q5408, Q5409, Q5414 Q5400,Q5401 Q5402,Q5403 Q5404,Q5405 FAN DC OUT CN5401 FAN CONTROL CN2006 CN5402 FAN SIGNAL CIRCUIT CN5401 FAN LOCK FROM/TO MAIN(SYSTEM CONTROL) QR5401 DC DETECT CN2006 CN5402 ECO CIRCUIT FROM POWER SUPPLY DCDET (MAIN SECTION) SA-BT235P DIGITAL AUDIO BLOCK DIAGRAM...
(SIDE B) FRONT (SIDE B) DOCK FOR iPod/iPhone SPEAKERS DIGITAL AUDIO IN CENTER POWER BUTTON P.C.B. CN1001 OPTICAL 1 OPTICAL 2 (SOLDER SIDE) SUBWOOFER H6803 CN1002 CN4002 JK3100 JK3101 NOTE: " * " REF IS FOR INDICATION ONLY. SA-BT235P WIRING CONNECTION...
16 Schematic Diagram Notes • This schematic diagram may be modified at any time with the development of new technology. Notes: S6002: Stop switch ( S6003: Play switch ( S6005: Vol (+). S6006: Vol (-). S6007: Selector switch. S6801: Power switch ( S6807: Open/Close switch ( •...
DAP_SCL_2 FRONT L - RESERVED DAP_LRCLK DAP_SCLK FRONT L + TO SPEAKERS LRCLK SCLK FRONT R - FRONT R + CENTER - CENTER + SUBWOOFER - SUBWOOFER + IC5405 C0JBAA000501 AND GATE VALID1 TO D-AMP SECTION (3/4) SA-BT235P D-AMP CIRCUIT...
L6806 DGND PANEL CIRCUIT L6804 SMPS CIRCUIT KEY1_BTN AC IN (CN6001) IN SCHEMATIC L6805 120V 60Hz IN SCHEMATIC L6803 DIAGRAM - 31 LED VREF DIAGRAM - 25 TL20* D6800 (BLK) B3ABA0000187 SA-BT235P POWER / POWER BUTTON / AC INLET CIRCUIT...
R1011 IN - L DOCK_R OUT J0JFC0000006 L1030 IN - R iPod DET R1001 R1003 R1004 OUT_L L1032 VGND 100K 100K J0JBC0000015 R1002 OUT_R VIDEO AUDIO_RETURN VGND L1009 iPod_DET L1031 R1012 J0JFC0000006 L1008 J0JFC0000006 SA-BT235P iPod/iPhone / OPTICAL IN CIRCUIT...
AC INLET P.C.B. (REPX0803K) 0653AD 0653AD P5701 L6806 D6800 H6803 S6801 (POWER) AC IN 120V 60Hz TL10* TL20* 0662AC-1 0662AC-1 NOTE: " * " REF IS FOR INDICATION ONLY. SA-BT235P PANEL / POWER / POWER BUTTON / AC INLET P.C.B.
0634A-1 0634A-1 0634A-1 0634A-1 L1025 L1024 (SIDE A) (SIDE B) OPTICAL IN P.C.B. (REPX0793BB) DIGITAL AUDIO IN OPTICAL 1 OPTICAL 2 C3104 C3103 CN4002 JK3100 JK3101 0660AB-3 0660AB-3 0660AB-3 0660AB-3 (SIDE A) (SIDE B) SA-BT235P iPod/iPhone / OPTICAL IN P.C.B.
19 Terminal Function of ICs 19.1. IC6001(C0HBB0000057): IC FL Driver Terminal Name Function LED1 O No Connection LED2 No Connection LED3 No Connection LED4 No Connection Oscillator Input DOUT No Connection Data Input Clock Input Serial Interface Strobe 10 K1 No Connection 11 K2 No Connection...
Page 131
20.1.3. Packaging ACCESSORIES BOX REMOTE CONTROL AC CORD A1-1 R/C BATTERY COVER FM INDOOR ANTENNA VIDEO CABLE SCREW SA-BT235P SB-BT235P F R O N T POLYFOAM (LEFT) POLYFOAM (RIGHT) SC-BT235P-K PACKAGING DRAWINGS...
Page 133
20.1.4. Mechanical Replacement Part List Safety Ref. Part No. Part Name & Qty Remarks Description Safety Ref. Part No. Part Name & Qty Remarks RSC0854 RADIATOR SHEET B Description RSC0927-1 MAIN PCB SHIELD CABINET RXQX1026 CABINET CHASSIS INSULATOR SHEET L6FAYYYH0079 FAN UNIT RXK0625-1 CHASSIS UNIT...
Page 134
Safety Ref. Part No. Part Name & Qty Remarks Description REEX1114 (iPod- MAIN) REZ2014 (OPTI- CAL IN-MAIN)) RXQ1863-1 FRONT SHIELD UNIT RSQ0111 TOP GASKET RSQ0112 GASKET RMA2265 GASKET HOLDER RMN0941 AC INLET HOLDER VQL1V70-J LASER CAUTION LABEL VMA0V86 YOKE VMD5751 UPPER BASE VMD5752 CLAMPER...
20.2. Electrical Replacement Part List Safety Ref. Part No. Part Name & Qty Remarks Description Safety Ref. Part No. Part Name & Qty Remarks IC5404 C0JBAB000837 Description IC5405 C0JBAA000501 PRINTED CIRCUIT IC5701 C5HACYY00004 BOARDS IC5799 MIP2F20MSSCF PCB1 RFKNBT235PA BD DRIVE / MAIN IC5801 C0DABFC00002 P.C.B.
Page 136
Safety Ref. Part No. Part Name & Qty Remarks Safety Ref. Part No. Part Name & Qty Remarks Description Description Q6100 B1BABK000001 TRANSISTOR D5803 B0HFRJ000012 DIODE Q6800 B1ABEB000002 TRANSISTOR D5805 B0EAMM000057 DIODE Q7004 B1ADNB000003 TRANSISTOR D5810 B0ACCK000005 DIODE Q7005 B1ADCE000012 TRANSISTOR D5811 B0BC5R1A0266...
Page 137
Safety Ref. Part No. Part Name & Qty Remarks Safety Ref. Part No. Part Name & Qty Remarks Description Description L1011 J0JFC0000006 INDUCTOR LB57000 J0JGC0000020 INDUCTOR L1032 J0JBC0000015 INDUCTOR L2072 G1C100M00049 INDUCTOR TRANSFORMER L2902 G0A200D00002 CHOKE COIL T5701 ETS42BM1GGAC TRANSFORMER L2903 G0A330ZA0045 CHOKE COIL...
Page 138
Safety Ref. Part No. Part Name & Qty Remarks Safety Ref. Part No. Part Name & Qty Remarks Description Description L1027 D0GBR00JA008 1/16W R1109 D0GA472JA023 4.7K 1/16W L1028 D0GBR00JA008 1/16W R1110 D0GA104JA023 100K 1/16W L1029 D0GBR00JA008 1/16W R1111 ERJ2GEJ750X 1/16W L1030 D0GBR00JA008 1/16W...
Page 139
Safety Ref. Part No. Part Name & Qty Remarks Safety Ref. Part No. Part Name & Qty Remarks Description Description R2210 D0GA101JA023 1/16W R2817 D0GA102JA023 1/16W R2211 D0GA103JA023 1/16W R2821 D0GA473JA023 1/16W R2212 D0GA103JA023 1/16W R2822 D0GA473JA023 1/16W R2213 D0GA102JA023 1/16W R2823 D0GA102JA023...
Page 140
Safety Ref. Part No. Part Name & Qty Remarks Safety Ref. Part No. Part Name & Qty Remarks Description Description R5217 D0GB104JA008 100K 1/16W R5726 ERJ1TRSJR15U 0.15 1/2W R5219 D0GB104JA008 100K 1/16W R5727 ERJ1TRSJR15U 0.15 1/2W R5220 D0GB104JA008 100K 1/16W R5728 D0GB223JA008 1/16W...
Page 141
Safety Ref. Part No. Part Name & Qty Remarks Safety Ref. Part No. Part Name & Qty Remarks Description Description R7009 D0GB272JA008 2.7K 1/16W C2052 F1G1C1030007 0.01uF R7010 D0GB471JA008 1/16W C2053 F1G1E1020001 1000pF R7011 D0GB472JA008 4.7K 1/16W C2054 F2G0J101A083 100uF 6.3V R7012 D0GB272JA008...
Page 142
Safety Ref. Part No. Part Name & Qty Remarks Safety Ref. Part No. Part Name & Qty Remarks Description Description C2962 F1H1H103A219 0.01uF C5217 F2A1J3310032 330uF C2963 F1H1H681A013 680pF C5218 F1J2A333A024 0.033uF 100V C2964 F1H1H104A013 0.1uF C5219 F1H1H104A013 0.1uF C2966 F1J1V1050001 C5222 ECQV1H474JL3...