Table of Contents
Advertisement
Quick Links
For KB version
1. Removing the Rear display filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Replacing the Rear display filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3. Removing the Top cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4. Replacing the Top cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5. Removing the power supply unit and AC cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
6. Replacing the power supply unit and AC cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
7. Removing the LCD unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
8. Replacing the LCD unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
9. Replacing the FDD unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
10. Removing the FDD unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
11. D-RAM disk: S.O. DIMM (Locally supplied) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
12. MCR unit: UP-E12MR2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
13. Adjusting the IRQ10/11 on the ISA PWB.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
14. RS232 & CENTRO I/F: ER-A8RS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
15. Rear display UP-I20DP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
16. Pole display: UP-P20DP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
17. Drawer unit: ER-03DW/04DW/05DW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
18. COM1, COM2, COM3/5, and COM4/6 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
19. Built-in printer: UP-T80BP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
20. Key pad : UP-C30PK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Parts marked with "
" is important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
For TQ,TS,KA version
CONTENTS
SHARP CORPORATION
POS TERMINAL
UP-5350
MODEL
("V" version)
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
Advertisement
Table of Contents
Related Manuals for Sharp UP-5350
Summary of Contents for Sharp UP-5350
-
Page 1: Table Of Contents
POS TERMINAL UP-5350 MODEL For TQ,TS,KA version ("V" version) For KB version CONTENTS 1. Removing the Rear display filter ..........1 2. -
Page 2: Removing The Rear Display Filter
Precautions Before installation, be sure to turn off the power. Use gloves to protect your hand from being cut by the angle and the chassis. Connect all the cables securely. When connecting or disconnecting the cables, be careful not to apply stress to the cables. -
Page 3: Removing The Power Supply Unit And Ac Cord
5. Removing the power supply unit 7. Removing the LCD unit and AC cord 1) Remove the LCD unit a) Remove the screw 1) Remove the two screws b) Remove the tilt cover 2) Remove the AC cord cover c) Remove the core 3) Use a minus screwdriver to loosen the AC cord fixing screws (2 d) Remove the three Screws... -
Page 4: Replacing The Lcd Unit
3) Remove the Inverter PWB 5) Remove the LCD a) Remove the Inverter cable a) Remove the six screws b) Remove the CCFT cable b) Remove the four screws c) Remove the screw c) Remove the LCD plate d) Remove the Inverter cover d) Remove the LCD PWB unit e) Remove the screw and LED PWB... -
Page 5: Replacing The Fdd Unit
7) Install the FDD UNIT to the UP-5350. 8. Replacing the LCD unit a) Install the FDD UNIT and FDD ANGLE-B to the bottom cabinet with the four screws Install the LCD unit in the reverse order of removing. b) Connect the FDD CABLE to the Main PWB. -
Page 6: Removing The Fdd Unit
17 18 11. D-RAM disk: S.O. DIMM (Locally supplied) [Device] 144 pin Small Outline DIMM (8Mbytes/16Mbytes/32Mbytes/64Mbytes) [Outline] UP-5350 has a socket as Small Outline DIMM. It is necessary to satisfy with S.O.DIMM memory specification as follows. [Specification] 144pin S.O.DIMM 8Mbytes... -
Page 7: Mcr Unit: Up-E12Mr2
3) Remove the option D-RAM disk. 14. RS232 & CENTRO I/F: ER-A8RS a) Open the arms of D-RAM connector right and left. b) The D-RAM disk will be lifted automatically. ER-A8RS connection MCR UNIT: UP-E12MR2 1) Fix the MCR ANGLE to the lower cabinet with two screws 2) Connect the MCR cable to the MCR connector with the cable... -
Page 8: Rear Display Up-I20Dp
Align threaded holes completely before securing the I/F PWB with 3) Connect the display cable to the connector: CN: 1 on the Main screws. 4) Install the Display unit to the cabinet a) Align the positioning boss of the bottom cabinet with the angle hole in the display unit. - Page 9 How to Extend Display Pole 5) Remove the two screws 6) Remove the Base cabinet from the pole cabinet The pole can be extended by installing the attached pole to the standard pole. COMPONENT LIST: NAME Q’ty Pole cabinet Pole extension Screw (M3 Pole connection Securing the UP-P20DP to...
-
Page 10: Drawer Unit: Er-03Dw/04Dw/05Dw
10) Install the attached pole cabinet to the pole cabinet to fix it Lowering the height of the UP-P20DP with the screw Remove the standard Pole and attach the Base cabinet to the Ratch . At this time, replace the standard Display cable and the Earth wire with the S type cable and wire Display cable... -
Page 11: Com1, Com2, Com3/5, And Com4/6 Connector
Main PWB 18. COM1, COM2, COM3/5, and COM4/6 Connector 1) COM1 & COM2 D-SUB 9pin Connector CI signal of COM1 or COM2 and +5V power supply can be switched in order to supply +5V power. Connector Specifications* D-SUB9 Pin No. Signal Function S2 = COM1:... -
Page 12: Built-In Printer: Up-T80Bp
PS+CONTROL PWB . (No. CN1) Send Data Connect the I/F CABLE of the PS+CONTROL Signal Ground — to the UP-5350 MAIN PWB (No.CN109) Signal Ground — Receive Data Data set Ready Clear to Send 19. Built-in printer: UP-T80BP Remove the BOTTOM PLATE... - Page 13 Remove the PRINTER LID Install the AUTO CUTTER RELAY PWB UNIT a) Remove the screw a) Install the AUTO CUTTER RELAY PWB UNIT with SCREW b) Remove the PRINTER LID Install the PAPER ROLLERs (4ea.) b) Pass the AUTO CUTTER RELAY PWB CABLE through the hole (C).
- Page 14 Install the PRINTER UNIT Wiring for each cables as shown below a) Connect the AUTO CUTTER CABLE to the AUTO CUTTER RELAY PWB b) Pass the HEAD CABLE through the hole (C). c) Pass the MOTOR CABLE and SENSOR CABLE through the hole (D).
- Page 15 Wiring for each cables as shown below a) Attach the FERRITE CORE (S size) to the I/F CABLE b) Fix the I/F CABLE and EARTH WIRE with the CABLE BAND c) Set the switch: SW2 to the "MRS" position. Fig. 9 Install the BOTTOM PLATE Install the PRINTER COVER Fig.
-
Page 16: Key Pad: Up-C30Pk
1. LIST FOR SCREWs 20. KEY PAD: UP-C30PK L [mm] PARTS CODE M [mm] Opetion for KB. Standard for TQ, TS, KA XEBSD30P08000 1) Remove the upper cabinet. 2) Remove the keyboard lid from the upper cabinet. XEBSD26P06000 XEBSD26P08000 XHBSD30P06000 Keyboard is tightly engaged and hard to be removed. - Page 17 3) Attach the keyboard cover and keyboard unit to theupper 4) How to wire cables: cabinet, and fix them with four screws . Run the cable along the mark-off line of the cabinet and secure it at three points with filament tape. However, remember that on products that will be manufactured in June 2000 and after, the cable will be secured with clamps.
- Page 18 COPYRIGHT 2000 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted. In any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.