Page 1
HP Director Blade Installation Instructions Overview Use these installation instructions if you have purchased one of the optional director blades listed in Table 1 (page 1). Install the blades in compatible director models only. NOTE: This document refers to blades by their short names.
HP DC SAN FC8-64 BK798A DC SAN Backbone Director Director, BK798B 64-port 8Gb DC04 SAN Director, Fibre Channel SN8000B 8-Slot SAN Blade Backbone Director, SN8000B 4-Slot SAN Director HP SAN FC10-6 AK86 1A 4/256 SAN Director, Director AK861B DC SAN Backbone...
Page 3
FC8-48E components FC16-32 components Figure 2 FC8-48E Figure 3 FC16-32 1. Power LED 2. Status LED 1. Power LED 2. FC ports 8–15 3. FC ports 24–47 4. FC ports 0–23 3. FC ports 0–7 4. Port status LED 5. FC ports 24–31 6.
FC16-48 components FCOE10-24 components Figure 4 FC16-48 Figure 5 FCOE10-24 1. Power LED 2. 10-GbE FCoE ports 0–1 1 3. Status LED 4. 10-GbE FCoE ports 12–23 1. Power LED 2. FC ports 0–23 3. Status LED 4. FC ports 24–47 Page 4...
Page 5
FX8-24 components FS8- 1 8 components Figure 6 FX8-24 Figure 7 FS8-18 1. Power LED 2. 1 GbE ports 0–3 3. 10-GbE ports 0–1 4. FC ports 0–5 5. Status LED 6. 1 GbE ports 4–9 7. FC ports 6–1 1 1.
Page 6
FC4- 1 6 components FC4-32 components Figure 8 FC4-16 Figure 9 FC4-32 1. Power LED 2. Status LED 1. Power LED 2. Status LED 3. FC Port 4. Port speed LED 3. FC Port 4. Port speed LED (left port) 5.
Page 7
FC4-48 components FC8- 1 6 components Figure 10 FC4-48 Figure 1 1 FC8-16 1. Power LED 2. Status LED 3. FC Port 4. Port status LED 5. FC ports 0–15 1. Power LED 2. Status LED 3. FC Port 4. Port status LED 5.
Page 8
FC8-32 components FC8-48 components Figure 12 FC8-32 Figure 13 FC8-48 1. Power LED 2. Status LED 1. Power LED 2. Status LED 3. FC Port 4. Port status LED 3. FC Port 4. Port status LED 5. FC ports 16–31 6.
Page 9
FC8-64 components FC10-6 components Figure 14 FC8-64 Figure 15 FC10-6 1. Power LED 2. Status LED 3. FC port 4. Port status LED 5. FC ports 0–5 1. Status LED 2. Power LED 3. FC Port 4. Port status LED 5.
Page 10
FC4- 1 6IP components FR4- 1 8i components Figure 16 FC4-16IP Figure 17 FR4-18i blade 1. Power LED 2. Status LED 3. FC Port 4. Port status LED 5. GbE ports 0–1 6. FC ports 0–15 1. Power LED 2. Status LED 3.
CR16-8 and CR16-4 use QSFP transceivers for ICL connections. For more information about supported transceivers, see the HP SPOCK website at http://www.hp.com/ storage/spock. You must sign up for an HP Passport to gain access. For information on SAN compatibility, see http:// 1. Filler panel with handle 2.
Locate an appropriate slot. Slots are numbered from left to right when facing the port side of the chassis. For the HP 4/256 SAN Director: Install the blades in slots 1 through 4 and 7 through 10. 1. 4/256 SAN Director 2.
HP B-series SN8000B 8-Slot SAN Backbone upper and lower rail guides in the slot. Director Switch Hardware Reference Guide Slide the blade into the slot until it is firmly HP HP B-series SN8000B 4-Slot SAN Director seated (Figure 20 (page 13)).