1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Fax Machine
  5. UX-460
  6. Service manual

Sharp UX-460 Service Manual

Hide thumbs Also See for UX-460:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual
Thank You For
Purchasing This DVD
Collection! If You Did
NOT Purchase This
Document As Part Of A
DVD Collection From
RushAZ85705 on E-Bay,
This Document Has
Been Passed
Fraudulently! Please
Alert
RushTalion@Cox.Net
!
Thank You Again!

Advertisement

Table of Contents
loading

Related Manuals for Sharp UX-460

Summary of Contents for Sharp UX-460

  • Page 1 Thank You For Purchasing This DVD Collection! If You Did NOT Purchase This Document As Part Of A DVD Collection From RushAZ85705 on E-Bay, This Document Has Been Passed Fraudulently! Please Alert RushTalion@Cox.Net Thank You Again!

  • Page 2: Table Of Contents

    UX-460U SERVICE MANUAL No. 00ZUX460U/SME FACSIMILE UX-300 UX-460 MODEL This service manual UX-460U is to appear only on the place where it is changed from UX-300U/FO-760U, and refer to a service manual UX-300U/FO-760U (00ZUX300U/SME) except for it. CONTENTS CHAPTER 1. GENERAL DESCRIPTION CHAPTER 5.
  • Page 3 UX-460U CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer.

  • Page 4: Chapter 1. General Description

    (140 to 600 mm) As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for procduct improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some deviation from these values in individual units.

  • Page 5: Operation Panel

    UX-460U [2] Operation panel 6 7 8 TEL FAX ANSWERING DIGITAL SYSTEM SPEED REPEAT REC/MEMO PLAY/SKIP RECEPTION VOLUME DIAL MODE DOWN RESOLUTION FUNCTION REDIAL DELETE HOLD/ PQRS WXYZ COPY/HELP SEARCH STOP 05/POLL SPEAKER START/MEMORY 17 18 11. Number keys 1. SPEED DIAL key Use these keys to dial numbers, and enter numbers and Press this key to dial a 2-digit Speed Dial number.

  • Page 6: Chapter 2. Adjustments

    UX-460U (1) FU100 (ICP-S07) is installed in order to protect IC’s from an over- CHAPTER 2. ADJUSTMENTS current generated in the motor drive circuit. If FU100 is open, replace it with a new one. [1] Adjustments 3. Settings (1) Dial mode selector General DIAL mode (Soft Switch No.

  • Page 7: Diagnostics And Service Soft Switch

    UX-460U [2] Diagnostics and service soft switch 1. Operating procedure (1) Entering the diagnostic mode Press FUNC → 9 → → 8 → # → 7 , and the following display will appear. ROM Ver. FKQ0 After 2 sec: DIAG MODE FKQ0 Then press the START key.
  • Page 8 UX-460U 3. Diagnostic items description 3. 6. Signal send mode 3. 1. Soft switch mode This mode is used to send various signals to the circuit during FAX com- munication. Every push of START key sends a signal in the following Used to change the soft switch settings.

  • Page 9: Ux-460U

    UX-460U 3. 12. Entry data receive 3. 13. Flash memory check In this mode, the registered data sent from the other machine is receiv- Data is written into and read from the flash memory to check the data ed and the received data is registered in the machine. When this mode conformity.

  • Page 10: Reserved

    UX-460U 5. Soft switch description • Soft switch Switch setting and function Initial DATA ITEM Remarks setting Protect from echo Forced 4800 BPS reception Footer print Length limitation of copy/send/receive No limit Copy/send: 1m Receive: 1.5m CSI transmission No transmitted Transmitted DIS receive acknowledgement during G3 Twice...

  • Page 11: Ux-460U

    Disconnect the line when DIS is received in RX mode Equalizer freeze control (MODEM) Equalizer freeze control 7200 BPS only CNG transmission in manual TX mode Initial compression scheme for sharp fax in MR mode H2 mode TX mode Reserved...

  • Page 12: Ux-460U

    UX-460U Switch setting and function Initial DATA ITEM Remarks setting DTMF signal transmission level (High) Binary input No. = 16 8 4 2 1 1 2 3 4 5 0 0 1 1 0 Reserved Reserved Reserved Reading slice (Binary) Factory Light Dark...

  • Page 13: Ux-460U

    UX-460U Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved DTMF detection time 50ms 80ms 100ms 120ms No. 1 No. 2 Protection of remote reception (5 ) detect Yes OPTION Remote reception with GE telephone Compatible Not compatible Remote operation code figure by external...

  • Page 14: Ux-460U

    UX-460U Switch setting and function Initial DATA ITEM Remarks setting Busy tone detection ON/OFF time (Lower 350ms 200ms duration) Busy tone detection ON/OFF time (Upper 650ms 900ms duration) Reserved Busy tone continuous sound detect time Busy tone detect continuation sound detect during OGM Busy tone detect continuation sound detect (during ICM: for internal A.M.)

  • Page 15: Ux-460U

    UX-460U Switch setting and function Initial DATA ITEM Remarks setting AGC maximum gain (line) Binary input (10 ~ 25 dB) (1 dB step) No. = AGC maximum gain (Mic) Binary input (10 ~ 25 dB) (1 dB step) No. = AGC eref access code (line) Binary input (-0 ~ -30 dB) (2 dB step)

  • Page 16: Ux-460U

    UX-460U Switch setting and function Initial DATA ITEM Remarks setting Automatic cover sheet OPTION Communication results printout E/T/M Send only Always No print Err only OPTION (Transaction report) No. 2 No. 3 No. 4 Reserved Reserved Reserved Reserved Entering DIAG mode by pressing SPEED Reserved OGM / ICM output level Binary input...

  • Page 17: Ux-460U

    UX-460U • Soft switch function description SW-A2 No. 7 Communication error treatment in RTN sending mode (Reception) SW-A1 No. 1 Protect from echo Used to determine communication error treatment when RTN is sent by occurrence of a received image error in G3 reception. When it is set to Used to protect from echo in reception.

  • Page 18: Ux-460U

    When set to "0", if the other fax is Sharp model, fax transmit the document Set to "0". by H2 mode. When set to "1", even if the other fax is Sharp model, fax SW-B6 No. 1 ~ No. 5 DTMF signal transmission level (High) transmit the document by MR mode.
  • Page 19 UX-460U SW-D1 No. 1 ~ No. 4 Number of rings for auto receive 2S ring When the machine is set in the auto receive mode, the number of rings before answering can be selected. It may be set from one to four rings 4S ring STANDARD using a binary number.

  • Page 20: Ux-460U

    UX-460U SW-F1 No. 1, No. 2 DTMF detect time SW-H1 No. 3 Reserved Used to set detect time of DTMF (Dual Tone Multi Frequency) used in Set to "0". remote reception (5 SW-H1 No. 4 Busy tone continuous sound detect time The longer the detect time is, the less the error detection is caused by Set detecting time busy tone for 5 seconds or as is PTT.

  • Page 21: Ux-460U

    UX-460U SW-I2 No. 6, No. 7 CPC detection time SW-I6 No. 5 ~ No. 8 AGC gain adaptation threshold (Mic) Used to set the CPC (Calling Party Control) signal detect time. The AGC adjusts the amount of gain applied to the incoming message only when the average energy exceeds the AGC Gain Adaptation SW-I2 No.

  • Page 22: Ux-460U

    UX-460U SW-J3 No. 2 ~ No. 4 Communication result printout (Transaction report) Every communication, the result can be output. As usual, it is set to print the timer sending communication error alone. If No. 2: 0 No. 3: 1 No. 4: 0 are set, printing is always on (printed even if it is normally ended).

  • Page 23: Troubleshooting

    UX-460U [3] Troubleshooting Refer to the following actions to troubleshoot any of the problems men- • Apply line equalization SOFT SWITCH A5-1, 2. tioned May be used in case [1] [2] [3] [4]. in 1-4. • Slow down the transmission speed SOFT SWITCH A2-1, 2, 3, [1] A communication error occurs.

  • Page 24: Error Code Table

    UX-460U [4] Error code table 1. Communication error code table G3 Transmission Code Final received signal Error Condition (Receiver side) Incomplete signal frame Cannot recognize bit stream after flag NSF, DIS Cannot recognize DCS signal by echo etc. Cannot recognize NSS signal (FIF code etc) Disconnects line during reception (carrier missing etc) Disconnects line by fall back Disconnects line during reception of multi page...

  • Page 25: Chapter 4. Diagrams

    UX-460U CHAPTER 4. DIAGRAMS 4 – 1...

  • Page 26: Wiring Diagram

    [2] Wiring diagram HANDSET CAM SW TX/RX MOTOR MJTEL TEL LINE MJ1/2 EXTERNAL LINE CNMT CNCSW THERMAL HEAD TEL/LIU PWB UNIT CNTH CNLIUA CNLIU CONTACT IMAGE SENSOR CONTROL PWB UNIT CNCIS CNPW LCD UNIT CNPN CNSP POWER SUPPLY CNLCD PWB UNIT CNPN OPERATION AC CORD...

  • Page 27: Ux-460U

    UX-460U 4 – 3...

  • Page 28: Chapter 5. Circuit Description

    UX-460U 3. Operational description CHAPTER 5. CIRCUIT DESCRIPTION Operational descriptions are given below: • [1] Circuit description Transmission operation When a document is loaded in standby mode, the state of the docu- ment sensor is sensed via the 1 chip fax engine (FC100M). If the 1.

  • Page 29: Circuit Description Of Control Pwb

    UX-460U 3) 27C020 (IC4): pin-32 DIP (ROM) [2] Circuit description of control PWB EPROM of 2Mbit equipped with software for the main CPU. 1. General description 4) W24010S-70LE (IC1): pin-32 SOP (SRAM) Line memory for the main CPU system RAM area and coding/decoding Fig.

  • Page 30: Ux-460U

    UX-460U FC100M (IC8) Terminal descriptions Input Output Pin Description Pin Name Pin No. Type Type (Note: Active low signals have an "n" pin name ending.) CPU Control Interface − MIRQn Modem interrupt, active low. (Hysteresis In, Internal Pullup.) − SYSCLK System clock.

  • Page 31: Ux-460U

    UX-460U FC100M (IC8) Terminal descriptions Input Output Pin Name Pin No. Pin Description Type Type Operator Panel Interface OPI[2]/GPIO[23]/ (Pullup, Hysteresis In) Keyboard return [2] or GPIO[23] or SSCLK1 SSCLK1 (for SSIF1) OPI[3]/GPIO[24] (Pullup, Hysteresis In) Keyboard return [3] or GPIO[24] −...

  • Page 32: Ux-460U

    UX-460U (2) Panel control block The following controls are performed by the FC100M. • Operation panel key scanning • Operation panel LCD display (3) Mechanism/recording control block • Recording control block diagram (1) OPO[7:0]* TEST OPERATOR OPI[3:0]* BATRSTN PANEL, PANEL/LCD PWB LEDCTL* RESETN KEYPAD,...

  • Page 33: Ux-460U

    UX-460U FEATURES (4) Modem (RFX96V24) block • Group 3 facsimile transmission/reception INTRODUCTION The Rockwell RFX96V24 MONOFAX ® facsimile modem family provides – ITU-T V.29, V.27 ter, T.30, V.21 Channel 2, T.4 9600 bps half-duplex capability with options supporting DigiTalk™ voice –...

  • Page 34: Ux-460U

    UX-460U RFX96V24 (IC5) Hardware Interface Signals Pin No. Signal Name I/O Type GP17/RINGD Pin Signals – 100-Pin PQFP GPO7 Pin No. Signal Name I/O Type GPO6 GPO5 GPO4 GPO3 DGND2 VDD1 IRQ1 IA/OB GPO2 IA/OB GPO1 IA/OB GPO0 IA/OB RESET IA/OB XTLI IA/OB...

  • Page 35: Circuit Description Of Tel/Liu Pwb

    UX-460U [3] Circuit description of TEL/LIU PWB (1) TEL/LIU block operational description 1) Block diagram TEL/LIU PWB CONTROL PWB GAIN-C TXCONT TXOUT SIGTX TEL LINE HS DETECTOR MODEM 4053 (RFX96V24) SIGRX CI DETECTOR RXIN HANDSET TELIN TELOUT VOL A VOL B VOL C BZCONT HOOK SW...

  • Page 36: Ux-460U

    UX-460U 5. Externally connected TEL OFF HOOK detection circuit section 4) Signal selection The following signals are used to control the transmission line of TEL/ • The circuit current detection is turned on together with OFF HOOK FAX signal. For details, refer to the signal selector matrix table. of main body or OFF HOOK of externally connected TEL.

  • Page 37: Ux-460U

    UX-460U [Signals for status recognition according to input signals] Signal Name Function H:The handset is in the on-hook state. L: The handset is in the off-hook state. Incoming call (CI) detection signal H:The handset or external telephone is in the on-hook state.

  • Page 38: Circuit Description Of Power Supply Pwb

    UX-460U [4] Circuit description of power supply PWB 1. Block diagram 2.5A/125V Noise Rectifying Filter AC IN Smoothing Switching Circuit Regulator Circuit Circuit Circuit (RCC system) +24V FUSE 4A/72V Photo Coupler Fig. 7 2-1. Noise filter circuit The overcurrent protection is performed by bringing Q1 to OFF state through detection of voltage increase in the auxiliary winding of T1 by The input noise filter section is composed of L and C, which reduces ZD2, R5 and R6.

  • Page 39: Chapter 6. Circuit Schematics And Parts Layout

    UX-460U CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT 19.66MHz BATRST 270 x 4 VBAT C188 2200P RESET (4-2D) PWRDWN C185 22P XOUT 270 x 4 32.768kHz TSTCLK SYSCLK (1-2I) SYSCLK C210 22P MIRQ +VREF R132 (5-1D) (3-3B) +VREF MIRQ R177 –VREF (5-1D) DEBUG...

  • Page 40: Ux-460U

    UX-460U 6 – 2...

  • Page 41: Ux-460U

    UX-460U TRESET 51,91 N.C. N.C. SAICLK 42,49 N.C. N.C. TSTROBE 34,41 N.C. N.C. IAICLK 32,33 N.C. N.C. CLKIN 22,31 N.C. N.C. IACLK TXDAT SR4OUT RXOUT SR3IN DGND4 RMODE DGND3 TMODE 23 L100 SR1IO VDD3 XTLO DGND2 L105 XTLI VDD2 N.C. EYESYNC DGND5 N.C.

  • Page 42: Ux-460U

    UX-460U 6 – 4...

  • Page 43: Ux-460U

    UX-460U C246 C245 C244 C243 6 – 5...

  • Page 44: Ux-460U

    UX-460U 6 – 6...
  • Page 45 UX-460U Control PWB parts layout (Top side) 6 – 7...

  • Page 46: Ux-460U

    UX-460U Control PWB parts layout (Bottom side) 6 – 8...

  • Page 47: Ux-460U

    UX-460U 6 – 9...

  • Page 48: Ux-460U

    UX-460U TEL/LIU PWB parts layout (HOOK-SW) J13(+5V) P-IN 6 – 10...

  • Page 49: Ux-460U

    UX-460U 1SS133 2SC1741AS-Q 6 – 11...

  • Page 50: Ux-460U

    UX-460U Power supply PWB parts layout 6 – 12...

  • Page 51: Operation Panel Pwb Circuit

    [4] Operation panel PWB circuit CNLCD-11 1SS270 SEN0 CNPN-12 FUNC SPEED CNLCD-12 1SS270 SEN1 CNPN-13 DOWN STOP REDAIAL PLAY CNLCD-13 1SS270 SEN2 CNPN-14 RECEPTION COPY HOLD REPEAT CNLCD-14 1SS270 SEN3 CNPN-15 START RESOLUTION SPEAKER DELETE KEN 1A CNPN-4 KEN 2A CNPN-3 KEN 3A CNPN-2...

  • Page 52: Chapter 8. Others

    UX-460U CHAPTER 8. OTHERS [3] Changing the record paper size How to change the A4 size and letter size of the record papers 1) It becomes the record paper of the A4 size by installing A4 guide (PGiDM2535XHSC) which shows in the drawing. Remove A4 guide when you use the record paper of the letter size. RP hopper PGiDM2535XHSC 2) Set soft switch SW-L2 No.1 and the initialization of SW-L2 No.2 as follows.

  • Page 53: Ux-460U

    UX-460U M E M O 8 – 10...
  • Page 54 UX-460U PARTS GUIDE UX-300 UX-460 MODEL CONTENTS Packing material & Accessories Cabinet, etc. Control PWB unit Top cover and sub frame TEL-Liu PWB unit Upper cabinet Power supply PWB unit Document guide upper Index Drive unit Because parts marked with "...

  • Page 55: Cabinet, Etc

    UX-460U [1] Cabinet, etc. TOP COVER/ SUB FRAME B2x2 B2x2 DOCUMENT GUIDE UPPER DRIVE UNIT B2x2 B2x9 – 1 –...

  • Page 56: Ux-460U

    UX-460U PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [1] Cabinet,etc. DCEKP440BXH27 Operation panel unit QCNW-4935XHZZ Panel cable RCORF2124XHZZ Core MLEVP2297XHZZ Cover switch lever MSPRT3069XHFJ Cover switch spring NROLR2375XHZZ Feed roller NSFTP2302XHZZ Feed roller shaft PGIDM2538XHZZ Original paper guide CCNW-4938XH01 Speaker ass’y CGERH2444XHY1 BT gear ass’y...

  • Page 57: Top Cover And Sub Frame

    UX-460U [2] Top cover and sub frame PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [2] Top cover and sub frame GCOVA2403XHSA Top cover JKNBP2091XHZZ Release knob MSPRC2832XHZZ Hopper spring NGERP2318XHZZ Pinion gear PGIDM2533XHSA Hopper guide,left PGIDM2534XHSA Hopper guide,right MSPRD3065XHFJ PO pinch roller spring NROLP2332XHZZ PO pinch roller...

  • Page 58: Upper Cabinet

    UX-460U [3] Upper cabinet B1x5 PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [3] Upper cabinet GCABA2324XHSG Upper cabinet JBTN-2242XHSA 12 key JBTN-2243XHSA Direct key JBTN-2244XHSA Start key JBTN-2245XHSA Stop key JBTN-2246XHSA Mode key DCEKP450BXH05 Operation panel PWB unit QCNW-4935XHZZ Panel cable JBTN-2247XHSA TAD key...

  • Page 59: Document Guide Upper

    UX-460U [4] Document guide upper PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [4] Document guide upper LPLTG2911XHZZ Separator rubber LPLTP2908XHZZ Separator plate MSPRC3071XHFJ Pinch roller spring MSPRP3079XHFJ Paper feed spring MSPRT2951XHZZ Separate spring NBRGP2141XHZZ Transfer bearing NGERH2445XHZZ Back roller gear NROLP2334XHZA Pinch roller NROLP2406XHZZ...

  • Page 60: Drive Unit

    UX-460U [5] Drive unit PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [5] Drive unit CGERH2459XH01 Slip gear ass’y CLEVP2298XH01 Planet gear lever A ass’y CLEVP2299XH01 Planet gear lever B ass’y CLEVP2300XH01 Planet gear lever C ass’y CLEVP2303XH01 Planet gear lever D ass’y LFRM-2200XHZZ Drive unit frame LPLTM2994XHFW...

  • Page 61: Packing Material & Accessories

    UX-460U [6] Packing material & Accessories TAPE TAPE TAPE AC CORD TAPE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [6] Packing material & Accessories SPAKC096BXHZZ Packing case TLABM245AXHZZ Box label TINSE4007XHZZ Operation manual TLABH4751XHZZ Rapid key labels CPLTP3002XHB1 Imaging film cartridge and label ass’y TLABH4752XHZZ Film set label LPLTP3003XHSA...

  • Page 62: Control Pwb Unit

    UX-460U PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [7] Control PWB unit UBATL2064SCZZ Battery(CR2032THG) [BAT1] VCEAGA1HW475M Capacitor(50WV 4.7µF) [C2] VCEAGA1HW106M Capacitor(50WV 10µF) [C3] VCEAGA1HW105M Capacitor(50WV 1µF) [C4] VCEAGA1HW106M Capacitor(50WV 10µF) [C5] VCEAGA1EW476M Capacitor(25WV 47µF) [C6] VCEAGA1HW106M Capacitor(50WV 10µF) [C7] VCEAGA1HW226M Capacitor(50WV 22µF) [C8]...

  • Page 63: Ux-460U

    UX-460U PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [7] Control PWB unit VCKYTV1EB104K Capacitor(25WV 0.1µF) [C201] VCKYTV1HB473K Capacitor(50WV 0.047µF) [C202] VCKYTV1HB222K Capacitor(50WV 2200PF) [C204] VCKYTV1HB103K Capacitor(50WV 0.01µF) [C205] VCKYTV1EB104K Capacitor(25WV 0.1µF) [C207] VCKYTV1HF104Z Capacitor(50WV 0.1µF) [C208] VCKYTV1EB104K Capacitor(25WV 0.1µF) [C209] VCCCTV1HH220J Capacitor(50WV 22PF)

  • Page 64: Ux-460U

    UX-460U PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [7] Control PWB unit Resistor(1/10W 0Ω ±5%) VRS-TS2AD000J [R117] Resistor(1/10W 150Ω ±5%) VRS-TS2AD151J [R118] Resistor(1/10W 150Ω ±5%) VRS-TS2AD151J [R119] Resistor(1/10W 0Ω ±5%) VRS-TS2AD000J [R120] Resistor(1/10W 0Ω ±5%) VRS-TS2AD000J [R121] Resistor(1/10W 270Ω ±5%) VRS-TS2AD271J [R122] Resistor(1/10W 270Ω...

  • Page 65: Tel-Liu Pwb Unit

    UX-460U PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [7] Control PWB unit Resistor(1/10W 270Ω ±5%) VRS-TS2AD271J [R210] Resistor(1/10W 270Ω ±5%) VRS-TS2AD271J [R211] Resistor(1/10W 270Ω ±5%) VRS-TS2AD271J [R212] Resistor(1/10W 5.6KΩ ±5%) VRS-TS2AD562J [R213] Resistor(1/10W 30KΩ ±5%) VRS-TS2AD303J [R214] Resistor(1/10W 33KΩ ±5%) VRS-TS2AD333J [R215] Resistor(1/10W 30KΩ...

  • Page 66: Power Supply Pwb Unit

    UX-460U PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [8] TEL-Liu PWB unit VCKYPA1HB102K Capacitor(50WV 1000PF) [C8] VCEAGA1HW225M Capacitor(50WV 2.2µF) [C9] VCEAGA1HW475M Capacitor(50WV 4.7µF) [C10] VCKYPA1HB102K Capacitor(50WV 1000PF) [C11] VCKYPA1HB102K Capacitor(50WV 1000PF) [C12] VCKYPA1HB221K Capacitor(50WV 220PF) [C13] VCKYPA1HB102K Capacitor(50WV 1000PF) [C14] VCKYPA1HF223Z Capacitor(50WV 0.022µF)

  • Page 67: Ux-460U

    UX-460U I n d e x PRICE PRICE PRICE PART PART PART PARTS CODE PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK RANK MARK RANK MSPRP3054XHFJ 1-24 QCNW-4971XHZZ 1-50 CCNW-4938XH01 MSPRP3055XHFJ 1-25 QJAKZ2069SCBB 8-30 CGERH2444XHY1 1-10 MSPRP3079XHFJ QJAKZ2070SC0D 8-31 CGERH2459XH01 MSPRT2951XHZZ...

  • Page 68: Ux-460U

    UX-460U PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE MARK MARK MARK RANK RANK RANK RANK RANK RANK VCEAGA1HW107M VCKYTV1HB103K 7-55 VRS-TS2AD000J 7-137 ″ ″ VCEAGA1HW225M 7-84 7-139 ″ VCEAGA1HW226M VCKYTV1HB222K 7-12 7-160 ″ ″ ″ 8-17 7-17 7-161...

  • Page 69: Ux-460U

    ″ 7-265 7-257 © COPYRIGHT 1999 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Table of Contents