Advertisement
Quick Links
Advertisement
Related Manuals for Sharp UX-465L
Summary of Contents for Sharp UX-465L
- Page 1 MODEL UX-465L FACSIMILE OPERATION MANUAL 1. Installation 2. Setting Up and Using OpenLCR 3. Using the Answering Machine 4. Sending Documents 5. Receiving Documents 6. Making Copies 7. Making Telephone Calls 8. Special Functions 9. Printing Lists 10. Maintenance 11. Troubleshooting...
- Page 2 In order to program this information into your facsimile machine, please refer to the appropriate instructions in the operation manual." As an NERGY partner, SHARP has determined that this product meets the NERGY guidelines for energy efficiency. FOR YOUR RECORDS Please record the model number and serial number below, for easy reference, in case of loss or theft.
-
Page 3: Introduction
Introduction Welcome, and thank you for choosing a Sharp facsimile machine! The features and specifications of your new Sharp fax are shown below. Automatic dialing Rapid Key Dialing: 4 numbers Speed Dialing: 40 numbers Imaging film Initial starter roll (included with machine): 32 ft. - Page 4 Halftone (grayscale) 64 levels Display 16-digit LCD display Paper tray capacity Letter: 60 sheets Legal: 30 sheets (16- to 20-lb. paper) Compression scheme MR, MH, MMR Applicable telephone line Public switched telephone network Compatibility ITU-T (CCITT) G3 mode Input document size Automatic feeding: Width: 5.8 to 8.5"...
-
Page 5: Important Safety Information
Weight Approx. 7.7 lbs. (3.5 kg) As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. - Page 6 Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Never touch bare telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. Avoid using a telephone (other than a cordless type) during an electrical storm.
-
Page 7: Table Of Contents
Table of Contents Introduction Important safety information ....... . 3 Table of Contents A Look at the Operation Panel 1. - Page 8 Table of Contents 5. Receiving Documents Using FAX Mode ........71 Using TEL Mode .
-
Page 9: A Look At The Operation Panel
A Look at the Operation Panel FACE DOWN (MAX 10 SHEETS) TEL FAX SPEED RECEPTION VOLUME DIAL MODE DOWN REPEAT REC/MEMO PLAY/SKIP RESOLUTION FUNCTION REDIAL DELETE HOLD/ PQRS WXYZ COPY/HELP SEARCH STOP 04/POLL OpenLCR SPEAKER OpenLCR START/MEMORY 12 13 SPEED DIAL key RECEPTION MODE key Press this key to dial a fax or voice Press this key to select the... - Page 10 Panel release STOP key Grasp this finger hold and pull Press this key to cancel an toward you to open the operation operation before it is completed. panel. START/MEMORY key Number keys Press this key to begin Use these keys to dial numbers, transmission when using Speed and enter numbers and letters Dialing, Direct Keypad Dialing, or...
-
Page 11: Installation
1. Installation Unpacking Checklist If any are missing, Before setting up, make contact your dealer sure you have all of the or retailer. following items. Paper tray Operation Telephone Rapid key Imaging extension manual line cord labels film cartridge Original Handset Gears (4) Imaging film... -
Page 12: Connections
Connections Connections Connecting the Handset Connecting the power cord Connect the handset as shown and Plug the power cord into a 120 V, 60 place it on the handset rest. Hz, grounded AC (3-prong) outlet. ♦ Caution! The ends of the handset cord are Do not plug the power cord into any identical, so they will go into either other kind of outlet. - Page 13 Connections Connecting the telephone Note: The fax machine is set for tone dialing. If you are on a pulse dial line, line cord you must set the fax machine for pulse dialing. Press the keys on the Insert one end of the line cord into the operation panel as follows: jack on the back of the machine marked TEL.
- Page 14 Connections Attaching the tray extension Extension phone (optional) and document support If desired, you can connect an extension phone to the TEL. SET Attach the paper tray extension. jack on the fax. ♦ Pull the paper release plate forward. Insert the paper tray Remove the seal covering the TEL.
-
Page 15: Loading The Imaging Film
The initial starter roll of imaging film When replacing the film, use a roll of included with your fax can print about Sharp UX-3CR imaging film. One roll 30 letter-size pages. can print about 100 letter-size pages. Note: If there is paper in the paper... - Page 16 Loading the Imaging Film Remove the imaging film cartridge Remove the new roll of imaging film from the print compartment (grasp from its packaging. the handle at the front of the • Do not yet remove the band that cartridge) and turn it over. holds the rolls together.
- Page 17 Loading the Imaging Film Insert the large gear into the large Rotate the large gear toward you holder on the imaging film cartridge until the film is taut. (make sure it clicks into place), and then insert the small gear on the other end of the spool into its holder.
- Page 18 FILM END Use the following imaging film, which is available from your dealer or retailer: Sharp UX-3CR Imaging Film Caution! Be sure to use only genuine Sharp supplies with the following logo: UX-3CR IMAGING FILM ROULEAU D’ IMPRESSION...
-
Page 19: Loading Printing Paper
Loading Printing Paper Loading Printing Paper You can load letter or legal size paper in the paper tray. The maximum number of sheets depends on the weight and size of the paper you are loading. ♦ Paper from 16 to 20 lbs. (60 to 75 g/m Letter size: 60 sheets Legal size: 30 sheets ♦... - Page 20 Loading Printing Paper Push the paper release plate back The fax has been set at the factory to scale the size of received faxes down. to letter size paper. If you have • If the paper release plate is not loaded legal paper, you must pushed down, paper feed errors change the paper size setting to...