Panasonic AJ-SD930BE Operating Instructions Manual page 10

CONTENTS
Parts and their functions
Front panel
M
DVCPRO 50
ON POWER
DVCPRO
DV
OFF
COUNTER
METER
FULL/FINE
RESET
L
MONITOR SELECT
R
A IN
MONITOR A VOL INPUT SELECT
PREVIEW/PREVIEW AUTO EDIT PREROLL
HEADPHONES MIX SELECT
VIDEO AUDIO
CH1 CH2 CH3 CH4 TC
PRESET MENU
UNITY
REC LEVEL
PB LEVEL VAR
O N P Q R S
T
M MONITOR SELECT (L andR) buttons
These buttons are used to select the audio signals
which are to be output to the MONITOR L and R
connectors.
Each time the L button is pressed, the signal to be
output to the MONITOR L connector is changed in the
following sequence: CH1 5 CH2 5 CH3 5 CH4 5
CUE.
Similarly, each time the R button is pressed, the signal
to be output to the MONITOR R connector is changed
in the following sequence: CH1 5 CH2 5 CH3 5
CH4 5 CUE.
Which signal has now been selected is displayed by
the lighting of the L or R lamps on the level meter
display.
When AUTO has been selected as the setup menu
No. 721 (MONI CH SEL) setting, the display is
switched in tandem with the monitor output. The
channel to which monitor output is to be switched
automatically can be selected using setup menu No.
735 (MON AUTO SEL).
N MONITOR MIX button
This button is used to select the mixed signals which
are to be output to the MONITOR L and R connectors.
Each time the MONITOR SELECT L button is pressed
while this button is held down, the signals to be output
to the MONITOR L connector change in the following
sequence: CH1 + CH2 5 CH3 + CH4 5 CH1 + CH3
5 CH2 + CH4 5 mixing release.
The mixed signals to be output to the MONITOR R
connector are changed in the same way by the
MONITOR SELECT R button.
O Headphone jack and volume control
When stereo headphones are connected to the
headphone jack, the sound during recording, playback
or editing can be monitored using the headphones.
The volume level of the headphone output and
monitor output can be adjusted using the volume
control.
Whether the volume level of the monitor output is to
be coupled to the volume control or not can be
selected using the setup menu item No. 713 (MONI
OUT). (Note that the volume level of the headphones
is coupled at all times.)
When the volume of the monitor output is not coupled,
it is fixed at a set level and is not affected by the
position of the volume control.
10 (E)
JOG SHTL SLOW
ASSEM VIDEO CUE TC STAND BY PLAYER RECORDER
CH1 CH2 CH3 CH4
EDIT PLAY REC
INSERT
A OUT
TRIM
REW STOP FF
SET
IN OUT
SUPER REC INH INT TCG MODE CONTROL
SET DIAG REGEN
ON ON TAPE REMOTE
PRESET
OFF OFF EXIT EE LOCAL
P A VOL SELECT button and lamps
(REC LEVEL, PB LEVEL)
This switches the function of the audio level control
knobs Q between recording and playback.
Each time this button is pressed (for 1 second or
longer), the functioning of the audio level control
knobs switches alternately been recording and
playback.
When the audio level control knobs Q have been set
to adjust the recording level, the REC LEVEL lamp
lights.
When they have been set to adjust the playback level,
the PB LEVEL lamp lights.
Q Audio level control knobs
These knobs are used to adjust the recording and
playback level of the PCM audio signals (CH1, CH2,
CH3 and CH4).
Whether the recording level or the playback level is to
be adjusted is selected using the A VOL SELECT
button P.
R Audio level control selector switch
UNITY:
At this position, the audio signals are recorded or
played back at a fixed level regardless of the
positions of the audio level control knobs Q.
VAR:
At this position, the audio signals are recorded or
played back at the level adjusted by the audio level
control knobs Q.
<Note>
It is not possible to set it so that both the recording
level and playback level can be adjusted.
When REC LEVEL is selected, UNITY (fixed level) is
set for the playback level; when PB LEVEL is
selected, UNITY is set for the recording level.
S TC PRESET button
This button is used to set the TC or UB value.
When the TC or UB value is to be set, this button is
pressed first to stop the data from advancing. The set
of digits whose display is flashing is then changed.
T MENU button
When this button is pressed, the setup menus are
displayed on the TV monitor (but only when the
VIDEO OUT 3 connector or SDI OUT 3 connector is
used), and the setup menu numbers appear on the
VTR's display panel.
When it is pressed again, the setup menu settings are
exited, and the original status is restored.