Chapter 9. Reading (X) And Resetting (Z) Reports - Sharp ER-A57R1 Service Manual

CHAPTER 9. READING (X) AND
RESETTING (Z) REPORTS
(1) Job #Ynm: Y = 1 when the master is in the X1/Z1 mode.
Y = 2 when the master is in the X2/Z2 mode.
(2) Master consolidation report command entry sequence
(a) To specify a range
NK1 : Machine number
NK2 : START number
NK3 : END number
X
Ynm X
Only 1 item
NK3
X TL
(b) To specify a department or group
NK1 : Machine number
NK2 : DEPT number
X
Ynm X
Z
(c) To specify nothing
NK1 : Machine number
X
Ynm X
Z
(3) Individual report command entry sequence
The same key operation as the standalone is required for entry
of an individual report JOB#.
Enter system
NK1 ST NK2
Machine number
Entire system
NK1 ST NK2 TL
Machine number
Entire system
NK1 ST TL
Machine number
(4) Syetem sales report for master/backup master
OP X/Z
REPORT NAME X
GENERAL
DEPT/GROUP
IND. GROUP
GROUP TOTAL
PLU BY RANGE
PLU BY DEPT
PLU IND. GR.
PLU GR. TL
PLU STOCK
PLU ZERO SALES
PLU ZERO SALES
BY DEPT
PLU MINIMUM
STOCK
TRANSACTION
TL-ID
COMMISSION
SALES
TAX
CHIFF
ALL CLERK
Φ
IND. CLERK
HOURLY (ALL)
HOURLY (RANGE)
DAILY NET
GLU
GLU BY CLERK
BALANCE
STACKED REP
Reset clear
∗1
X1 : Daily X report
X2 : Preriodic X report
∗2
The time interval range, or PLU code range can be specified by
entering the start and end numbers according to the following
procedure. When specifying a single time interval, PLU code,
the start number has only to be entered.
XXXX
X
Start No.
Stop of printing reports: These system reports do not execute this
∗3
When 1 is entered in the forth digit of a job code, Inline system
reports are printed.
Example: System daily general report;
System periodic general report; job code 1200
∗4
In case of floating clerk system, this daily report can be printed
at any satellite.
(The periodic report can not be printed at any satellite.)
1 ™ 17
MODE ∗1
X1/Z1 X2/Z2
Z X1 Z1 X2 Z2 JOB#
Φ Φ Φ Φ
1 x 00
Φ Φ
1 x 10
Φ Φ
1 x 12
Φ Φ
1 x 13
Φ Φ Φ Φ
1 x 20
Φ Φ Φ Φ
1 x 21
Φ Φ
1 x 22
Φ Φ
1 x 23
Φ
1 x 24
Φ Φ
1 x 27
Φ Φ
1 x 27
Φ
1 x 28
Φ Φ
1 x 30
Φ
1 x 31
Φ Φ
1 x 32
Φ Φ
1 x 32
Φ
1 x 34
Φ Φ Φ Φ
1 x 40
Φ Φ Φ Φ Φ
1 x 41
Φ Φ
1 x 60
Φ
1 x 60
Φ Φ
1 x 70
Φ Φ
1 x 80
Φ Φ
1 x 81
Φ Φ
1 x 82
1 x 90 –
Φ Φ Φ Φ
1 x 91
Φ Φ
1 x 99
Z1 : Daily Z report
Z2 : Periodic Z report
XXXX
End No.
specification.
job code 1100
∗3 DATA FOR
READING NOTE
—
—
GROUP No
—
∗2
PLU CODE
DPT CODE
GROUP No
—
∗2
PLU CODE
ALL
DPT CODE
ALL
—
—
—
—
—
—
∗4
∗2
∗2