Orbital Sander Safety Warnings; Specifications; Standard Accessories; Prior To Operation - Hitachi SC12V Handling Instructions Manual

ORBITAL SANDER SAFETY WARNINGS

CAUTION
Prior to the sanding operation, make sure the material
you are going to sand.
If generation of harmful/ toxic dusts such as lead
paint, woods and metals is expected under the
sanding operation, make sure the dust bag or
appropriate dust extraction system is connected with
dust outlet tightly.

SPECIFICATIONS

Model
Voltage (by areas)*
Power Input*
No-Load Speed
Diam. of Orbit
Sanding pad size
Sanding paper size
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

Sanding paper ............................................................ 1
Dust bag (for model SV12V, SV12SD) ...................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
1. Sanding paper
Perforated sanding paper for Model SV12V, SV12SD.
Non-perforated sanding paper for Model SV12SE.
Grain: AA40, AA60, AA80, AA100, AA120, AA150,
AA180, AA220, AA240.
(1) Standard Type (Perforated or non-Perforated), 114 ×
280 mm
(2) Pressure Sensitive Type (Perforated or non-
Perforated), 114 × 228 mm
2. Magic Pad (Pressure Sensitive Type), 114 × × × × × 228 mm
(1) Perforated Pad (for Model SV12V, SV12SD)
(2) Non-Perforated Pad (for Model SV12SE)
3. Cleaner Adaptor (for Model SV12V, SV12SD).
4. Punch plate (for Model SV12V, SV12SD)
Optional accessories are subject to change without notice.
APPLICATIONS
Finish polishing of woodwork surfaces
Sanding surfaces of woodwork or sheet metal prior
to painting, etc.
Wear the dust mask additionally, if available.
Do not inhale or touch the harmful / toxic dusts
generated in sanding operation, the dust can
endanger the health of yourself and bystanders.
SV12V
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
–1
4000 – 10000 min
2.8 kg

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a power receptacle while
the power switch is in the ON position, the power
tool will start operating immediately, which could
cause a serious accident.
3. Extension cord
When the work area is remote from the power source,
use an extension cord of sufficient thickness and
rated capacity. The extension cord should be kept as
short as practicable.
4. Attaching sanding paper
(Start at Switch handle's side)
(1) Open Paper holder by turning clamping lever (Fig. 1).
(2) Place the sander as shown in Fig. 2. Insert the
sanding paper between the paper holder and the
bottom plate until it can go no further.
(3) Match the width of the sanding paper with the
width of the pad. Return the clamping lever to it
original position to secure the sanding paper.
(4)-1 When using perforated sanding paper.
To secure the other end of the sanding paper, pull
the sanding paper while aligning the holes of the
sanding paper with the holes of the pad.
(4)-2 When using non-perforated sanding paper.
Align the sanding paper on the pad and pull the
sanding paper to secure the other end.
SV12SD
300 W
10000 min
2.4 mm
114 mm × 228 mm
114 mm × 280 mm
2.8 kg
English
SV12SE
–1
2.6 kg
22