1. Manuals
  2. Brands
  3. Dell Manuals
  4. Server
  5. PowerEdge FX2
  6. Configuration manual

Dell PowerEdge FX2 Configuration Manual

Upgrading from 10gbe pass-through modules to fn410s i/o modules
Hide thumbs Also See for PowerEdge FX2:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual , User Manual
PowerEdge FX2 - Upgrading from 10GbE
Pass-through Modules to FN410S I/O Modules
Dell Networking Solutions Engineering
June 2016
A Dell EMC Deployment and Configuration Guide

Advertisement

Table of Contents
loading

Related Manuals for Dell PowerEdge FX2

Summary of Contents for Dell PowerEdge FX2

  • Page 1 PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules Dell Networking Solutions Engineering June 2016 A Dell EMC Deployment and Configuration Guide...

  • Page 2: Revisions

    Trademarks used in this text: Dell™, the Dell logo, PowerEdge™ and Force10™ are trademarks of Dell Inc. Other Dell trademarks may be used in this document. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and/or names or their products and are the property of their respective owners.

  • Page 3: Table Of Contents

    Half-width servers with dual-port CNAs ......................20 Half-width servers with quad-port CNAs......................21 Full-width servers with dual-port CNAs ......................22 Full-width Servers with quad-port CNAs......................23 Support and feedback ..............................24 PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 4: Introduction

     Resetting to factory defaults  Establishing a remote or serial connection to the management interface  Disabling and re-enabling Uplink Failure Detection (UFD) PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 5: Hardware

    Dell PowerEdge FX2s (back) with two PowerEdge FN410S IOMs installed Note: This guide applies to either the PowerEdge FX2 or FX2s chassis. The FX2 does not offer PCIe expansion slots. The FX2s includes eight PCIe expansion slots, as Figure 2 shows.
  • Page 6 FX2 with server and networking modules FX2 module descriptions PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 7: Dell 10Gbe Pass-Through Module

    Dell 10GbE Pass-through Module The Dell 10GbE PTM provides one-to-one connectivity from blade server network adapter ports to ToR switch ports. It has eight internal ports and eight external SFP+ ports. The pass-through module does not do any switching. PowerEdge FN410S I/O Module The PowerEdge FN410S IOM is a Layer 2 and 3 switch with eight internal ports and four external SFP+ ports.

  • Page 8: Upgrade

    Dell EMC recommends a minimum of two uplinks from each FN410S for redundancy. If an uplink fails, traffic continues to flow on the remaining uplink(s) in the port channel without affecting connectivity of the server CNAs.

  • Page 9: Step-By-Step Example

    In this example, there are two FC630 servers in the chassis, and each FC630 server has a dual-port CNA. On each server, one CNA port is untagged in the default vlan and the other port is tagged in VLAN 6. A Dell Networking S4048-ON functions as the ToR switch.
  • Page 10 CNA port 2 te 0/5 FC630 Po 11 192.168.1.3 default VL AN Slot 3 VL AN 6 Step-by-step example - after upgrade with FN410S IOMs installed PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 11: Part 1 - Configure The Tor Switch

    S4048-ON(conf-if-range-te-1/7-1/8)#description LINK TO FN410S-A2 S4048-ON(conf-if-range-te-1/7-1/8)#port-channel-protocol lacp S4048-ON(conf-if-range-te-1/7-1/8-lacp)#port-channel 11 mode active S4048-ON(conf-if-range-te-1/7-1/8-lacp)#exit S4048-ON(conf-if-range-te-1/7-1/8)#exit S4048-ON(conf)#interface port-channel 11 S4048-ON(conf-if-po-11)#portmode hybrid S4048-ON(conf-if-po-11)#switchport S4048-ON(conf-if-po-11)#description PO TO FN410S-A2 S4048-ON(conf-if-po-11)#no shutdown S4048-ON(conf-if-po-11)#exit PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 12: Part 2 - Replace The Ptm In Slot A1 With An Fn410S

    On FN410S-A1, UFD detects port channel 128 is up and brings up the internal, server-facing ports (FN410S-A1 ports te 0/1 and te 0/5 in Figure 9). This causes the corresponding server CNA ports to come up. PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...
  • Page 13 Note: If you want to verify east-west traffic bypasses the ToR switch by shutting port channel 128, disable UFD on the FN410S first. Instructions for disabling and re-enabling UFD are in the appendix of Dell PowerEdge FN IOM Easy Deployment Guide. PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 14: Part 3 - Replace The Ptm In Slot A2 With An Fn410S

    FX2 chassis from an upstream device on all applicable VLANs traversing FN410S-A2. The upstream server at 192.168.1.6 successfully pings the FX2 servers at 192.168.1.1 and 192.168.1.3 through the ToR and FN410S-A2 on VLAN 6. PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...
  • Page 15 UFD on the FN410S first. Instructions for disabling and re-enabling UFD are in the appendix of Dell PowerEdge FN IOM Easy Deployment Guide. All connections have been verified and the upgrade is complete. PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 16: A References And Additional Resources

    Dell PowerEdge FN I/O Module (FN IOM) - Easy Deployment Guide Dell TechCenter Networking Home Manuals and Documentation for PowerEdge FX2/FX2s and Modules PowerEdge FX2 – FN I/O Module – VLT Deployment Guide PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 17: B Components Used In This Guide

    Dell 10GbE pass-through module PowerEdge FN410S IOM Dell Networking OS 9.10(0.1) Dell Networking S4048-ON ToR switch Dell Networking OS 9.10(0.1) PowerEdge FX2 Chassis Management Controller 1.30 PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 18: C Terminology

    FN IOA (FN I/O Aggregator): Legacy term for FN IOM. FN IOM (FN I/O Module): FN IOM refers to the switch modules on the rear of the Dell PowerEdge FX2/FX2s chassis that receive and transmit network IO from the blade servers. This includes the PowerEdge FN410S, FN410T and FN2210S.

  • Page 19: Dfn Iom Internal Port Mapping

    FN IOM A1 (Top) FN IOM A2 (Bottom) Server Slot Internal Port Numbers Internal Port Numbers Note: Quad-port CNAs are not available for quarter-width servers. PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 20: Half-Width Servers With Dual-Port Cnas

    Half-width servers with dual-port CNAs Half-width servers with dual-port CNAs FN IOM A1 (Top) FN IOM A2 (Bottom) Server Slot Internal Port Numbers Internal Port Numbers PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 21: Half-Width Servers With Quad-Port Cnas

    Half-width servers with quad-port CNAs Half-width servers with quad-port CNAs FN IOM A1 (Top) FN IOM A2 (Bottom) Server Slot Internal Port Numbers Internal Port Numbers PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 22: Full-Width Servers With Dual-Port Cnas

    FN IOM A1 (Top) FN IOM A2 (Bottom) Server Slot Internal Port Numbers Internal Port Numbers 1 , 3 1 , 3 5 , 7 5 , 7 PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 23: Full-Width Servers With Quad-Port Cnas

    1 , 2 , 3 , 4 1 , 2 , 3 , 4 5 , 6 , 7 , 8 5 , 6 , 7 , 8 PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

  • Page 24: E Support And Feedback

    Feedback for this document We encourage readers of this publication to provide feedback on the quality and usefulness of this deployment guide by sending an email to Dell_Networking_Solutions@Dell.com. PowerEdge FX2 - Upgrading from 10GbE Pass-through Modules to FN410S I/O Modules | version 1.0...

Table of Contents