Panel Tuning Mode; Transceiver Tuning (To Enter Tuning Mode); Lcd Display In Panel Tuning Mode - Kenwood NX-5700 Service Manual

No. RX
13 Single Tone Decode
(979.9Hz)
14 None
15 None
16 MSK Decode
P25 Phase1 signaling
No. RX
1 NAC 293
2 NAC 023
3 NAC 5EA
4 None
5 NAC 293
6 NAC 293
7 NAC 293
8 NAC 293
9 None
10 None
11 Tone Pattern
12 Silence Pattern
13 Audio Test Pattern
14 Vocoder Loop
P25 Phase2 signaling
No. RX
1 STTP-OB-1031-0
2 None
3 STTP-OB-1031-1
4 STTP-OB-1031-1
5 STTP-OB-1031-1
6 STTP-OB-1031-1
7 STTP-OB-1031
8 Tone Pattern (Half rate) STTP-IB1031-1
9 Silence Pattern
(Half Rate)
10 Audio Test Pattern
(Half Rate)
11 Codec Loop
12 Vocoder Loop
(Half Rate)
1-38 (No.RA020<Rev.002>)
TX
Single Tone Encode
(979.9Hz)
Single Tone Encode
(1000Hz)
MSK PN9
MSK Encode
TX
NAC 293
NAC 023
NAC 5EA
PN9
Symbol Rate Pattern
1/3 Deviation Pattern
0 Continuous Pattern
Fidelity Pattern
FSW+PN9
1011Hz Tone Test Pattern
1011Hz Tone Test Pattern
Silence Pattern
NAC293 + Audio Test Pat-
tern
None
TX
STTP-IB1031-1+Audio
PN9 Phase2
Symbol Rate Pattern
Phase2
1/3 Deviation Pattern
Phase2
0 Continuous Pattern
0 Burst Pattern
Symmetrical
STTP-IB1031-1
STP-IB-1 +
Silence Pattern (Half Rate)
STTP-IB1031-1 + Audio
Test Pattern (Half Rate)
STTP-IB1031-1 + Codec
Loop
STTP-IB1031-1 +
Vocoder Loop (Half Rate)
NXDN Mode signaling
No. RX
1 RAN1
2 None
3 RAN1
7 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
RAN: Radio Access Number
PN9: Pseudo-Random Pattern
No.7, 9 Item: PC test mode only
4.3

Panel Tuning Mode

4.3.1 Transceiver tuning (To enter tuning mode)

To enter tuning mode, press the [
is in test mode. Use the [ ] key to write tuning data through tun-
ing modes, and the [  ]/[  ] key to adjust tuning requirements
(1 to 4096 appears on the LCD).
Use the [ ] key to select the adjustment item through tuning
modes. Use the [ ] key to adjust 4, 6 or 8 reference level ad-
justments, and use the [  ] key to switch between Wide5k/
Wide4k/Narrow.

• LCD display in panel tuning mode

CV voltage, AD value, etc
Sub LCD 2.6 Low1
display
An RAST
Main LCD
display
Proper value guide
(When the frequency
An: Analog narrow mode
adjustment is necessary,
As: Analog wide 4k mode *1
Aw: Analog wide mode
P1: P25 Phase1 mode Adjustment item
P2: P25 Phase2 mode
Nn: NXDN narrow mode
Nv: NXDN very narrow mode
*1: Wide 4k is displayed only when the PC test mode is used. However, it aims
at production for factory, or a operation verification of the transceiver. It is
not necessary in operation of the transceiver to adjust.
4.3.2 Key operation
Key
Push
[+] Volume up
[-] Volume down
[  ] Adjustment value up
[  ] Adjustment value down
[  ] Auto adjustment start
[  ] Wide/Narrow/P25/NXDN -
[ ] Shift to panel test mode
[ ] To enter 5,9 or 17 refer-
ence level adjustments
[ ] Writes the adjustment
value
TX
RAN1
PN9
Maximum Deviation
Pattern
FSW + PN9
] key while the transceiver
256
Adjustment value
Adjustment point
(1~4096)
Low1 High1
Low2 High2
Low3 High3
Center1
or is displayed.)
Center2
Center3
Function
Hold (1 second)
Continuation up
Continuation down
Continuation up
Continuation down
-
-
-
-