Adjustment Item Supplement; 5 Or 9 Reference Level Adjustments Frequency; Receive Assist, Transmit Assist - Kenwood NX-5700 Service Manual

Key
Push
[ ] Go to next adjustment
item
[AUX Output tone pattern
(Orange)] change of balance ad-
justment (A change is
possible only during bal-
ance adjustment.)
[PTT] Transmit
(MIC)
[0] to [9] -
and
[#],[ ]
(MIC)

4.3.3 5 or 9 reference level adjustments frequency

High Maximum Power, Medium Maximum Power, Low Maxi-
mum Power, High Transmit Power Limit, Mid Transmit Pow-
er Limit, Low Transmit Power Limit, High Transmit Power,
Medium Transmit Power, Low Transmit Power, Maximum
Deviation , P25 High Deviation, P25 H-CPM Deviation, NXDN
High Deviation, QT Deviation, DQT Deviation, LTR Devia-
tion, DTMF Deviation, Single Tone Deviation, MSK Devia-
tion, CW ID Deviation, Sensitivity 1, Sensitivity 2, RSSI
Reference, Open Squelch, Low RSSI, High RSSI, Tight
Squelch
Tuning point Display
1 Low 1
2 Low 3
3 Center 2
4 High 1
5 High 3

Receive Assist, Transmit Assist

Tuning point Display
1 Low 1
2 Low 2
3 Low 3
4 Center 1
5 Center 2
6 Center 3
7 High 1
8 High 2
9 High 3
Function
Hold (1 second)
Back to last adjustment
item (At the time of 5, 9 or
17 point adjustment: Ad-
justment point change)
-
RX (MHz) TX (MHz)
136.05000 136.10000
145.55000 145.60000
155.05000 155.10000
164.55000 164.60000
173.95000 173.90000
RX (MHz) TX (MHz)
136.05000 136.10000
140.80000 140.85000
145.55000 145.60000
150.30000 150.35000
155.05000 155.10000
159.80000 159.85000
164.55000 164.60000
169.30000 169.35000
173.95000 173.90000

4.3.4 Adjustment item supplement

Adjustment Item Description
Receive Assist The lock voltage of VCO (Receive) is ad-
justed.
This item must be adjusted before all ad-
justment items for receiver section are ad-
justed.
Transmit Assist The lock voltage of VCO (Transmit) is ad-
justed.
This item must be adjusted before all ad-
justment items for transmitter section are
adjusted.
Frequency Frequency is adjusted under receiving
condition with SSG.
The SSG needs 0.003ppm accuracy so
please use a standard oscillator if neces-
sary.
This item can be adjusted only in PC Test
Mode so that the adjustment value is not
changed easily.
Ramp Offset Adjust this item to the optimal Ramp volt-
age.
High Maximum High Maximum Power is adjusted.
Power
Medium Maximum Medium Maximum Power is adjusted.
Power
Low Maximum Low Maximum Power is adjusted.
Power
High Transmit Pow- High Transmit Power Limit is adjusted.
er Limit
Medium Transmit Medium Transmit Power Limit is adjusted.
Power Limit
Low Transmit Pow- Low Transmit Power Limit is adjusted.
er Limit
High Transmit High Transmit Power is adjusted.
Power
Medium Transmit Medium Transmit Power is adjusted.
Power
Low Transmit Pow- Low Transmit Power is adjusted.
er
Balance The transmit modulation frequency re-
sponse is adjusted.
This item is adjusted so that the deviation
of 2kHz becomes the same deviation of
20Hz.
This item must be adjusted before all ad-
justment items for deviations are adjusted.
High Deviation High Deviation of P25/NXDN is adjusted.
(P25/NXDN)
Maximum Deviation Maximum Deviation of Analog (Wide/Nar-
(Analog Wide/Nar- row) is adjusted.
row) This item must be adjusted before all ad-
justment items for tone deviations are ad-
justed.
QT Deviation QT tone deviation is adjusted.
DQT Deviation DQT tone deviation is adjusted.
LTR Deviation LTR tone deviation is adjusted.
(No.RA020<Rev.002>)1-39