Page 2
No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any lia-...
S5U13U00P00C100 USB Adapter board so that it can be used with a laptop or desktop computer, via USB 2.0. This user manual is updated as appropriate. Please check the Epson Research and Development Website at www.erd.epson.com for the latest revision of this document before beginning any development.
• 14-pin DIP socket (if a clock other than 24MHz must be used) • 3.3V input power • On-board voltage regulator with 2.5V output • On-board voltage regulator with adjustable 6~24V output, 40mA max., to provide power for LED backlight of LCD panels. EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
= Required settings when using S5U13U00P00C100 USB Adapter board The following figure shows the location of DIP switch SW1 on the S5U13517P00C100 board. DIP Switch Figure 3-1: Configuration DIP Switch (SW1) Location S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...
1 and 2 of the jumper. The jumper associated with each power supply is as follows: J1 for COREVDD J2 for IOVDD J3 for PLLVDD J2, J1 Figure 3-2: Configuration Jumper Locations (J1, J2, J3) EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
Page 9
When the jumper is at position 3-4, the second oscillator is selected. When the jumper is at position 5-6, the CLKI pin is forced to GND. Figure 3-3: Configuration Jumper Location (J4, J5, J6) S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...
IOVDD can be in the range of 3.0~3.6V. When J4 is set to the 1-2 position, IOVDD is connected to 3.3V. If a different voltage is required for IOVDD, set JP4 to the 2-3 position and connect the external power supply to pin 32 of connector CN1. EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
The S1D13517 Display Controller on the S5U13517P00C100 evaluation board can be reset using a push-button (SW2), or via an active low reset signal from the host development platform (pin 33 on the CN1 connector). Figure 4-1: Second oscillator and Reset switch Location (Y2, SW2) S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...
The following figure shows the location of host bus connector CN1. CN1 is a 0.1x0.1 inch 34-pin header (17x2). Figure 4-2: Host Bus Connector Location (CN1) For the pinout of connector CN1, see Chapter 6, “Schematic Diagrams” on page 18. EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
For the pinout of connectors P1 and P2, see Chapter 6, “Schematic Diagrams” on page 18. Note A windows driver must be installed on the PC when the S5U13517P00C100 is used with the S5U13U00P00C100 USB Adapter Board. The S1D13xxxUSB driver is available at www.erd.epson.com. S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...
CCFL backlight. Usually, the inverter current consumption is higher than the maximum 40mA current available from the on-board voltage regulator. The following diagram shows the location of the LCD panel connectors CN3 and CN5. Figure 4-4: LCD Panel Connectors Location (CN3, CN5) EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)
The following figure shows the location of the GPO and PWM connector, CN4. Figure 4-5: GPIO and PWM Connector Location (CN4) For the pinout of connector CN4, see Chapter 6, “Schematic Diagrams” on page 18. S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...
7.1 Documents • Epson Research and Development, Inc., S1D13517 Hardware Functional Specification, document number X92A-A-001-xx • Epson Research and Development, Inc., S5U13U00P00C100 USB Adapter Board User Manual, document number I00Z-G-018-xx 7.2 Document Sources • Epson Research and Development Website: http://www.erd.epson.com S5U13517P00C100 Evaluation Board User Manual (Rev.
Page 22
S1D13517 Display Controller Change Record X92A-G-001-01 Revision 1.0 - Issued: May 8, 2009 • initial release EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)