S1D13743 Mobile Graphics Engine S5U13743P00C100 Evaluation Board User Manual Document Number: X70A-G-001-01 Status: Revision 1.0 Issue Date: 2007/08/15 Revision 1.0...
Page 2
This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product. The user should use it properly and in a safe manner. Seiko Epson does not assume any responsibility or liability of any kind of damage and/or fire caused by the use of it.
Page 4 Epson Research and Development Vancouver Design Center S1D13743 S5U13743P00C100 Evaluation Board User Manual X70A-G-001-01 Issue Date: 2007/08/15 Revision 1.0...
1 Introduction This manual describes the setup and operation of the S5U13743P00C100 Evaluation Board. The evaluation board is designed as an evaluation platform for the S1D13743 Mobile Graphics Engine. The S5U13743P00C100 evaluation board can be used with many native platforms via the host connector which provides the appropriate signals to support a variety of CPUs.
The S5U13743P00C100 Evaluation Board includes the following features: • 121-pin FCBGA S1D13743 Mobile Graphics Engine • Header with all S1D13743 Host Bus Interface signals • Headers for connection to the S5U13U00P00C100 USB Adapter board • Headers for connecting to LCD panels •...
3.1 Configuration DIP Switch The S1D13743 has 3 configuration inputs (CNF[2:0]). A DIP switch (SW1) is used to configure CNF[2:0] as described below. Table 3-1: Summary of Power-On/Reset Options...
Page 8 Epson Research and Development Vancouver Design Center 3.2 Configuration Jumpers The S5U13743P00C100 has 6 jumpers which configure various board settings. The jumper positions for each function are shown below. Jumper Function Position 1-2 Position 2-3 No Jumper COREVDD current...
Page 9
Vancouver Design Center JP1, JP2, JP3, JP5 - Power Supplies for the S1D13743 JP1, JP2, JP3, JP5 can be used to measure the current consumption of each S1D13743 power supply. When the jumper is at position 1-2, normal operation is selected.
Page 10
Page 10 Epson Research and Development Vancouver Design Center JP4 - IOVDD Source JP4 is used to select the source for the IOVDD supply voltage. When the jumper is at position 1-2, the IOVDD voltage must be provided to the H1 connector, pin 32.
Page 11
Epson Research and Development Page 11 Vancouver Design Center JP6 - SIOVDD Source JP6 is used to select the source for the PIOVDD supply voltage. When the jumper is at position 1-2, the PIOVDD voltage must be provided to the H4 connector, pin 8.
The S5U13743P00C100 evaluation board has an on-board linear regulator to provide the 1.5V power required by the S1D13743 Mobile Graphics Engine. It also has a step-up switching voltage regulator to generate adjustable 6~24V, which can be used to power the LED backlight on some LCD panels.
IOVDD voltage must be used at Y2. The on-board 4MHz oscillator is not specified to work below a 3.0V supply voltage. The S1D13743 MGE can output the input clock on the CLKOUT pin depending on the state of the CLKOUTEN input. Both these signals are available on the H4 connector: CLKOUT on pin 1 and CLKOUTEN on pin 4.
4.5 Host Interface 4.5.1 Direct Host Bus Interface Support All S1D13743 host interface pins are available on connector H1 which allows the S5U13743P00C100 evaluation board to be connected to a variety of development platforms. For detailed S1D13743 pin mapping, refer to the S1D13743 Hardware Functional Specification, document number X70A-A-001-xx.
Epson Research and Development Page 15 Vancouver Design Center 4.5.2 Connecting to the Epson S5U13U00P00C100 USB Adapter Board The S5U13743P00C100 evaluation board is designed to connect to a S5U13U00P00C100 USB Adapter Board. The USB adapter board provides a simple connection to any computer via a USB 2.0 connection.
Epson Research and Development Vancouver Design Center 4.6 LCD Panel Interface The LCD interface signals are available on connectors H2 and H3. For S1D13743 LCD interface pin mapping, refer to the S1D13743 Hardware Functional Specification, document number X70A-A-001-xx. Connector H2 is 0.1x0.1” 20-pin header (10x2) and connector H3 is 0.1x0.1” 40-pin header (20x2).
Page 17 Vancouver Design Center 4.7 GPIO Connections The S1D13743 Mobile Graphics Engine has 8 GPIO pins. All the GPIO pins are routed to the H4 connector. Note that connector H4 is not populated on the S5U13743P00C100 evaluation board. The following figure shows the location of the GPIO connector, H4.
Page 18 Epson Research and Development Vancouver Design Center 5 Parts List Table 5-1: Parts List Item Reference Part Description Mfg / Mfg PN / Notes C1, C2, C3, C4, C9, C12, C13, C14, C18, C19, C20, Yageo America 0.1uF...
Page 19
Epson Research and Development Page 19 Vancouver Design Center Table 5-1: Parts List Item Reference Part Description Mfg / Mfg PN / Notes Panasonic - ECG ELL-6SH100M 10uH IND_ELL6 COIL 10UH 1300MA CHOKE SMD P1, P2 HEADER_20X2 HDR2X20/2MM 3M 151240-8422-RB...
Page 20
Page 20 Epson Research and Development Vancouver Design Center Table 5-1: Parts List Item Reference Part Description Mfg / Mfg PN / Notes Texas Instruments TPS76915DBVT TPS76915DBVT SOT23-5 IC 1.5V 100MA LDO REG SOT-23-5 TI TPS61040DVBR TPS61040 SOT23-5 IC CONV DC/DC BOOST...
Epson Research and Development Page 21 Vancouver Design Center 6 Schematic Diagrams Figure 6-1: S5U13743P00C100 Schematics (1 of 3) S5U13743P00C100 Evaluation Board User Manual S1D13743 Issue Date: 2007/08/15 X70A-G-001-01 Revision 1.0...
Page 22
Page 22 Epson Research and Development Vancouver Design Center Figure 6-2: S5U13743P00C100 Schematics (2 of 3) S1D13743 S5U13743P00C100 Evaluation Board User Manual X70A-G-001-01 Issue Date: 2007/08/15 Revision 1.0...
Page 23
Epson Research and Development Page 23 Vancouver Design Center Figure 6-3: S5U13743P00C100 Schematics (3 of 3) S5U13743P00C100 Evaluation Board User Manual S1D13743 Issue Date: 2007/08/15 X70A-G-001-01 Revision 1.0...
Page 24 Epson Research and Development Vancouver Design Center 7 Board Layout Figure 7-1: S5U13743P00C100 Board Layout - Top View S1D13743 S5U13743P00C100 Evaluation Board User Manual X70A-G-001-01 Issue Date: 2007/08/15 Revision 1.0...
Page 25
Epson Research and Development Page 25 Vancouver Design Center Figure 7-2: S5U13743P00C100 Board Layout - Bottom View S5U13743P00C100 Evaluation Board User Manual S1D13743 Issue Date: 2007/08/15 X70A-G-001-01 Revision 1.0...
Page 26 Epson Research and Development Vancouver Design Center 8 References 8.1 Documents • Epson Research and Development, Inc., S1D13743 Hardware Functional Specification, document number X70A-A-001-xx. 8.2 Document Sources • Epson Research and Development Website: http://www.erd.epson.com. S1D13743 S5U13743P00C100 Evaluation Board User Manual...
Fax: 2827-4346 http://www.epson-electronics.de/ Fax: (65) 6271-3182 http://www.epson.com.hk/ http://www.epson.com.sg/ 9.2 Ordering Information To order the S5U13743P00C100 Evaluation Board, contact the Epson sales representative in your area and order part number S5U13743P00C100. S5U13743P00C100 Evaluation Board User Manual S1D13743 Issue Date: 2007/08/15 X70A-G-001-01...
Page 28
Page 28 Epson Research and Development Vancouver Design Center Change Record X70A-G-001-01 Revision 1.0 - Issued: August 15, 2007 • created from X63A-G-002-01 • updated for the S1D13743 S1D13743 S5U13743P00C100 Evaluation Board User Manual X70A-G-001-01 Issue Date: 2007/08/15 Revision 1.0...