Page 2
BS2000 Servers and Operating System at http://manuals.ts.fujitsu.com/index.php?id=1-4 Replication functions for BS2000 volumes in ETERNUS DX/AF are provided by Fujitsu Software BS2000 SHC- OSD and StorMan. Information on SHC-OSD can be found in the manual and release notices at http://manuals.ts.fujitsu.com/index.php?id=1.
Page 3
Examples for the setup of ETERNUS DX/AF storage systems and BS2000 Server. Acknowledgements • The company names, product names and service names mentioned in this document are registered trademarks or trademarks of their respective companies. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
Page 4
The following naming conventions are used to describe BS2000 server models in this document. BS2000 server model Naming conventions SE300, SE500, SE700, SE300B, SE500B, SE700B SE Server series S175, S210 S-Server series SQ210 SQ-Server series FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
Set Up the BS2000 Server for ETERNUS DX/AF Storage Systems SE Server (SU /390) ......................21 S-Server ..........................21 SE Server (SU x86) and SQ-Server ..................22 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
Page 6
Configuration and Generation of an ETERNUS DX8700 S3 for BS2000 (SE Server) ..... 24 Generation of the ETERNUS DX8700 S3 on the SE Server (SU /390) and S-Server ....27 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED...
Page 7
FC-AL connection settings (Host-direct-connection) - not for SE Server (SU /390) and S-Servers, not for ETERNUS DX8700 S3! ........................16 Table 4.2 Fabric connection settings (Host-Fabric-connection) .................. 16 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
Chapter 1 Workflow Documents required during the workflow: • FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX S4/S3 series Hybrid Storage Systems, ETERNUS AF series, ETERNUS DX200F All-Flash Arrays Settings • FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel)
Page 9
On SE Server (SU /390) and S-Server do the generation as described in manual "System installation". On SE Server (SU X86) or SQ-Server do the set up as described in manual "FUJITSU Server BS2000 SE300 / SE500 / SE700, Operation and Administration" or "SQ Business Server Operation and Administration".
The feature Transparent failover (TFO) / Storage Cluster Option is supported for BS2000 volumes as of OSD/ BC V10 and OSD/XC V10 with SHC-OSD V13.0. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
(1 minute) must be reset via /MODIFY-IO-UNIT. For online firmware upgrades in 'operator intervention mode', additional conditions apply. Please respect 'important notices' and 'restrictions' in the storage bulletins. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
CH (CH/SUBCH STATUS) and call the CH/SUBCH STATUS DISPLAY FRAME execute Function 4 (FC PORT STATUS): the field SELF P-NAME shows the WWN SQ-Server: Use the command below to get the WWN: chk_conf -c FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
For further details, refer to "ETERNUS DX/AF Storage Systems Server Connection Guide (Fibre Channel) Fibre Channel Switch Settings Administrator’s Guide". Controller Category Action DX/AF series Connectivity > Port Group > FC Configure FC Port FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
Page 16
ETERNUS DX/AF storage system CA type 32Gbit/s CA 16Gbit/s CA 8Gbit/s CA 16Gbit/s 16Gbit/s 16Gbit/s 8Gbit/s 8Gbit/s 8Gbit/s 8Gbit/s 8Gbit/s 4Gbit/s — 4Gbit/s 4Gbit/s 2Gbit/s — — 2Gbit/s FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
We recommend assigning a name which identifies the host and the slot and port number of the FC channel (e.g. FC channel in slot 2 port 0 on the host host1 -> Name "host1-2-0"). FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED...
"Capacity". The recommended capacity of the logical volumes for BS2000 should be between 25 GB and 100 GB. The maximum supported LUN capacity is 2TB. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
They are required to connect the ETERNUS DX/AF storage system to the server. Controller Category Action DX/AF series Component > Controller Enclosure > Channel Adapters > CA — FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
For performance reasons each volume should be configured with one or two additional PAV alias devices. D3435 (internal type A5) must be specified as disk device type. (See manual "BS2000 System Installation" and the example in the annex.) FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
Set up the SE Server (SU x86) or the SQ-Server for BS2000 disks on an ETERNUS DX/AF storage system. Use the SE Manager or SQ-Manager GUI as described in the manuals “FUJITSU Server BS2000 SE300 / SE500 / SE700, Operation and Administration” resp. “SQ Business Servers, Operation and Administration” to configure LUNs on the ETERNUS DX/AF storage system as D3435 disk devices.
Web GUI or by using the X2000 command "emptool display paths" for the SQ-Server and the SE Server. Use /ATTACH-DEVICE and /SHOW-DISK-STATUS for checks by means of BS2000, resp. /SHOW-STORAGE-DEVICE- CONFIG for checks by means of SHC-OSD. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
4 zones (2 x 2) are configured for the channel paths in the FC fabrics. ■ Configuration of the ETERNUS DX8700 S3 First, configure the host-related settings in the DX8700 S3. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
Page 25
4 RAID groups from RG01 to RG04 are set up. The assignment of the RAID groups to the CPUs is made manually as follows: RAID group CPU# RAID Type RAID1 RG01 RAID1 RG02 RAID1 RG03 RAID1 RG04 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
Page 26
All FC ports (CAs) assigned to one affinity group or referring the same LUN group must be assigned to the same reset group. FC Ports CE#0 CM#0 CA#0 Port#0 CE#1 CM#0 CA#1 Port#1 CE#0 CM#1 CA#1 Port#1 CE#1 CM#0 CA#0 Port#0 FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
For the same 80 logical volumes, another 80 PAV alias devices are generated with MNs from 26A0 to 26EF and with PAV addresses from 0xA0 to 0xEF: DVC 26A0,A5,D,0000,(2600),(2601),MULT=80,PAV=A0 The address range from 0xF0 to 0xFF remains unused. FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- Copyright 2018 FUJITSU LIMITED P3AM-5672-10ENZ0...
Page 28
However, Fujitsu shall assume no responsibility for any operational problems as the result of errors, omissions, or the use of information in this manual. • Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual.