Kenwood NX-800 Service Manual page 11

7. If writing ends successfully, the checksum is calculated
and a result is displayed.
8. If you want to continue programming other transceivers,
repeat steps 4 to 7.
Note:
This mode cannot be entered if the Firmware Program-
ming mode is set to Disable in the Programming soft-
ware.
6-4. Function
1. If you press the [ ] key while "PROGRAM 115200" is
displayed, the display changes to "PROGRAM 19200"
(The LED blinks green) to indicate that the write speed
is low speed (19200 bps). If you press the [ ] key again
while "PROGRAM 19200" is displayed, the display
changes to "PROGRAM 38400" (The LED lights red and
orange alternatively). If you press the [ ] key again while
"PROGRAM 38400" is displayed, the display changes
to "PROGRAM 57600" (The LED blinks orange). If you
press the [ ] key again while "PROGRAM 57600" is dis-
played, the display returns to "PROGRAM 115200" (The
LED lights orange).
2. If you press the [ ] key while "PROGRAM 115200" is
displayed, the checksum is calculated, and a result is dis-
played. If you press the [ ] key again while the check-
sum is displayed, "PROGRAM 115200" is redisplayed.
Note:
Normally, write in the high-speed mode.
7. Clone Mode
Programming data can be transferred from one transceiv-
er to another by connecting them via their 8-pin microphone
connectors. The operation is as follows (the transmit trans-
ceiver is the source and the receive transceiver is a target).
The following data cannot be cloned.
• Tuning data
• Embedded message with password
• ESN (Electronic Serial Number) data
Note:
The following data can be cloned.
• Fleet (own)/ID (own) for FleetSync
• Unit ID (own) for NXDN
1. Turn the source transceiver power ON with the [ ] key
held down. If the read authorization password is set to
the transceiver, the transceiver displays "CLONE LOCK"
If the password is not set, the transceiver displays
"CLONE MODE".
2. When you enter the correct password, and "CLONE
MODE" is displayed, the transceiver can be used as the
cloning source. The following describes how to enter
the password.
REALIGNMENT /
模式组合
7. 如果写入操作成功完成，则计算校验和并显示结果。
8. 若要继续为其他车载对讲机编程，请重复步骤 4 至 7。
注意 :
如果车载对讲机的固件编程模式设为禁用，则无法进入此
模式。
6-4. 功能
1. 如果在显示"PROGRAM 115200"时按 [ ] 键，则显示变为
"PROGRAM 19200"(LED 呈绿色闪烁 )，表示写入速度为低
速 (19200bps)。如果在显示"PROGRAM 19200"时再次按
[ ] 键，则显示变为"PROGRAM 38400"(LED 呈红色和橙
色交替点亮 )。如果在显示"PROGRAM 38400"时再次按 [
] 键，则显示变为"PROGRAM 57600"(LED 呈橙色闪烁 )。
如果在显示"PROGRAM 57600"时再次按 [ ] 键，则显示
返至"PROGRAM 115200"(LED 呈橙色点亮 )。
2. 如果在显示"P R O G R A M 115200"时按 [
验和并显示结果。如果在显示校验和时再次按 [
则重新显示"PROGRAM 115200" 。
注意 :
通常以高速模式写入。
7. 复制模式
用 8 针麦克风连接器连接车载对讲机，可以将编程数据从
一台车载对讲机传输到另一台车载对讲机。具体操作如下 ( 发
射车载对讲机是主机，接收车载对讲机是子机 )。
不能复制以下数据。
· 调谐数据
· 带密码的嵌入消息
• ESN( 电子序列号 ) 数据
注意 :
可以复制以下数据。
• FleetSync 的 Fleet( 自身 )/ID( 自身 )
• NXDN 的 Unit ID( 自身 )
1. 按住 [ ] 键打开主车载对讲机的电源。如果车载对讲机设
置了读取授权密码，则车载对讲机显示"CLONE LOCK" 。如
果未设置密码，则车载对讲机显示"CLONE MODE" 。
2. 输入正确的密码后，显示"CLONE MODE" ，车载对讲机可以
作为复制源使用。下面描述如何输入密码。
NX-800
] 键，则计算校
] 键，
11