Sealey MC402.V4 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ ThESE INSTRUCTIONS CAREFULLY. NOTE ThE SAFE OPERATIONAL REQUIREMENTS, WARNINgS & CAUTIONS.
USE ThE PRODUCT CORRECTLY AND WITh CARE FOR ThE PURPOSE FOR WhICh IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAgE AND/OR PERSONAL INJURY AND WILL INVALIDATE ThE WARRANTY. PLEASE kEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
p WARNINg! Before use, ensure the motorcycle or quadbike to be lifted has a suitable structure and centre of gravity to
accommodate the lift arms without damaging the bike. DO NOT use if the lift will foul on the exhaust or other vulnerable parts.
Remove lower fairing or obstructing trims before use and ensure the bike is adequately strapped onto the lift before operating.
Maintain the lift in good condition (use an authorised service agent).

replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

use a qualified person to lubricate and maintain the lift. DO NOT use brake fluid to top up hydraulic unit.

Locate the lift in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is adequate lighting.

Also ensure that the floor is level and strong enough (preferably concrete) to take the weight of the lift and the bike. DO NOT operate the lift
on tarmacadam, as the surface may be unstable.
Keep the lift clean for best and safest performance.

the maximum bike weight is 680kg. DO NOT exceed this rated capacity.

remove ill fitting clothing. remove ties, watches, rings and other loose jewellery, and contain long hair.

Maintain correct balance and footing, do not over reach. Ensure the floor is not slippery and wear non-slip shoes.

Ensure the bike is adequately secured to the lifting platform with appropriate straps.

Before lifting check that there are no overhead obstructions.

When platform has been raised to the working height ensure the platform safety arms are engaged to prevent accidental lowering.

Keep children and unauthorised persons away from the work area.

the lowering speed will vary according to the weight of the load and the release valve setting.

DO NOT use the lift for a task it is not designed to perform.

DO NOT operate the lift if damaged.

DO NOT exceed the rated capacity of the lift.

DO NOT operate the lift when you are tired or under the influence of alcohol, drugs or intoxicating medication.

DO NOT allow untrained persons to operate the lift.

DO NOT attempt to transport a load on the lift. the lift must only be used in a static position for raising and lowering loads.

DO NOT make any modifications to the lift and DO NOT adjust or tamper with the safety valve.

Before lowering the lift ensure that there are no obstructions underneath the platform and that all persons are standing clear.

Before storing in safe area, ensure all parts are clean and free of grease and oil. store lift in the lowest position.

2. INTRODUCTION & SPECIFICATION
Heavy steel construction with bottle jack style power unit. Arms suitable for lifting bikes with a suitable structure, quads, all terrain vehicles,
trikes and transmissions. Features mechanical safety lock to prevent inadvertent lowering. Mounted on two fixed wheels and two castors for
manoeuvrability.
Specification
capacity . . . . . . . . . . . . . . . . . . . . . . . 680kg
Minimum height . . . . . . . . . . . . . . . . 120mm
Maximum height . . . . . . . . . . . . . . . . 380mm
Weight . . . . . . . . . . . . . . . . . . . . . . . 27.2kg
© Jack sealey Limited
InstructIons for:
MOTORCYCLE & QUAD LIFT 680kg hYDRAULIC
MC402.V4
MoDEL no:
Original Language Version
Mc402.V4 Issue: 2 (sP) - 16/07/13