Sealey MC401.V3 Instructions

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear protective
instructions gloves
1. Safety
WArninG! ensure the bike is adequately strapped to the platform before operating.
‰
maintain the lift in good condition (use an authorised service agent).
9
replace or repair damaged parts. use genuine parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9
use a qualified person to lubricate and maintain the lift. do Not use brake fluid to top up hydraulic unit.
9
locate the lift in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is adequate
9
lighting. Also ensure that the floor is level and strong enough (preferably concrete) to take the weight of the lift and the bike. do not
operate the lift on tarmacadam, as the surface may be unstable.
Keep the lift clean for best and safest performance.
9
Before use, stabilise the lift by turning the side tilt screws so that the lift is just raised off of its wheels.
9
the maximum bike weight is 454kg. do Not exceed this rated capacity.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery, and contain long hair.
9
maintain correct balance and footing, do not over reach. ensure the floor is not slippery and wear non-slip shoes.
9
ensure the bike is adequately secured to the lifting platform with appropriate straps.
9
Before lifting check that there are no overhead obstructions.
9
When platform has been raised to the working height ensure the platform locking bar is engaged to prevent accidental lowering.
9
Keep children and unauthorised persons away from the work area.
9
the lowering speed will vary according to the weight of the load and the release valve setting.
9
do Not use the lift for a task it is not designed to perform.
8
do Not operate the lift if damaged.
8
do Not exceed the rated capacity of the lift.
8
do Not operate the lift when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do Not allow untrained persons to operate the lift.
8
do Not attempt to transport a load on the lift. the lift must only be used in a static position for raising and lowering loads.
8
do Not make any modifications to the lift and do Not adjust or tamper with the safety valve.
8
Before lowering the lift ensure that there are no obstructions underneath the platform and that all persons are standing clear.
9
Before storing in safe area, ensure all parts are clean and free of grease and oil. store lift in the lowest position.
9
WarNiNg! the warnings, cautions and instructions discussed in this manual cannot cover all possible conditions and situations
‰
that may occur. it must be understood that common sense and caution are factors which cannot be built into this product, but
must be applied by the operator.
2. iNtroductioN
All steel construction with heavy duty, foot operated, integral hydraulic pump and ram assembly. Fitted with platform safety lock device to fix at
two working heights of 710mm and 490mm and to prevent accidental lowering. sliding panel platform and front wheel clamp assist removal of
rear motorcycle wheel. Platform fitted with full width loading ramp. Base assembly fitted with transport wheels and lock-downs to prevent lift
moving during use. suitable for use with centre stand motorcycles or with paddock stand.
3. SpecificatioN
capacity . . . . . . . . . . . . . . . . . . . . . . . 454kg
minimum Height . . . . . . . . . . . . . . . . 190mm
maximum Height . . . . . . . . . . . . . . . 710mm
Width . . . . . . . . . . . . . . . . . . . . . . . . 690mm
length. . . . . . . . . . . . . . . . . . . . . . . 2200mm
4. aSSembly
unpack the lift and check contents with list below. should there be any damaged or missing parts contact your supplier
immediately. content
• Main Assembly
• Lifting Pedal
WarNiNg! Keep your hands away from moving parts.
‰
© Jack sealey limited
instructions for
motorcycle lift 454kg capacity
hydraulic
model no:
Wear safety Warning
crushing of
footwear
Hands
• Sliding Plate • Leading Plate
• Release Pedal • Bolts, Washers, Nuts, Cotter Pins
Original Language Version
mc401.V3
• Vice
mC401.V3 | Issue 2 08/03/17