Select Function; Set Luminance Offset; Luminance Offset (Adjust); Luminance Offset Reset - Sony LMT-300 User Manual

FUNCTION selection may be the result of an association
between a CPL and a FUNCTION or by including a
Function in the Show Playlist,

Select Function

Projector Functions are
related to the specific
Projection Type, i.e., a 3D
FUNCTION can only be
applied when the Projection
Type is set to Single 3D. A
stereoscopic based
FUNCTION contains [3D] in the Function Name.
Note: Selection of a Projector Function incompatible with
the Projection Type will result in a warning message
appearing and the selected FUNCTION not applied. Click
OK to close the message.
To select a Function, verify the correct Projection Type is
indicated adjacent to the Lamp Indicator, tap Menu, tap
Projector, tap Projector Control and then tap Change
Function. The Change Function pop-up window appears.
Tap the UP ARROW or DOWN ARROW until the
specific FUNCTION is visible and then tap the desired
FUNCTION button. Extended Function Names may be
truncated. If there is a question as to the FUNCTION
verify the name to FUNCTION number relationship using
the SMS Controller.
Caution: The projector adjustments and settings stored as
the selected FUNCTION are immediately applied
projector. During this period of time the auditorium screen
may go dark. No confirmation message of the FUNCTION
key selection is displayed. Also, there is no "undo". If the
previous setup was the results of a FUNCTION setting
applied based on a CPL association, projector settings are
changed to the new settings. Adjustments made but not
saved on the FUNCTION SETUP pane will be lost.
The Projector FUNCTION selected is retained until a
different FUNCTION selection is made or until a different
FUNCTION is selected as a result of presenting a CPL
with a different FUNCTION association or a SPL that
includes FUNCTION Commands.
The FUNCTION selected will be the Current Function
appearing on the FUNCTION SETUP screen and will be
modified based on projector settings when Save to
FUNCTION is executed.

Set Luminance Offset

During installation of the SMS the Lamp Power is adjusted
to provide the desired screen illumination (measured in
foot/Lamberts). This value can be set in a FUNCTION as
1.Assumes that the appropriate Projection Type has been
configured.
27
Projector
the calibrated lamp brightness for an associated aspect
ratio.
On occasion, it is desirable to increase the screen
luminance, i.e., raise lamp brightness, to meet special
presentation needs. The Luminance Offset slider allows
you to make this temporary (offset) adjustment.
Luminance Offset
Control
Lower
Note: The Luminance Offset will remain in effect until you
tap RESET which returns the offset to "0" (zero).

Luminance Offset (Adjust)

The Luminance Offset control is a slider which allows you
to make temporary adjustments to increase or decrease the
screen luminance value (ft-L) within the predefined limits
of Lamp Power for the bulb.
1
To adjust the Luminance Offset, tap Menu, tap Projector,
to the
tap Projector Control and then either touch and drag the
Luminance Offset control or press and hold the Plus
or Minus buttons until the desired screen luminance
(image brightness) is obtained.
Note: While adjusting Luminance Offset affects lamp
brightness, the Lamp Power indicated on the FUNCTION
SETUP screen is not changed.

Luminance Offset RESET

To return the screen luminance to the value stored in the
currently selected FUNCTION, tap Menu, tap Projector,
tap Projector Control and then tap RESET located below
the Luminance Offset slider.

Function Setup

Just as in film projection there are a number of issues
related to the configuration of the Digital Cinema projector
for the venue and/or the content being presented. One
easily called to mind in film is the aperture plate which is
selected based on the image format. Because the Digital
Cinema system can present content of varying formats the
settings are much more complex. To ease the projector
setup task the SRX-R320 Projectors allow you to save
specific configuration settings under twenty selectable
Value
RESET
Raise