Sealey CH2800.V2 Instructions

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Warning!
instruction Hot surface
manual
1. saFetY
eLectricaL saFetY
1.1.
warning! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
electrical safety information, it is important that the following information is read and understood.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
dO nOt pull or carry the appliance by the power cable.
8
dO nOt pull the plug from the socket by the cable.
8
dO nOt use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or is
8
replaced immediately by a qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. generaL saFetY
Familiarise yourself with the applications and limitations of the heater.
9
ensure that heater body is positioned on a firm, horizontal dry surface.
9
Keep away from flammable objects/materials/surfaces. This product gets very hot during use. Use in a location where accidental
9
contact (particularly by children) is unlikely.
ensure on/off switches are set to 'off' before connecting power cord to power supply.
9
ensure the heater is in good order and condition before use. If in any doubt do not use the unit and contact an electrician.
9
only use recommended attachments and parts. To use unauthorised parts may be dangerous and will invalidate your warranty.
9
Check that element guard is in place, undamaged and firmly attached.
9
Keep tools and other items away from the heater when it is in use.
9
Keep the work area clean and clear of unnecessary items.
9
Keep children and unauthorised persons away from the heater, as it gets very hot. Children of less than 3 years should be kept away
9
unless continuously supervised.
disconnect from mains and allow to cool before moving or attempting any cleaning or maintenance.
9
dO nOt get the heater wet or use in damp or wet locations or areas where there is condensation.
8
dO nOt locate the heater below the power outlet.
8
dO nOt remove plug from mains supply by pulling on power cord.
8
dO nOt move the heater whilst in operation or even when still warm.
8
dO nOt touch the heater elements, even when cold.
8
always switch off heater, disconnect from power supply and allow cooling for at least one hour before attempting to touch heater
9
cassette.
dO nOt remove safety guard whilst heater is switched on. Turn off and allow cooling (as above) before servicing.
8
dO nOt disassemble the heater for any reason. The heater must be checked by qualified personnel only.
8
dO nOt use this product to perform a task for which it has not been designed.
8
dO nOt operate heater without safety guard or elements installed.
8
warning! if a fuse blows, ensure it is replaced with an identical fuse type and rating.
‰
© Jack Sealey limited
standing ceramic heater 1.4/2.8kw 230v
model no:
dO nOt Indoor use only
cover
Original Language Version
ch2800.v2
Recommended fuse rating
13 Amp
CH2800.V2| Issue:3 (H,F) 02/05/18