Sealey CH2013.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
DO NOT
Refer to
instruction cover
manual
NOTE: This product is only suitable for use in well insulated areas or occasional use.
1. SAFETY
i
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
if the used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test)
tested.
Electrical safety information, it is important that the following information is read and understood.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - see
9
fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. GENERAL SAFETY
Familiarise yourself with the applications and limitations of the heater.
9
Ensure that heater housing is positioned with feet and tilt switch on a firm, horizontal dry surface.
9
Keep away from flammable objects/materials/surfaces. This product gets very hot during use. Use in a location where accidental
9
contact (particularly by children) is unlikely.
Ensure the 4 position switch is set to 'off ' before connecting power cord to power supply.
9
Ensure the heater is in good order and condition before use. If in any doubt DO NOT use the unit and contact an electrician.
9
Keep tools and other items away from the heater when it is in use.
9
Keep the area clean and clear of unnecessary items.
9
Keep children and unauthorised persons away from the heater, as it gets very hot.
9
Disconnect from mains and allow to cool before moving or attempting any cleaning.
9
DO NOT get the heater wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT remove plug from mains supply by pulling on power cord.
8
DO NOT move the heater whilst in operation or even when still warm.
8
DO NOT disassemble the heater for any reason. The heater must be checked by qualified personnel only.
8
DO NOT use this product to perform a task for which it has not been designed.
8
WARNING! If a fuse blows, ensure it is replaced with an identical fuse type and rating. If it blows again DO NOT use the unit and
‰
contact an electrician
DO NOT place any object on the heater at any time.
8
WARNING! Ensure any object is at least 200cm from the heater front face.
‰
DO NOT leave unattended. When not in use, store the heater carefully in a safe, dry, childproof location.
8
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities
or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a
© Jack Sealey Limited
CERAMIC FAN HEATER 1400W/230V
2 HEAT SETTINGS
MODEL NO:
Warning: Warning:
Electric shock Hot surface
hazard
Original Language Version
CH2013.V3
Indoor use
only
Recommended fuse rating
13 Amp
CH2013.V3 Issue 1 31/05/19