Sealey CH20 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMP P OR R TA TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH H E P P RO O DUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE E RS S ON N AL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Electrical shock
instructions hazard
NOTE: THIS PRODUCT IS ONLY SUITABLE FOR USE IN WELL INSULATED AREAS OR OCCASIONAL USE.
1. SAFETY
1.1. ELECTRICAL SAFETY
 WARNING! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey Stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fi tted with the
correct fuse - see fuse rating in these instructions.
 DO NOT pull or carry the appliance by the power cable.
 DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a fi rm grip on the plug.
 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualifi ed electrician.
1.1.4. This product is fi tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualifi ed electrician.
Class II products are wired with live (brown) and neutral (blue) only, and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.

Sealey recommend that repairs are carried out by a qualifi ed electrician.
1.2. GENERAL SAFETY
 Familiarise yourself with the applications and limitations of the fan heater.
 Keep away from fl ammable objects, materials and surfaces.
 This product gets very hot during use. Use in a location where accidental contact, particularly by children, is unlikely.
 Ensure the fan heater is set to the "OFF" position before connecting to the mains power supply.
 Ensure the fan heater is in good working order and condition before use. If in any doubt DO NOT use the fan heater and contact a
qualifi ed electrician.
 Keep tools and other items away from the fan heater when in use.
 Keep the area clean and clear of unnecessary items.
Keep children and unauthorised persons away from the fan heater.

 Disconnect the fan heated from the mains and allow to cool before moving or attempting any cleaning.
 DO NOT get the fan heater wet or use in damp or wet locations or in areas where there is condensation.
 DO NOT remove the plug from the mains supply by pulling on the power cord.
 DO NOT move the fan heater whilst in operation or even while it is still warm.
 DO NOT disassemble the fan heater for any reason. Use an authorised service agent only.
 DO NOT use this product to perform a task for which it has not been designed.
 WARNING! If a fuse blows, ensure it is replaced with an identical fuse type and rating. If it blows again DO NOT use the fan heater
Contact a qualifi ed electrician.
 DO NOT place any object on the fan heater at any time.
 DO NOT leave unattended. When not in use, store the fan heater in a safe, dry childproof location.
 DO NOT connect the fan heater to an on/off timer or any other equipment which can automatically switch the fan heater on.
© Jack Sealey Limited
2000W INDUSTRIAL CERAMIC FAN HEATER
2800W INDUSTRIAL CERAMIC FAN HEATER
MODEL NO:
Hot surfaces Do not cover
Original Language Version
CH20,CH28
Indoor use
only
Recommended fuse rating
13 Amp
CH20,CH28 Issue 1 12/04/21