Download
Share
Print this page
Hitachi S10 Series Manual
  1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Controller
  5. S10 Series
  6. Manual
Hitachi S10 Series Manual

Hitachi S10 Series Manual

Sio driver
Hide thumbs

Advertisement

Quick Links

S10 Series SIO
Driver
1
System Configuration....................................................................................................... 3
2
Selection of External Device ............................................................................................ 7
3
Example of Communication Setting ................................................................................. 8
4
Setup Items .................................................................................................................... 18
5
Cable Diagram ............................................................................................................... 23
6
Supported Device........................................................................................................... 35
7
Device Code and Address Code.................................................................................... 44
8
Error Messages.............................................................................................................. 53
1
Hitachi, Ltd.

Advertisement

loading

Related Manuals for Hitachi S10 Series

Summary of Contents for Hitachi S10 Series

  • Page 1: Table Of Contents

    Hitachi, Ltd. S10 Series SIO Driver System Configuration....................... 3 Selection of External Device .................... 7 Example of Communication Setting ................. 8 Setup Items ........................18 Cable Diagram ....................... 23 Supported Device......................35 Device Code and Address Code..................44 Error Messages......................53...
  • Page 2 S10 Series SIO Driver Introduction This manual describes how to connect the Display and the External Device (target PLC). In this manual, the connection procedure will be described by following the below sections: System Configuration "1 System Configuration" (page 3)

  • Page 3: System Configuration

    S10 Series SIO Driver System Configuration The system configuration in the case when the External Device of Hitachi, Ltd. and the Display are connected is shown. Series Link I/F SIO Type Setting Example Cable Diagram UP LINK Connector RS422/485 Setting Example 1...
  • Page 4 S10 Series SIO Driver IPC COM Port When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please refer to the IPC manual for details. Usable port Usable Port Series RS-232C RS-422/485(4 wire)
  • Page 5 S10 Series SIO Driver When setting up communication between an External Device and the RS-232C/422/485 interface module, use the IPC (RS-232C) or PS5000 (RS-422/485) cable diagrams. However, when using PFXZPBMPR42P2 in a RS-422/485 (4-wire) configuration with no flow control, connect 7.RTS+ and 8.CTS+, and connect 6.RTS- and 9.CTS-.
  • Page 6 S10 Series SIO Driver RS-422/485 (4 wire) DIP Switch Setting Description Reserved (always OFF) SIO type: RS-422/485 Output mode of SD (TXD) data: Always output Terminal resistance (220Ω) insertion to SD (TXD): None Terminal resistance (220Ω) insertion to RD (RXD): None...

  • Page 7: Selection Of External Device

    Manufacturer Select the manufacturer of the External Device to connect. Select "Hitachi, Ltd.". Select the External Device model (series) and the connection method. Select "S10 Series SIO". In System configuration, make sure the External Device you are connecting is supported by Series "S10 Series SIO".

  • Page 8: Example Of Communication Setting

    S10 Series SIO Driver Example of Communication Setting The following shows examples of communication settings of the Display and the External Device, which is recommended by Pro-face. Setting Example 1 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].
  • Page 9 S10 Series SIO Driver Setting Example 2 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 10 S10 Series SIO Driver Setting Example 3 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 11 S10 Series SIO Driver Setting Example 4 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 12 S10 Series SIO Driver Setting Example 5 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 13 S10 Series SIO Driver Setting Example 6 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 14 S10 Series SIO Driver Setting Example 7 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 15 S10 Series SIO Driver Setting Example 8 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 16 S10 Series SIO Driver Setting Example 9 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...
  • Page 17 S10 Series SIO Driver 3.10 Setting Example 10 Settings of GP-Pro EX Communication Settings To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC]. Device Setting To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]...

  • Page 18: Setup Items

    S10 Series SIO Driver Setup Items Set communication settings of the Display with GP-Pro Ex or in offline mode of the Display. The setting of each parameter must be identical to that of the External Device. "3 Example of Communication Setting" (page 8)
  • Page 19 S10 Series SIO Driver Setup Items Setup Description You can switch RI/VCC of the 9th pin when you select RS232C for SIO type. RI/VCC When you connect to IPC, you need to use the IPC change switch to change RI/5V. Please refer to the manual of IPC for details.
  • Page 20 S10 Series SIO Driver Settings in Offline Mode • Refer to the Maintenance/Troubleshooting guide for information on how to enter offline mode or about the operation. Maintenance/Troubleshooting Guide "Offline Mode" • The number of the setup items to be displayed for 1 page in the off-line mode depends on the Display in use.
  • Page 21 S10 Series SIO Driver Setup Items Setup Description Use an integer from 1 to 127 to enter the time (s) for which the Display waits for the Timeout (s) response from the External Device. In case of no response from the External Device, use an integer from "0 to 255" to enter Retry how many times the Display retransmits the command.
  • Page 22 S10 Series SIO Driver Option To display the setting screen, touch [Device/PLC Settings] from [Peripheral Equipment Settings]. Touch the External Device you want to set from the displayed list, and touch [Option]. Setup Items Setup Description You can switch RI/VCC of the 9th pin when you select RS232C for SIO type.

  • Page 23: Cable Diagram

    S10 Series SIO Driver Cable Diagram The cable diagram shown below may be different from the cable diagram recommended by Hitachi, Ltd.. Please be assured there is no operational problem in applying the cable diagram shown in this manual. •...
  • Page 24 S10 Series SIO Driver All GP models except GP-3200 Series and AGP-3302B All GP4000 models except GP-4100 Series, GP-4*01TM, GP-Rear Module, GP-4201T and GP-4*03T Except SP-5B00 When using a Terminal Block Conversion Adapter (CA3-ADPTRM-01) instead of the RS-422 Terminal Block Conversion Adapter, refer to Cable Diagram 1A.
  • Page 25 S10 Series SIO Driver Display Terminal block External Device Signal name Shield D-Sub 9pin (socket) Display Signal name CA3-ADPCOM-01 SD-H SD-L RD-H CA3-ADPTRM-01 RD-L Your own cable Display External Device D-Sub 9pin (socket) D-Sub 9pin (socket) Termination Shield Signal name...
  • Page 26 S10 Series SIO Driver Display Terminal block External Device Shield Signal name D-Sub 9pin (socket) Display Signal name CA4-ADPONL-01 SD-H SD-L RD-H CA3-ADPTRM-01 RD-L Your own cable Display D-Sub 9pin (plug) External Device Signal name D-Sub 9pin (socket) Shield TRMRX...
  • Page 27 S10 Series SIO Driver Display Terminal block External Device Shield Signal name D-Sub 9pin (socket) Display Signal name SD-H SD-L RD-H PFXZCBADTM1 RD-L Your own cable Display External Device D-Sub 9pin (socket) D-Sub 9pin (socket) Termination Shield Signal name Signal name resistance 100Ω...
  • Page 28 S10 Series SIO Driver Display External Device Terminal block D-Sub 9pin (socket) Shield Signal name Signal name Termination resistance *1 SD-H SD-L Display RD-H RD-L Your own cable The resistance in the Display is used as the termination resistance. Set the value of the DIP Switch on the rear of the Display as shown in the table below.
  • Page 29 S10 Series SIO Driver Cable Diagram 2 Display Cable Remarks (Connection Port) GP3000 (COM1) GP4000 (COM1) SP5000 (COM1/2) SP-5B00 (COM1) Your own cable Cable length: 15m or less ST (COM1) LT3000 (COM1) PC/AT GP-4115T (COM1) Your own cable Cable length: 15m or less...
  • Page 30 S10 Series SIO Driver Cable Diagram 3 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face GP3000 (COM1) CA3-ADPCOM-01 AGP-3302B (COM2) GP-4*01TM (COM1) Please refer to the Connector terminal block conversion adapter by Pro-face GP-Rear Module manual of the External...
  • Page 31 S10 Series SIO Driver Display Terminal block Shield Signal name External Device Display Signal name CA3-ADPCOM-01 UTX-H UTX-L URX-H CA3-ADPTRM-01 URX-L Series resistance 100Ω (1/2W) Your own cable Display Shield External Device D-Sub 9pin (socket) Termination Signal name Signal name resistance 100Ω...
  • Page 32 S10 Series SIO Driver Display Terminal block Shield Signal name External Device Display Signal name CA4-ADPONL-01 UTX-H UTX-L URX-H CA3-ADPTRM-01 URX-L Series resistance 100Ω (1/2W) Your own cable Display D-Sub 9pin (plug) Shield Signal name External Device Signal name TRMRX...
  • Page 33 S10 Series SIO Driver Display Terminal block Shield Signal name External Device Display Signal name UTX-H UTX-L URX-H PFXZCBADTM1 URX-L Series resistance 100Ω (1/2W) Your own cable Display Shield External Device D-Sub 9pin (socket) Termination Signal name Signal name resistance 100Ω...
  • Page 34 S10 Series SIO Driver Display Shield External Device Terminal block Signal name Signal name Termination resistance *1 UTX-H UTX-L Display URX-H URX-L Series resistance 100Ω (1/2W) Your own cable • When making your own connections, we recommend using KPEV-SB-3P 0.5mm cable by Hitachi Cable, Ltd..

  • Page 35: Supported Device

    S10 Series SIO Driver Supported Device Range of supported device address is shown in the table below. Note that the actually supported range varies depending on the External Device to be used. Please check the actual range in the manual of your External Device.
  • Page 36 S10 Series SIO Driver Device Bit Address Word Address 32 bits Remarks Timer (Elapsed Value) TC000 - TC1FF Timer (Setup Value) TS000 - TS1FF One-shot Timer (Elapsed Value) UC000 - UC0FF One-shot Timer (Setup Value) US000 - US0FF Counter (Elapsed Value)
  • Page 37 S10 Series SIO Driver • When you access the External Device using the Direct Memory Address, do not access the memory address that the system uses. If you conduct it, an error may occur. For details concerning the address, refer to the manual attached to the External Device.
  • Page 38 S10 Series SIO Driver HIDIC-S10α (2α/2αE/2αH) : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks External Input X000 - XFFF XW000 - XWFF0 External Output Y000 - YFFF YW000 - YWFF0...
  • Page 39 S10 Series SIO Driver Device Bit Address Word Address 32 bits Remarks Function Work Register FW000 - FWBFF Function Data Register DW000 - DWFFF Extended Register MS000 - MSFFF DM00000000 - Direct Memory Address DMFFFFFFFE According to External Device specification, the highest bit is "0" and the lowest bit is "15". When the highest bit turns ON, that bit is considered the highest and "32768"...
  • Page 40 S10 Series SIO Driver HIDIC-S10α (4α/4αF) : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks External Input X000 - XFFF XW000 - XWFF0 External Output Y000 - YFFF YW000 - YWFF0...
  • Page 41 S10 Series SIO Driver Device Bit Address Word Address 32 bits Remarks Function Work Register FW000 - FWBFF Function Data Register DW000 - DW7FF DM00000000 - Direct Memory Address DMFFFFFFFE According to External Device specification, the highest bit is "0" and the lowest bit is "15". When the highest bit turns ON, that bit is considered the highest and "32768"...
  • Page 42 S10 Series SIO Driver S10mini Series : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks External Input X000 - XFFF XW000 - XWFF0 External Output Y000 - YFFF YW000 - YWFF0...
  • Page 43 S10 Series SIO Driver Device Bit Address Word Address 32 bits Remarks Work Register FW000 - FWBFF Data Register DW000 - DWFFF Extended Register MS000 - MSFFF DM00000000 - Direct Memory Address DMFFFFFFFE According to External Device specification, the highest bit is "0" and the lowest bit is "15". When the highest bit turns ON, that bit is considered the highest and "32768"...

  • Page 44: Device Code And Address Code

    S10 Series SIO Driver Device Code and Address Code Use device code and address code when you select "Device Type & Address" for the address type in data displays. S10V Series Device Device Code Device Address Code Name (HEX) External Input...
  • Page 45 S10 Series SIO Driver Device Device Code Device Address Code Name (HEX) Timer (Elapsed Value) 0060 Word Address Timer (Setup Value) 0061 Word Address One-shot Timer (Elapsed Value) 0062 Word Address One-shot Timer (Setup Value) 0063 Word Address Counter (Elapsed Value)
  • Page 46 S10 Series SIO Driver Device Device Code Device Address Code Name (HEX) Direct Memory Address 000F (DM80000000 - DM8FFFFFFE) Direct Memory Address 0010 (DM90000000 - DM9FFFFFFE) Direct Memory Address 0011 (DMA0000000 - DMAFFFFFFE) Direct Memory Address 0012 (DMB0000000 - DMBFFFFFFE)
  • Page 47 S10 Series SIO Driver HIDIC-S10α (2α/2αE/2αH) Device Device Code Device Address Code Name (HEX) External Input 0080 Value of word address divided by 0x10 External Output 0081 Value of word address divided by 0x10 Intermediate Register 0082 Value of word address divided by 0x10...
  • Page 48 S10 Series SIO Driver Device Device Code Device Address Code Name (HEX) Direct Memory Address 0007 (DM00000000 - DM0FFFFFFE) Direct Memory Address 0008 (DM10000000 - DM1FFFFFFE) Direct Memory Address 0009 (DM20000000 - DM2FFFFFFE) Direct Memory Address 000A (DM30000000 - DM3FFFFFFE)
  • Page 49 S10 Series SIO Driver HIDIC-S10α (4α/4αF) Device Device Code Device Address Code Name (HEX) External Input 0080 Value of word address divided by 0x10 External Output 0081 Value of word address divided by 0x10 Intermediate Register 0082 Value of word address divided by 0x10...
  • Page 50 S10 Series SIO Driver Device Device Code Device Address Code Name (HEX) Direct Memory Address 0007 (DM00000000 - DM0FFFFFFE) Direct Memory Address 0008 (DM10000000 - DM1FFFFFFE) Direct Memory Address 0009 (DM20000000 - DM2FFFFFFE) Direct Memory Address 000A (DM30000000 - DM3FFFFFFE)
  • Page 51 S10 Series SIO Driver S10mini Series Device Device Code Device Address Code Name (HEX) External Input 0080 Value of word address divided by 0x10 External Output 0081 Value of word address divided by 0x10 Internal Register 0082 Value of word address divided by 0x10...
  • Page 52 S10 Series SIO Driver Device Device Code Device Address Code Name (HEX) Data Register 0000 Word Address Extended Register 0006 Word Address Direct Memory Address 0007 (DM00000000 - DM0FFFFFFE) Direct Memory Address 0008 (DM10000000 - DM1FFFFFFE) Direct Memory Address 0009...

  • Page 53: Error Messages

    S10 Series SIO Driver Error Messages Error messages are displayed on the Display screen as follows: "No. : Device Name: Error Message(Error Occurrence Area)". Each description is shown below. Item Description Error No. Name of the External Device where an error occurs. Device name is a title of the External Device Name Device set with GP-Pro EX.

This manual is also suitable for:

S10v seriesS10mini