Page 1
Preliminary 1(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 Receiver: Info: M. Carstens-Behrens mycable GmbH Manual MB 91F467 / MB 86276 Evaluation Board Version PA 6.2 May 23, 2008 http://www.fujitsu.com/emea/services/microelectronics...
Page 2
Preliminary 2(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01...
Page 3
MB 91F467 / MB 86276 Evaluation Board Summary This manual provides detailed technical information for system architects, hardware and software developers, who work with the MB 91F467 / MB 86276 Evaluation board version PA6 for evaluation and development purpose. Enclosures None.
Page 4
Preliminary 4(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 Revision History Version Date Sign Description PA 6.1 2008-05-06 Create this document First preliminary distributed version PA 6.2 2008-05-23 Contact Information mycable GmbH Michael Carstens-Behrens ( hardware and commercial ) Email mcb@mycable.de...
It is the engineer’s reference for evaluation, system development and prototyping based on the module. This document covers all available hardware versions regarding their configuration options and revision state. 1.2 Putting into Operation Connect the MB 91F467 / MB 86276 Evaluation board with a DC power supply. For details see chapter power supply.
Mycable01 MB 91F467 / MB 86276 Evaluation Board 2.1 System Architecture The system architecture of the MB 91F467 / MB 86276 Evaluation board is shown in picture 2-1. Block diagram has to be added Pic. 2-1: MB 91F467 / MB 86276 Evaluation board block diagram...
Page 8
Preliminary 8(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 Picture 2-2: MB 91F467 / MB 86276 Evaluation Board top side Picture 2-3: MB 91F467 / MB 86276 Evaluation Board bottom side...
Preliminary 9(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 2.2 Function Units Overview in the available interfaces: 10/100 Ethernet – 2x serial ports – 2x CAN – Power supply – Video Inputs – Video Outputs –...
2.2.1 Power Supply Picture 2-4: Power supply connector Connect the MB 91F467 / MB 86276 Evaluation board with a power supply between 5 and 34 V DC and approximate 10 Watt at connector X100. Be aware to use the correct polarity as shown in picture 2-5.
2.2.3 CPU MB91F467DA Pic. 2-6: CPU MB91F467DA The CPU MB91F467DA from Fujitsu ( U500 ) is used. External 2x 1 Gbit Flash Memory ( U580, U581 ), 2x 128Mx16 SDRAM ( U590, U591 ) and 512kx16 SRAM ( U592 ) are connected.
Page 12
Preliminary 12(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 The CPU MB91F467DA has following features Core frequency 96 MHz Resource frequency 48 MHz Watchdog Bit Search Reset Input Clock Modulator DMA 5 ch MPU/EDSU 16 BP (8 MPU ch) Flash external 1024 kB + 64 kB Flash Protection...
Page 13
Preliminary 13(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 Following picture shows the block diagram of the CPU. More details see data sheet. Pic. 2-7: Block diagram of CPU MB91F467DA...
Mycable01 2.2.4 Graphic Display Controller MB86276 LIME Pic. 2-8: Graphic display controller MB86276 The graphic display controller MB86276 ( U300 ) also called LIME from Fujitsu is connected to the CPU. The MB86276 has following features: • CMOS 0.18µm technology •...
Page 15
Preliminary 15(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 • Built-in alpha blending, anti-aliasing and chroma-keying • Rendering Engine for various kinds of 2D graphic acceleration functions • Texture Mapping Unit for 2D polygon support up to 4096x4096 textures •...
Preliminary 16(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 2.2.5 Buttons Pic. 2-9: Buttons If the button SW100 which is not labeled will be pressed a reset will be generated. If the button SW501 which is labeled with ABORT will be pressed the interrupt 0 ( P24_0 ) will be generated.
Preliminary 18(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 Signal Function RS232_0_CTS Clear to send RS232_0_RTS Request to send RS232_0_RI Ring indicator Table 2-4: Pin assignment X800 and X801 2.2.8 Ethernet Pic. 2-12: Ethernet connector At the RJ45 connector X600 the Ethernet interface is available.
Preliminary 19(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 If this resistor is not populated the FIFO_SEL pin is strapped by the 10k Ohm resistor R610 to VCC then all accesses to U600 are to the RX or TX data FIFO and the upper addresses A[7:3] are ignored.
Page 20
Preliminary 20(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 120 Ohm termination is configurable per line via switches on board: SW700: 120 Ohm Termination for CAN 0 SW701: 120 Ohm Termination for CAN 1 Pic.
Preliminary 21(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 2.2.10 Video Inputs Pic. 2-15: Video input connectors The Cinch video connectors X480 ( AVIN0 ) and X481 ( AVIN1 ) are connected directly to GDC module interface connector X301 pin 35 and 37 ( Ground pin 33 and 34 ).
Preliminary 22(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 2.2.11 Video Outputs Pic. 2-16: Video output connectors The digital RGB video output 0 from the LIME is connected to connector X402, transmitter SiI164CT64 ( U400 ) and triple 8-Bit high speed video digital-to-analog converter ( DAC ) ADV7125JSTZ240 ( U402 ).
Page 23
Preliminary 23(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 strapped to VCC by resistor RN402 so the slave address for readings is 0x73 and the slave address for writings is 0x72. The SiI164 support receiver and hot plug detection. The triple 8-Bit high speed video digital-to-analog converter ( DAC ) ADV7125JSTZ240 ( U402 and U403 ) from Analog Devices convert the digital RGB666 video output signals from the LIME to an analog video signals.
Page 24
Preliminary 24(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 Signal Function Digital RGB output 5 Data red VO0_R5 Digital RGB output 6 Data red VO0_R6 Digital RGB output 7 Data red VO0_R7 Video output interface horizontal sync output VO0_HSYNC Video output interface vertical sync output VO0_VSYNC...
Preliminary 25(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 2.2.12 GPIOs Pic. 2-17: GPIO connector Some GPIOs from the CPU are available at connected X900 FTSH-110-01-L-DV-K-A-P from Samtec. Following table shows the assignment of pins, signals and function from the connector X900: Signal Function VCC33...
Page 26
Preliminary 26(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 Signal Function GPIO13 P27_7 GPIO14 P26_0 GPIO15 P26_1 GPIO16 P26_2 GPIO17 P26_3 Ground...
Preliminary 27(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 Hardware Variants Up to now only PCB version PA6 without variants is available.
Preliminary 28(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 Placement of Components...
Page 29
Preliminary 29(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01...
Preliminary 30(30) Prepared Document Number Manfred Ortmann Approved Checked Date Revision Storage 2008-05-23 PA 6.2 Mycable01 Mechanical Dimensions The MB 91F467 / MB 86276 Evaluation board has a size of 160.0 x 100.0 mm.